Husqvarna 45-0352 - Manual - manualsarea.com

Page 2 - Stay off of steep slopes.; SAFETY RULES; CARTON CONTENTS

2 Any power equipment can cause injury if operated improperly or if the user does not understand how to operate the equipment. Exercise caution at all times, when using power equipment. 1. Read the vehicle and sweeper owners manuals and know how to operate your vehicle and sweeper before using this ...

Page 4 - ASSEMBLY OF SWEEPER

4 STEP 4 - CONNECT HITCH TUBES 6. Fasten the hitch tubes together using two 5/16" x 3" hex bolts and 5/16" nylock nuts. Do not tighten yet. See ﬁ gure 2. FIGURE 1 FIGURE 2 FIGURE 3 STEP 5 - ASSEMBLE HITCH PIN 7. Assemble the hitch pin bracket , the hitch spring and then the 7/16" ﬂ a...

Page 5 - STEP 7a - ASSEMBLE HITCH BRACKETS; HANDLE

5 STEP 8 - TIGHTEN BOLTS 14. At this time tighten the four bolts in ﬁ gure 1 that fasten the hitch tubes to the sweeper housing. Next, tighten the two bolts in ﬁ gure 2 that fasten the ends of the hitch tubes together. Finally, tighten the two bolts in ﬁ gure 4 or 5 that fasten the hitch brackets to...

Page 6 - FIGURE 8; Assemble the extension spring onto the end of the upper; FIGURE 9; Place the height adjust strap between the angle bracket; Do not tighten yet. See; Attach the height adjust strap to the height adjust handle

6 FIGURE 8 STEP 11 - ASSEMBLE EXTENSION SPRING 18. Assemble a 5/16" x 1" hex bolt and a 5/16" nylock nut into the top hole in the height adjustment handles. See ﬁ gure 8. 19. Assemble the extension spring onto the end of the upper bolt and the middle bolt in the height adjust handles. As...

Page 7 - ASSEMBLY OF HOPPER BAG; STEP 15 - ASSEMBLE UPPER TUBES; starting at the center cut out; inside; STEP 16 - ASSEMBLE LOWER TUBES

7 ASSEMBLY OF HOPPER BAG STEP 15 - ASSEMBLE UPPER TUBES 1. Insert the left hand upper hopper tube through the stitched ﬂ aps of the hopper bag, starting at the center cut out in the top of the bag. See ﬁ gures 12, 13 and 14. Repeat for the right hand upper hopper tube. FIGURE 12 FIGURE 15 2. Slide t...

Page 8 - STEP 19 - ASSEMBLE SUPPORT RODS; Assemble the two hopper support rods as shown in; STEP 18 - ATTACH BAG SIDES; Fold the bag fl aps around the lower hopper tubes and; STEP 17 - ATTACH BAG BOTTOM; Assemble the bag retainer and the bag frame strap to the; BAG FRAME STRAP; Assemble the bag frame strap to the holes in the lower

8 STEP 19 - ASSEMBLE SUPPORT RODS IMPORTANT: Do not over bend the support rods during the following step. Over bending will decrease the supporting tension of the rods. 10. Assemble the two hopper support rods as shown in ﬁ gure 20. Place the ends of the rods into the holes in the upper and lower ho...

Page 9 - HINT: To ease assembly of the palnuts, place the bag on

9 FIGURE 22 STEP 22 - ATTACH HOPPER BAG 17. To attach the hopper bag to the sweeper, slide the ends of the bag arm tubes into the ends of the hitch tubes and secure with two 1/4" x 1-3/4" clevis pins and small hairpin cotters. See ﬁ gure 25. STEP 21 - ATTACH ROPE 16. Secure the rope to the c...

Page 10 - STEP 22 - ATTACH SWEEPER TO TRACTOR; Place the tractor and sweeper on a fl at level surface.

10 STEP 22 - ATTACH SWEEPER TO TRACTOR FIGURE 26 1. Place the tractor and sweeper on a ﬂ at level surface. 2. Set the sweeper height adjustment handle to about the middle of its adjustment range. 3. Attach the sweeper hitch to the tractor hitch, arranging the hitch spacers in one of six possible com...

Page 11 - KNOW YOUR SWEEPER; Never attach the hopper rope to any; HOW TO USE YOUR SWEEPER; OPERATION

11 KNOW YOUR SWEEPER CAUTION: Ke e p swe e p e r away f r o m f i r e. Excessive heat can damage the brushes and hopper bag and could cause the bag and its contents to burn. CAUTION: Never attach the hopper rope to any part of your body or clothing! Never hold onto the rope while towing the sweeper!...

Page 12 - SCHEDULED MAINTENANCE; Before storing the sweeper,; CLEANING; MAINTENANCE

12 FIGURE 28 4. Lubricate the wheel bearings each season. Remove the hub cap and apply a few drops of light weight oil. 5. Every two years, remove the wheels and clean the gears found inside the wheel housing. After cleaning, lubricate the gears with an even coat of light grease. To remove the wheel...

Page 13 - BRUSH REPLACEMENT; NOTE: Brush replacement should be done one brush at; SERVICE AND ADJUSTMENTS; Make notes on the position; TROUBLESHOOTING

13 BRUSH REPLACEMENT NOTE: Brush replacement should be done one brush at a time. 1. Remove the hopper bag from the sweeper.2. Loosen only the two hex bolts and lock nuts which clamp one brush in a brush retainer. Do not loosen or remove the bolts which fasten the brush retainers to the brush shaft. ...

Page 15 - the; fastest way to purchase parts

15 REF. PART QTY. DESCRIPTION REF. PART QTY. DESCRIPTION REF. PART QTY. DESCRIPTION NO. NO. NO. NO. NO. NO. 46 43938 2 Rod, Hopper Support 34" 46 43938 2 Rod, Hopper Support 34" 46 43938 2 Rod, Hopper Support 34" 46 43938 2 Rod, Hopper Support 34" 47 43737 1 Hopper Rope 47 43737 1 Ho...

Page 16 - REPAIR PARTS