Page 2 - I. GENERAL OPERATION; SAFETY RULES; Safe Operation Practices for Ride-On Mowers; WARNING
2 I. GENERAL OPERATION • Read, understand, and follow all instructions on the machine and in the manual before starting. • Do not put hands or feet near rotating parts or under the machine. Keep clear of the discharge opening at all times. • Only allow responsible adults, who are familiar with the i...
Page 3 - SAFE HANDLING OF GASOLINE
3 • Be sure the area is clear of bystanders before operat- ing. Stop machine if anyone enters the area. • Never carry passengers.• Do not mow in reverse unless absolutely necessary. Al ways look down and behind before and while backing. • Never carry children, even with the blades shut off. They may...
Page 4 - TABLE OF CONTENTS; PRODUCT SPECIFICATIONS; CONGRATULATIONS; CUSTOMER RESPONSIBILITIES
4 SAFETY RULES ......................................................... 2-3 PRODUCT SPECIFICATIONS ....................................... 4 CUSTOMER RESPONSIBILITIES ................................. 4 ASSEMBLY ................................................................. 5-6 OPERATION ..........
Page 5 - UNASSEMBLED PARTS; Slope Sheet; ASSEMBLY; TOOLS REQUIRED FOR ASSEMBLY; TO REMOVE TRACTOR FROM CARTON; UNPACK CARTON; BEFORE REMOVING TRACTOR FROM
5 UNASSEMBLED PARTS (2) Keys Slope Sheet Key (1) Oil Drain Tube ASSEMBLY Your new tractor has been assembled at the factory with the exception of those parts left unassembled for shipping purposes. Fig. 2 Fig. 1 ADJUST SEAT (See Fig. 2) • Sit in seat.• Lift up adjustment lever (A) and slide seat unt...
Page 6 - CHECKLIST
6 ASSEMBLY CHECK TIRE PRESSURE The tires on your tractor were overinflated at the factory for shipping purposes. Correct tire pressure is important for best cutting performance.• Reduce tire pressure to PSI shown on tires. CHECK DECK LEVELNESS For best cutting results, mower housing should be proper...
Page 7 - OPERATION
7 OPERATION These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning. DANGER, KEEP HANDS AND FEET AWAY FREE WHEEL (Automatic Models only) KEEP AREA CLEAR SLOPE HAZARDS 15 15 (SEE SAFETY RULES SECTION) BATTERY REVERSE FORWARD FAST SLOW EN...
Page 8 - KNOW YOUR TRACTOR; POSITION
8 OPERATION KNOW YOUR TRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and ad just ments. Save this manual for future reference. Our tractors conform to the appli...
Page 9 - HOW TO USE YOUR TRAC TOR
9 OPERATION The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye dam age. Always wear safety glass es or eye shields while operating your tractor or per form ing any ad just ments or repairs. We rec om mend standard safety glasses or a wide ...
Page 10 - TO ADJUST MOWER CUT TING HEIGHT
10 OPERATION TO ADJUST MOWER CUT TING HEIGHT (See Fig. 8) The po si tion of the at tach ment lift le ver (A) de ter mines the cut ting height. • Put attachment lift lever in desired cutting height slot. A TO USE CRUISE CONTROL (J) (See Fig. 7) The cruise control feature can be used for forward trave...
Page 11 - TO OPERATE ON HILLS; TO STOP MOWER BLADES
11 Fig. 10 OPERATION Fig. 12 TO TRANSPORT (See Figs. 3 and 12) When pushing or towing your tractor, be sure to disengage transmission by placing freewheel control in free wheel ing po si tion. Free wheel control is located at the rear drawbar of tractor.• Raise attachment lift to highest position wi...
Page 12 - ADD GASOLINE; BEFORE STARTING THE ENGINE; CHECK ENGINE OIL LEVEL; TOWING CARTS AND OTHER AT TACH MENTS; SERVICE REMINDER/HOUR METER
12 CAUTION: Alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to sep a ra tion and for ma tion of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied ...
Page 13 - MOWING TIPS; Always operate engine at full throttle when mow-; PURGE TRANSMISSION; CAUTION: Never engage or disengage; movement of the drive wheels.
13 Fig. 13 MOWING TIPS • Mower should be properly leveled for best mowing performance. See “TO LEVEL MOWER HOUSING” in the Service and Adjustments section of this manual. • The left hand side of mower should be used for trim- ming. • Drive so that clippings are discharged onto the area that has been...
Page 14 - MAINTENANCE; GENERAL RECOMMENDATIONS; BEFORE EACH USE; LUBRICATION CHART
14 MAINTENANCE T RAC T 0 R Inspect Muffler/Spark Arrester Clean Air Filter Change Engine Oil (with oil filter) Replace Air Filter Paper Cartridge Replace Spark Plug Check Engine Oil Level Clean Engine Cooling Fins Clean Air Screen 1 - Change more often when operating under a heavy load or in high am...
Page 15 - TRACTOR; BLADE CARE
15 MAINTENANCE TRACTOR Always observe safety rules when per form ing any main te nance. BRAKE OPERATION If tractor requires more than five (5) feet to stop at highest speed in high est gear on a level, dry concrete or paved surface, then brake must be checked and ad just ed. (See “TO CHECK BRAKE” in...
