Page 2 - KEY TO SYMBOLS
2 – English KEY TO SYMBOLS Symbols WARNING! Clearing saws, brushcutters and trimmers can be dangerous! Careless or incorrect use can result in serious or fatal injury to the operator or others. Please read the operator’s manual carefully and make sure you understand the instructions before using the...
Page 3 - CONTENTS
English – 3 CONTENTS Contents Note the following before starting: Husqvarna AB has a policy of continuous product development and therefore reserves the right to modify the design and appearance of products without prior notice. Maintenance, replacement, or repair of the emission control devices and...
Page 4 - SAFETY INSTRUCTIONS; Personal protective equipment; Throttle lock
4 – English SAFETY INSTRUCTIONS Personal protective equipment GLOVES Gloves should be worn when necessary, e.g., when fitting cutting attachments. HEARING PROTECTION Wear hearing protection that provides adequate noise reduction. EYE PROTECTION Always wear approved eye protection. If you use a visor...
Page 5 - Vibration damping system; Muffler; Locking nut
English – 5 SAFETY INSTRUCTIONS Vibration damping system Your machine is equipped with a vibration damping system that is designed to minimise vibration and make operation easier. Use of incorrectly wound cord or an incorrect cutting attachment increases the level of vibration. The machine ′ s vibra...
Page 6 - s safety equipment
6 – English SAFETY INSTRUCTIONS Checking, maintaining and servicing the machine ′ s safety equipment Throttle lock • Make sure the throttle control is locked at the idle setting when the throttle lock is released. • Press the throttle lock and make sure it returns to its original position when you r...
Page 8 - Cutting equipment; Trimmer head; General safety precautions
8 – English SAFETY INSTRUCTIONS Cutting equipment Sharpening grass cutters and grass blades • See the cutting attachment packaging for correct sharpening instructions. • Sharpen blades and cutters using a single-cut flat file. • Sharpen all edges equally to maintain the balance of the blade. Trimmer...
Page 9 - Starting; Transport and storage
English – 9 SAFETY INSTRUCTIONS Starting • The complete clutch cover and shaft must be fitted before the machine is started, otherwise the clutch can come loose and cause personal injury. • Never start the machine indoors. Exhaust fumes can be dangerous if inhaled. • Observe your surroundings and ma...
Page 10 - General working instructions; Basic safety rules; Basic working techniques; Terms; Grass clearing using a grass blade
10 – English SAFETY INSTRUCTIONS General working instructions Basic safety rules 1 Look around you: • To ensure that people, animals or other things cannot affect your control of the machine. • To ensure that people, animals, etc., do not come into contact with the cutting attachment or loose object...
Page 12 - What is what on the trimmer?
12 – English WHAT IS WHAT? What is what on the trimmer? = 28 29 30 = 27 ¢ ¥ 1 Trimmer head 2 Grease filler cap 3 Bevel gear 4 Cutting attachment guard 5 Shaft 6 Loop handle 7 Throttle control 8 Stop switch 9 Throttle lock 10 Cylinder cover 11 Starter handle 12 Fuel tank 13 Choke control 14 Air purge...
Page 13 - ASSEMBLY; Fitting the J-handle; Fitting blades and trimmer heads
English – 13 ASSEMBLY Fitting the J-handle • Clip the loop handle onto the shaft. Note that the loop handle must be fitted between the arrows on the shaft. • Slide the spacer into the slot in the loop handle. • Fit the nut, knob and screw. Do not overtighten. • Attach the J-handle to the loop handle...
Page 15 - FUEL HANDLING; Fuel; Gasoline; Mixing; Fuelling
English – 15 FUEL HANDLING Fuel CAUTION! The machine is equipped with a two-stroke engine and must always been run using a mixture of gasoline and two-stroke engine oil. It is important to accurately measure the amount of oil to be mixed to ensure that the correct mixture is obtained. When mixing sm...
Page 16 - STARTING AND STOPPING; Check before starting; Cold engine
16 – English STARTING AND STOPPING Check before starting For safety reasons follow these recommendations! • Check the blade to ensure that no cracks have formed at the bottom of the teeth or by the centre hole. The most common reason why cracks are formed is that sharp corners have been formed at th...
Page 17 - Stopping
English – 17 STARTING AND STOPPING Air purge: Press the air purge diaphragm repeatedly until fuel begins to fill the diaphragm. The diaphragm need not be completely filled. Stopping Stop the engine by switching off the ignition. Starting Hold the body of the machine on the ground using your left han...
Page 18 - MAINTENANCE; Carburettor
18 – English MAINTENANCE Carburettor Your Husqvarna product has been designed and manufactured to specifications that reduce harmful emissions. After the engine has used 8-10 tanks of fuel the engine will be run-in. To ensure that it continues to run at peak performance and to minimise harmful exhau...
Page 19 - High speed jet H
English – 19 MAINTENANCE will run smoothly in every position. The idle speed should also be well below the speed at which the cutting attachment starts to rotate. IMPORTANT! If the idle speed cannot be adjusted so that the cutting attachment stops, contact your dealer/service workshop. Do not use th...
Page 20 - Cooling system; Cleaning the air filter; Oiling the air filter
20 – English MAINTENANCE Cooling system To keep the working temperature as low as possible the machine is equipped with a cooling system. The cooling system consists of: 1 Air intake on the starter. 2 Fins on the flywheel. 3 Cooling fins on the cylinder. 4 Cylinder cover (directs cold air over the c...
Page 21 - Bevel gear; Daily maintenance
English – 21 MAINTENANCE Bevel gear The bevel gear is filled with the right quantity of grease at the factory. However, before using the machine you should check that the bevel gear is filled three-quarters full with grease. Use HUSQVARNA special grease. The grease in the bevel gear does not normall...
Page 22 - TECHNICAL DATA; Technical data
22 – English TECHNICAL DATA Technical data NOTE! Noise pressure at the user’s ear and vibration on the handles are measured with all the machine’s approved cutting equipment fitted. The table indicates the highest and lowest values. Note 1: Equivalent noise pressure level is calculated as the time-w...
Page 23 - FEDERAL EMISSION CONTROL WARRANTY STATEMENT
English – 23 FEDERAL EMISSION CONTROL WARRANTY STATEMENT YOUR WARRANTY RIGHTS AND OBLIGATIONS The EPA (The US Environmental Protection Agency), Environment Canada and Husqvarna Forest & Garden are pleased to explain the emissions control system warranty on your 2001 and later small nonroad engin...
Page 25 - Tri Cut
1 Tri Cut 2 3 4 5 6 7 8 <20mm >20mm ! B A 6 Nm X 10
Page 26 - Trimmy H II
1 Trimmy H II 2 3 4 5 6 7 8 9 7,5 m 25' 2,0-2,4 mm .080-.095" 1 2 15 cm 6" ~ 3,7 m 12' 15 cm 6"
Page 27 - Trimmy Hit; “Click”
1 Trimmy Hit 2 3 4 5 6 7 8 9 10 11 “Click” “Click” 7,0 m 23' " 12 cm 5" ~ 3,5 m 11' 15 cm 6 " " 2,0-2,4 mm .080-.095 ~ 15 cm 6
Page 28 - Trimmy Hit Pro
1 Trimmy Hit Pro 2 5 6 7 8 9 10 12 “Click” 3 4 7,5 m 25' 2,0-2,4 mm .080-.095" 15 cm 6" ~ 3,7 m 12' 1.) 2.) 11 15 cm 6" 15 cm 6"
