Page 2 - EXPLANATION OF SYMBOLS; Symbols
2 – English EXPLANATION OF SYMBOLS Symbols WARNING! The edger can be dangerous!Careless or incorrect use can result in serious or fatal injury to the operator or others. Always use:• A protective helmet where there is a risk of falling objects. • Ear protection• Approved eye protection Read through ...
Page 3 - CONTENTS; List of Contents
English – 3 CONTENTS List of Contents EXPLANATION OF SYMBOLS Symbols ................................................................................2 CONTENTS List of Contents .....................................................................3 SAFETY INSTRUCTIONS Personal protective equipment .....
Page 4 - SAFETY INSTRUCTIONS; Personal protective equipment; The machine
4 – English SAFETY INSTRUCTIONS Personal protective equipment IMPORTANT INFORMATION • An edger used incorrectly or carelessly can become a dangerous tool, that can cause serious or fatal injury to the operator or others. It is extremely important that you read and understand the content of this manu...
Page 6 - s safety equipment
6 – English SAFETY INSTRUCTIONS IMPORTANT INFORMATION • All service and repairs to the machine require special training. • This applies especially to the machine ʼ s safety equipment. If the machine does not meet any of the controls listed below you should contact your serv-ice workshop. • The purch...
Page 8 - General safety instructions; Safety instructions before starting work
8 – English General safety instructions SAFETY INSTRUCTIONS IMPORTANT INFORMATION • The machine is only designed for cutting the edges of lawns. • The only accessories to be used with the engine unit as a drive source are the cutting units we recommend in the chapter “Technical data”. • The operator...
Page 9 - Transport and storage; Start
English – 9 SAFETY INSTRUCTIONS Transport and storage • Store and transport the machine and fuel so that any leakage or fumes do not risk coming into contact with sparks or naked fl ames. For example, electric machines, electric motors, elec- trical switches/power switches, heaters or the like. • Wh...
Page 10 - General working instructions; Basic safety precautions; Basic working techniques; Safety instructions while working
10 – English SAFETY INSTRUCTIONS General working instructions IMPORTANT INFORMATION • This section takes up the basic safety precautions for working with the edger. • If you encounter a situation where you are uncertain how to proceed you should ask an expert. Contact your dealer or your service wor...
Page 11 - Safety instructions after completing work
English – 11 SAFETY INSTRUCTIONS Safety instructions after completing work • Ensure the blade has stopped before cleaning, car-rying out repairs or an inspec-tion. Remove the spark plug cable from the spark plug. • Wear heavy-duty gloves when carrying out repairs on the edger. • Store the machine ou...
Page 12 - What is what on the edger?
12 – English WHAT IS WHAT? What is what on the edger? 1. Blade 2. Grease fi ller cap 3. Angle gear 4. Blade guard 5. Shaft 6. Loop handlebar 7. Throttle 8. Stop switch 9. Throttle trigger lock 10. Cylinder cover 11. Starter handle 12. Fuel tank 13. Choke 14. Air purge 15. Air fi lter cover 16. Clutc...
Page 13 - Assembling the blade; ASSEMBLY; Assembling the loop handlebar
English – 13 Assembling the blade ASSEMBLY Fit the blade as follows: 1. Fit the drive disc (A) on the outgoing shaft. Make sure that the edge that fi ts in the hole of the blade is facing outward. 2. Block the blade rotation by inserting locking pin in the hole behind the blade guard engaging it in ...
Page 14 - Fuel mixture; FUEL HANDLING; Petrol; Fuelling
14 – English Fuel mixture NOTE!The edger is fi tted with two-stroke engines and must always be run on a mixture of petrol and two-stroke oil. To ensure the correct mixture proportions it is important to measure the quantity of oil accurately. When mixing small amounts of fuel small discrepancies in ...
Page 15 - START AND STOP; Control before starting; Start and stop; STARTING
English – 15 START AND STOP Control before starting ! WARNING!When the engine is started with the choke lever in either the choke- or start throttle position the cutting equipment starts to rotate immediately. ! For reasons of safety follow these recommendations! • Check that the support fl ange is ...
Page 16 - Carburettor; MAINTENANCE
16 – English Carburettor Your Husqvarna product has been designed and manufactured to speci fi cations that reduce harmful emissions. After your unit has been run 8-10 tanks of fuel the engine has broken in. To ensure that your unit is at peak performance and producing the least amount of harmful em...
Page 17 - Final setting of the idling speed T; Correctly adjusted carburettor
English – 17 Final setting of the idling speed T Adjust the idling speed with the screw T, if it is necessary to readjust. First turn the idle speed adjusting screw T clockwise until the cutting attachment starts to rotate/move.Then turn, counter-clockwise until the cutting attachment stops. A corre...
Page 18 - Muf; Cooling system
18 – English MAINTENANCE Muf fl er with catalytic converter A muf fl er fi tted with a catalytic converter reduces the extent of the following substances in the exhaust fumes: • Hydrocarbons (HC). Some hydrocarbons in gasoline and the exhaust are carcinogenic. • Nitric oxides (NO). Irritating for th...
Page 20 - Maintenance schedule; Weekly maintenance; Daily maintenance
20 – English MAINTENANCE Maintenance schedule Below follows some general maintenance instructions. If you need further information please contact your service workshop. Weekly maintenance 1. Check the starter, the starter cord and the return spring. 2. Make sure that the vibration damping elements a...
Page 21 - Monthly maintenance
English – 21 MAINTENANCE Monthly maintenance I. Clean the fuel tank using petrol. 2. Clean the outside of the carburettor and the area surrounding it. 3. Clean the fan wheel and the area around it. 4. Check the fuel fi lter and the fuel pipe, replace if necessary. 5. Check all cables and connections...
Page 22 - TECHNICAL DATA; Technical data
22 – English TECHNICAL DATA Technical data Engine Displacement, cu. in/cm 3 Cylinder bore, inch/mmStroke length, inch/mmRecommended max. speed, rpmIdling speed, rpmSpeed of output shaft, rpmMax. engine output acc. to ISO 8893Catalytic converter muf fl er Speed-regulated ignition system Ignition syst...
Page 23 - EC-declaration of conformity
English – 23 EC-declaration of conformity (Applies to Europe only) We, Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel. +46 36-146500, declare under sole responsibility that the edger Husqvarna 323E and 325E X-series from the serial numbers of 2002 and onwards (the year is clearly stated in plain tex...