Page 16 - ENGINE
16 MAINTENANCE V-BELTS Check V-belts for deterioration and wear after 100 hours of operation and replace if necessary. The belts are not ad just able. Re place belts if they begin to slip from wear. TRANSAXLE COOLING The transmission fan and cooling fins should be kept clean to assure proper cooling...
Page 17 - MUFFLER; CLEANING
17 MAINTENANCE MUFFLER Inspect and replace corroded muffler and spark arrester (if equipped) as it could create a fire hazard and/or dam- age. SPARK PLUGS Replace spark plugs at the beginning of each mowing season or after every 100 hours of operation, whichever occurs first. Spark plug type and gap...
Page 18 - SERVICE AND ADJUSTMENTS
18 WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SER VICE OR AD JUST MENTS: • Depress brake pedal fully and set parking brake. • Place attachment clutch in “DISENGAGED” position. • Turn ignition key to “STOP” and remove key. • Make sure the blades and all moving parts have completely stopp...
Page 20 - your hands with gloves and/or wrap; TO LEVEL MOWER; NOTE
20 SERVICE AND ADJUSTMENTS • If adjustment is necessary, see step in Visual Adjust- ment instructions above. • Recheck measurements, adjust if necessary until both sides are equal. FRONT-TO-BACK ADJUSTMENT (See Figs. 28 & 29) IMPORTANT: Deck must be level side-to-side. To obtain the best cutting...
Page 21 - TO REPLACE MOWER BLADE DRIVE BELT; TO REPLACE MOTION DRIVE BELT
21 Fig. 30 Fig. 31 TO REPLACE MOWER BLADE DRIVE BELT (See Fig. 30) The mower blade drive belt may be replaced without tools. Park the tractor on level surface. Engage parking brake. BELT REMOVAL - • Remove mower from tractor (See “TO REMOVE MOW ER” in this section of manual). • Work belt off both ma...
Page 22 - TO START ENGINE WITH A WEAK BATTERY; TO REMOVE WHEEL FOR REPAIRS
22 Fig. 32 RE TAIN ING RING WASH ERS SQUARE KEY (REAR WHEEL ONLY) AXLE COVER TO START ENGINE WITH A WEAK BATTERY (See Fig. 33) WARNING : Lead-acid batteries gen- er ate ex plo sive gases. Keep sparks, flame and smoking ma te ri als away from bat ter ies. Always wear eye pro tec tion when around batt...
Page 23 - TO REMOVE HOOD AND GRILL ASSEMBLY; TO AD JUST THROTTLE CON TROL CABLE; TRANSMISSION; REMOVAL/RE PLACE MENT; nals by allowing a wrench or any other
23 TO REMOVE HOOD AND GRILL ASSEMBLY (See Fig. 35) • Raise hood. • Unsnap headlight wire connector.• Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor. • To replace, reverse above procedure. ENGINE TO AD JUST THROTTLE CON TROL CABLE The throttle control has b...
Page 24 - STORAGE; WARNING: Never store the trac tor with; BATTERY; FUEL SYSTEM; ENGINE OIL; OTHER
24 STORAGE Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more. WARNING: Never store the trac tor with gas o line in the tank inside a building where fumes may reach an open flame or spark. Allow the engine to cool before stori...
Page 25 - TROUBLESHOOTING POINTS; PROBLEM
25 TROUBLESHOOTING POINTS Will not start 1. Out of fuel. 1. Fill fuel tank. 2. Engine not “CHOKED” properly. 2. See “TO START ENGINE” in Operation section. 3. Engine flooded. 3. Wait several minutes before attempting to start. 4. Bad spark plug. 4. Replace spark plug. 5. Weak or dead battery. 5. Rec...
Page 27 - SCHEMATIC
27 TRACTOR - - MODEL NUMBER YTH20K46 (96045001800), PRODUCT NO. 960 45 00-18 SCHEMATIC M FUSE STARTER SOLENOID BATTERY CLUTCH/BRAKE (PEDAL UP) REVERSE SWITCH (NOT IN REVERSE) SEAT SWITCH (NOT OCCUPIED) SHORTING CONNECTOR CHASSIS HARNESS IGNITION UNIT HOUR METER CHASSIS HARNESS CONNECTOR (MATING SIDE...
Page 28 - ELECTRICAL
28 TRACTOR - - MODEL NUMBER YTH20K46 (96045001800), PRODUCT NO. 960 45 00-18 ELECTRICAL 30 33 34 90 22 79 21 41 42 26 8 1 99 100 91 2 27 43 27 24 40 71 28 55 16 87 With 12V Outlet Option 59 103 With Service Minder Option 46 46 25 T03S 29 141
Page 29 - KEY PART
29 TRACTOR - - MODEL NUMBER YTH20K46 (96045001800), PRODUCT NO. 960 45 00-18 ELECTRICAL KEY PART NO. NO. DESCRIPTION 1 532 16 34-65 Battery 2 874 76 04-12 Bolt Hex Head 1/4-20 x 3/4 8 532 41 41-26 Box Battery 16 532 17 61-38 Switch Interlock Push-In 21 532 18 37-59 Harness Socket Light w/4152J 22 53...
