Husqvarna 968999225 / ZTH7227KOB - Manual

Page 3 - CONTENTS

3 CONTENTS INTRODUCTION .................................. 4-5 SYMBOLS & DECALS ......................... 6 SAFETY INSTRUCTIONS .................... 7 General use and safety rules ...... 7-8 Driving on slopes ........................ 9 Children safety ............................ 10 Service safe...

Page 4 - INTRODUCTION; Introduction; Congratulations

4 INTRODUCTION Introduction Congratulations Thank you for purchasing a Husqvana ride-on mower. This machine is built for the greatest effi-ciency and rapid mowing of large areas. Convenient controls and a hydrostatic transmission regu-lated by steering levers also contribute to the machine’s perform...

Page 5 - Good Service

5 INTRODUCTION Good Service Husqvarna’s products are sold all over the world and only in specialized retail stores with completeservice. This ensures that you as a customer receive only the best support and service. Before theproduct is delivered, the machine has, for example, been inspected and adj...

Page 6 - SYMBOLS AND DECALS; Symbols and Decals; Used in this publication to notify the reader of a risk of; personal injury; material damage; , particularly if the reader

6 SYMBOLS AND DECALS Symbols and Decals These symbols are found on the machine and in the operator’s manual.Study them carefully so that you know what they mean. WA RNING !X xx xx xx xx xx xx xx xx x x xx x x X xx xx xx xx xx xx .xx xx xx x xx x x xx xx xx x x x. Used in this publication to notify t...

Page 7 - SAFETY INSTRUCTIONS; Safety Instructions; These instructions are for your safety. Read them carefully.; General Use; Slow down before turning.

7 SAFETY INSTRUCTIONS Safety Instructions These instructions are for your safety. Read them carefully. WARNING! This symbol means that important safety instructions need to be emphasized. Itconcerns your safety. General Use • Read all instructions in this operator’s manualand on the machine before s...

Page 9 - Driving on Slopes; Always drive evenly and slowly on slopes.

9 6003-004 Mow up and down, not side-to-side. Driving on Slopes SAFETY INSTRUCTIONS Driving on slopes is one of the operations wherethe risk is greatest that the driver will lose controlor the machine will tip over, which can result inserious injury or death. All slopes require extracaution. If you ...

Page 12 - IMPORTANT INFORMATION

12 • Never use the machine indoors or in spaceslacking proper ventilation. The exhaust fumescontain carbon monoxide, and odorless, poi-sonous, and lethal gas. • Stop and inspect the equipment if you run overor into anything. If necessary, make repairsbefore starting. • Never make adjustments with th...

Page 13 - PRESENTATION; FUEL CAP; Presentation; Thank you for buying a

13 PRESENTATION FUEL CAP MOTION CONTROLLEVERS PARKINGBRAKE DECK LIFTLEVER FOOTPLATE KEY SWITCH BLADEENGAGEMENTSWITCH THROTTLE Presentation Thank you for buying a HUSQVARNA! Before operating your new mower, read, understandand follow the safety instructions and otherdirections in this manual. Lawnmow...

Page 14 - SETUP AND ADJUSTMENTS; Setup; Cutting Height; Stop the mower and disengage the blades.

14 SETUP AND ADJUSTMENTS WARNING: No settings or adjustments are tobe made unless: Engine is stopped, key hasbeen removed, park brake is on and batterycable removed from battery. Setup Uncrate machine. Mount rear drive wheels using the lug nutsinstalled on the hubs. Check the tire pressure in all fo...

Page 15 - Mower Deck Leveling; Reverse Spring Detent Adjustment; Stop engine and remove key.

15 SETUP AND ADJUSTMENTS Mower Deck Leveling Position machine on a flat surface. Preferablylevel concrete. Check the tire pressure in all four tires. Inflationshould be 15 psi. Place 2x4’s on edge under the cutting deckfrom front to rear and lower the deck downonto 2x4’s. Adjust the four lower chain...

Page 16 - Motion Control Linkage Adjustment; Loosen Here; Park Brake Adjustment; Loosen here

16 Motion Control Linkage Adjustment This adjustment must be made with the rearwheels rotating. Raise the rear of the machineand block it up so the wheels are free to rotate. CAUTION: Keep hands, feet and clothingaway from rotating tires. Tilt seat forward and remove the seat rod so theseat may rota...

Page 17 - OPERATING INSTRUCTIONS; Starting and operation; Release parking brake.; Controls; Operating instructions; Motion Control Lever Pattern

17 Run engine full throttle to make sure wheels donot rotate. Readjust if any rotation occurs. Repeat the whole process for the opposite sideand tighten the nuts against the ball joints. Turn machine off. Reinstall the seat rod and check the wiringharness to the seat safety switch for a goodconnecti...

Page 18 - Use extra; Key Switch

18 By moving the levers an equal amount forwardor back the machine will move in a straight linein that direction. FIG - 11 Movement of either lever forward will cause theright or left wheel to rotate in a forward direc-tion. To stop movement pull both levers into theneutral position. To turn right w...

Page 19 - Maintenance; Husqvarna; dealer is recommended; Engine oil; MAINTENANCE; Safety interlock system; Operating; Cutter Housings

19 Fuel shut off valve is located at the right rear of theseat. The valve has three positions a right tank, lefttank and center is the off position. FIG - 13. Pump release valves located at the right frontcorner of the pumps. Used to release thesystem so the machine may be moved by handwhen not runn...

Page 20 - ONLY USE

20 Hardware Check daily. Inspect the entire machine forloose or missing hardware. Air filter See engine manufacturers specifications forcleaning and replacement intervals. Hydraulic system Check oil level in tank daily. Oil level should be3/4” to 1” below the top of the tank. Check allfittings, hose...

Page 23 - Maintenance Schedule; For ZTH Riders

23 Maintenance Schedule For ZTH Riders Maintenance Maintenance Interval (hours)Daily 25 50 100 200 250 500 Engine (4) Check oil level X Change oil and filter (1) X Clean the air filter’s (3) X Replace air filter’s (3) X Check for fuel and oil leakage X Clean cooling flanges (3) X Check cooling air i...

Page 24 - TROUBLE SHOOTING; PROBLEM; ENGINE WILL NOT START.

24 TROUBLE SHOOTING PROBLEM POSSIBLE CAUSES ENGINE WILL NOT START. Blade switch on.Drive levers not in the neutral slots.Operator not in seat.Park brake disengaged.Dead battery.Fuel valve closed or in the wrong position.No fuel.Spark plugs defective.Spark plug wires off. MACHINE WILL NOT MOVE OR MOV...

Page 25 - WIRING DIAGRAMS; CONSOLE HARNESS

25 WIRING DIAGRAMS CONSOLE HARNESS FrameHarness Engine Clutch LeftMotionControl HourMeter BladeSwitch Seat StarterSwitch RightMotionControl P/N104414

Page 26 - CONSOLE HARNESS SCHEMA

Page 27 - FRAME HARNESS

27 FRAME HARNESS WIRING DIAGRAMS Clutch EnginePigtail Ground toEngine StarterSolenoid ParkBrake ConsoleHarness BrakeRelay StartRelay RunRelay P/N104964

Husqvarna 968999225 / ZTH7227KOB - Manual

Table of Contents:

Summary

Other Husqvarna Models