Page 2 - KEY TO SYMBOLS; Symbols
2 – English KEY TO SYMBOLS Symbols WARNING! Clearing saws, brushcutters and trimmers can be dangerous! Careless or incorrect use can result in serious or fatal injury to the operator or others. Please read the operator’s manual carefully and make sure you understand the instructions before using the...
Page 3 - CONTENTS; Contents
English – 3 CONTENTS Contents Note the following before starting: Please read the operator’s manual carefully. Long-term exposure to noise can result in permanent hearing impairment. So always use approved hearing protection. Maintenance, replacement, or repair of the emission control devices and sy...
Page 4 - INTRODUCTION
4 – English INTRODUCTION Dear customer! Congratulations on your choice to buy a Husqvarna product! Husqvarna is based on a tradition that dates back to 1689, when the Swedish King Karl XI ordered the construction of a factory on the banks of the Huskvarna River, for production of muskets. The locati...
Page 6 - GENERAL SAFETY PRECAUTIONS; Important
6 – English GENERAL SAFETY PRECAUTIONS Important Personal protective equipment HEARING PROTECTION Wear hearing protection that provides adequate noise reduction. EYE PROTECTION Always wear approved eye protection. If you use a visor then you must also wear approved protective goggles. Approved prote...
Page 7 - Throttle lock; Cutting attachment guard
English – 7 GENERAL SAFETY PRECAUTIONS Throttle lock The throttle lock is designed to prevent accidental operation of the throttle control. When you press the lock (A) (i.e. when you grasp the handle) it releases the throttle control (B). When you release the handle the throttle control and the thro...
Page 8 - Vibration damping system
8 – English GENERAL SAFETY PRECAUTIONS Vibration damping system Your machine is equipped with a vibration damping system that is designed to reduce vibration and make operation easier. Use of incorrectly wound cord or an incorrect cutting attachment increases the level of vibration. See instructions...
Page 9 - Locking nut; Cutting equipment; Trimmer head
English – 9 GENERAL SAFETY PRECAUTIONS Locking nut A locking nut is used to secure some types of cutting attachment. When fi tting, tighten the nut in the opposite direction to the direction of rotation of the cutting attachment. To remove it, undo the nut in the same direction as the cutting attach...
Page 10 - ASSEMBLY; Fitting the loop handle
10 – English ASSEMBLY Fitting the loop handle (325Cx) • Position the handle on the shaft. Note that the handle must be mounted below the arrow on the shaft. • Fit the screw, securing plate and wing nut as shown in the diagram. • Tighten the wing nut. Fitting the loop handle (323L) • Clip the loop ha...
Page 12 - FUEL HANDLING; Fuel safety; Transport and storage; Fuel; Gasoline
12 – English FUEL HANDLING Fuel safety Never start the machine: 1 If you have spilt fuel on it. Wipe off the spillage and allow remaining fuel to evaporate. 2 If you have spilt fuel on yourself or your clothes, change your clothes. Wash any part of your body that has come in contact with fuel. Use s...
Page 13 - Mixing; Fueling
English – 13 FUEL HANDLING Mixing • Always mix the gasoline and oil in a clean container intended for fuel. • Always start by fi lling half the amount of the gasoline to be used. Then add the entire amount of oil. Mix (shake) the fuel mixture. Add the remaining amount of gasoline. • Mix (shake) the ...
Page 14 - STARTING AND STOPPING; Check before starting
14 – English STARTING AND STOPPING Check before starting • Never start the machine indoors. Exhaust fumes can be dangerous if inhaled. • Observe your surroundings and make sure that there is no risk of people or animals coming into contact with the cutting equipment. • Place the machine on the groun...
Page 15 - Starting and stopping; Starting; Stopping
English – 15 STARTING AND STOPPING Starting and stopping Starting Primer bulb: Press the primer bulb repeatedly until fuel begins to fi ll the bulb. The bulb need not be completely fi lled. Choke: Set the choke control in the choke position. Hold the body of the machine on the ground using your left...
Page 16 - WORKING TECHNIQUES; General working instructions; Basic safety rules
16 – English WORKING TECHNIQUES General working instructions Basic safety rules 1 Look around you: • To ensure that people, animals or other things cannot affect your control of the machine. • To ensure that people, animals, etc., do not come into contact with the cutting attachment or loose objects...
Page 18 - MAINTENANCE; Carburetor; Function; Conditions
18 – English MAINTENANCE Carburetor Your Husqvarna product has been designed and manufactured to speci fi cations that reduce harmful emissions. After the engine has used 8-10 tanks of fuel the engine will be run-in. To ensure that it continues to run at peak performance and to minimise harmful exha...
Page 19 - Fine adjustment of the idle speed T; Muf
English – 19 MAINTENANCE Fine adjustment of the idle speed T Adjust the idle speed using the idle adjustment screw T, if it is necessary to readjust. First turn the idle adjustment screw T clockwise until the cutting attachment starts to rotate. Then turn the screw anticlockwise until the cutting at...
Page 20 - Cooling system; Spark plug; Air; Cleaning the air; Oiling the air
20 – English MAINTENANCE Cooling system To keep the working temperature as low as possible the machine is equipped with a cooling system. The cooling system consists of: 1 Air intake on the starter. 2 Fins on the fl ywheel. 3 Cooling fi ns on the cylinder. 4 Cylinder cover (directs cold air over the...
Page 21 - Bevel gear
English – 21 MAINTENANCE Bevel gear (323L) The bevel gear is fi lled with the right quantity of grease at the factory. However, before using the machine you should check that the bevel gear is fi lled three-quarters full with grease. Use HUSQVARNA special grease. The grease in the bevel gear does no...
Page 22 - Maintenance schedule
22 – English MAINTENANCE Maintenance schedule The following is a list of the maintenance that must be performed on the machine. Most of the items are described in the Maintenance section. Maintenance Daily maintenance Weekly maintenance Monthly maintenance Clean the outside of the machine. X Make su...
Page 23 - TECHNICAL DATA; Technical data
English – 23 TECHNICAL DATA Technical data Note 1: Equivalent noise pressure level is calculated as the time-weighted energy total for noise pressure levels under various working conditions with the following time distribution: 1/2 idle and 1/2 max. speed. NOTE! Noise pressure at the user’s ear and ...
Page 25 - FEDERAL EMISSION CONTROL WARRANTY STATEMENT
English – 25 FEDERAL EMISSION CONTROL WARRANTY STATEMENT YOUR WARRANTY RIGHTS AND OBLIGATIONS The EPA (The US Environmental Protection Agency), Environment Canada and Husqvarna Forest & Garden are pleased to explain the emissions control system warranty on your 2001 and later small nonroad engin...
Page 31 - Trimmy VII
6" 2) 1) ~ 15 cm 6" 7 8 9 10 11 15 cm 1 2 3 4 5 6 7,0 m 23" 2,0- mm , 080-." 12 cm 5" ~ 3,5 m 11" Trimmy VII