Page 30 - CHASSIS
30 TRACTOR - - MODEL NUMBER YTH20K46 (96045001800), PRODUCT NO. 960 45 00-18 CHASSIS 182 68 68 68 68 176 176 175 178 183 183 236 236 150 34 130 130 177 chassis-tex_TEX GT HUSQ_57 235 235 37 194 194 181 181 162 196 287 138 36 36 195 14 214 130 176 202 203 204 210 208 18 15 25 207 211 209 212 5 176 17...
Page 32 - DRIVE
32 TRACTOR - - MODEL NUMBER YTH20K46 (96045001800), PRODUCT NO. 960 45 00-18 DRIVE 185 161 185 51 231 170 183 205 205 drive-tex_T2_pedal_11 2 1 2 37 33 73 73 99 116 116 186 189 49 187 50 51 190 52 51 64 188 35 184 167 160 42 221 210 211 166 211 17 214 215 153 153 222 29 15 159 159 116 163 56 114 122...
Page 34 - SPARK ARRESTER KIT
34 1 12 42 9 SPARK ARRESTER KIT 92 45 85 90 29 21 20 94 95 69 engine-tex_Kohl_14 2 81 82 87 91 18 15 37 28 37 TRACTOR - - MODEL NUMBER YTH20K46 (96045001800), PRODUCT NO. 960 45 00-18 ENGINE 28 113 110 109 111
Page 37 - STEERING
37 KEY PART NO. NO. DESCRIPTION 1 532 42 34-69 Wheel, Steering (HUSQ SR) 2 532 19 59-68 Axle Cast Iron 4 532 40 30-87 Spindle Asm., LH 5 532 40 30-88 Spindle Asm., RH 6 532 12 49-31 Washer, Thrust 7 532 12 17-48 Washer 25/32 x 1-5/8 x 16 Ga. 8 812 00 00-29 Ring, Klip #T5304-75 9 532 12 12-32 Cap, Sp...
Page 38 - DECALS; WHEELS AND TIRES
38 TRACTOR - - MODEL NUMBER YTH20K46 (96045001800), PRODUCT NO. 960 45 00-18 DECALS NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm KEY PART NO. NO. DESCRIPTION 6 2 1 3 11 4 10 5 9 8 7 wheel_art_1-tex WHEELS AND TIRES KEY PART NO. NO. DESCRIPTION KEY PART NO. NO. DESCRIPTION 1 5...
Page 39 - SEAT ASSEMBLY
39 TRACTOR - - MODEL NUMBER YTH20K46 (96045001800), PRODUCT NO. 960 45 00-18 SEAT ASSEMBLY 1 532 40 66-21 Seat 2 532 18 01-66 Bracket Pivot Fender 3 532 14 06-75 Strap, Asm Fender 6 873 80 06-00 Nut, Lock w/Ins. 3/8-16 unc 7 532 12 41-81 Spring, Seat Cprsn 8 532 17 18-77 Bolt 5/16-18 unc x 3/4 w/Sem...
Page 40 - MOWER DECK
40 TRACTOR - - MODEL NUMBER YTH20K46 (96045001800), PRODUCT NO. 960 45 00-18 MOWER DECK 30 43 42 60 38 63 46 147 55 64 30 32 31 33 200 34 56 57 59 40 188 1 69 69 199 40 145 15 14 21 26 27 198 29 21 21 68 23 24 144 36 240 57 19 19 6 6 195 122 123 195 189 113 113 47 189 188 21 21 69 69 69 21 30 38 56 ...
Page 41 - KEY PART
41 TRACTOR - - MODEL NUMBER YTH20K46 (96045001800), PRODUCT NO. 960 45 00-18 MOWER DECK KEY PART NO. NO. DESCRIPTION NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm 1 532 41 08-63 Mower Housing 2 532 40 55-06 Cover Mandrel RH 3 532 40 55-07 Cover Mandrel LH 6 532 19 51-86 Arm Su...
Page 42 - MOWER LIFT
42 TRACTOR - - MODEL NUMBER YTH20K46 (96045001800), PRODUCT NO. 960 45 00-18 MOWER LIFT 7 3 87 10 88 2 89 90 87 98 97 97 lift-tex_16_r3 91 87 100 89 87 101* *Key 91 may be substituted for Key 101 2 532 19 52-23 Shaft Asm., Lift 3 532 19 52-31 Lever Asm., Lift RH 7 532 41 15-55 Grip, Lever 10 532 19 ...
Page 43 - SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION; WARNING: To avoid serious injury, operate your tractor up and
43 15 DEGREES MAX. FOLD ALONG DOTTED LINE THIS IS A 15 DEGREE SLOPE ONLY RIDE UP AND DOWN HILL, NOT ACROSS HILL SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION WARNING: To avoid serious injury, operate your tractor up and down the face of slopes, never across the face. Do not mow slopes great...
