Page 2 - KEY TO SYMBOLS; Symbols on the machine:; Symbols in the operator’s manual:
2 – English KEY TO SYMBOLS Symbols on the machine: WARNING! The machine can be a dangerous tool if used incorrectly or carelessly, which can cause serious or fatal injury to the operator or others. Please read the operator’s manual carefully and make sure you understand the instructions before using...
Page 3 - CONTENTS; Contents
English – 3 CONTENTS Contents KEY TO SYMBOLS Symbols on the machine: ............................................. 2 Symbols in the operator’s manual: ............................... 2 CONTENTS Contents ...................................................................... 3 WHAT IS WHAT? What is wh...
Page 4 - What is what on the power cutter - K3000?
4 – English WHAT IS WHAT? What is what on the power cutter - K3000? 1 2 3 4 5 6 7 8 10 11 12 14 15 9 6 13 1 Rear handle 2 Guard for the blade 14” 3 Cutting blade 4 Locking the axle 5 Front handle 6 Inspection covers 7 Power switch lock 8 Switch 9 Rating plate 10 Brush retainer 11 Carbon brushes 12 G...
Page 5 - What is what on the power cutter - K3000 Wet?
English – 5 WHAT IS WHAT? What is what on the power cutter - K3000 Wet? 1 Rear handle 2 Guard for the blade 3 Water kit 4 Cutting blade 5 Locking the axle 6 Front handle 7 Inspection covers 8 Power switch lock 9 Switch 10 Water tap 11 Water connection with flow limiter 12 Rating plate 13 Brush retai...
Page 6 - SAFETY INSTRUCTIONS; Personal protective equipment
6 – English SAFETY INSTRUCTIONS Steps before using a new power cutter • Please read the operator’s manual carefully and make sure you understand the instructions before using the machine. • The machine is only designed for cutting hard materials, such as concrete, brick, masonry as well as cast iron...
Page 7 - General safety warnings; Work area safety
English – 7 SAFETY INSTRUCTIONS General safety warnings Save all warnings and instructions for future reference. The term ”power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool. Work area safety • Keep work area clean and well lit. Cl...
Page 8 - Personal safety
8 – English SAFETY INSTRUCTIONS Personal safety • Stay alert, watch what you are doing and use common sense when operaing a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result i...
Page 9 - Switch; Power switch lock; Gradual start and overload protection; Guard for the blade
English – 9 SAFETY INSTRUCTIONS Machine ′′′′ s safety equipment This section describes the machine ′ s safety equipment, its purpose, and how checks and maintenance should be carried out to ensure that it operates correctly. See the ”What is what?” section to locate where this equipment is positione...
Page 10 - Cutting blades; General; Abrasive discs
10 – English SAFETY INSTRUCTIONS Cutting blades General • Cutting blades are available in two basic designs; abrasive discs and diamond blades. • High-quality blades are often most economical. Lower quality blades often have inferior cutting capacity and a shorter service life, which results in a hi...
Page 11 - Diamond blades; Transport and storage
English – 11 SAFETY INSTRUCTIONS Diamond blades Diamond blades consist of a steel body provided with segments that contain industrial diamonds. Diamond blades ensure lower costs per cutting operation, fewer blade changes and a constant cutting depth. When using diamond blades make sure that it rotat...
Page 12 - General working instructions; Cutting technique; How to avoid kickback
12 – English SAFETY INSTRUCTIONS General working instructions Cutting technique The technique described below is of a general character. Check information for each blade regarding individual cutting characteristics (for example, diamond blades requires less feeding pressure than an abrasive discs). ...
Page 14 - ASSEMBLY; Assembly
14 – English ASSEMBLY Assembly Fitting the cutting blade Husqvarna’s blades are approved for hand-held power cutters. Blades are manufactured with three different diameters of centre holes: 20 mm (0.787"), 22.2 mm (7/8") and 25.4 mm (1"). Bushings can be fitted on the machine axle to adj...
Page 15 - STARTING AND STOPPING; Before starting; Starting; Stopping
English – 15 STARTING AND STOPPING Before starting K3000 Wet Water connector • Connect the water hose to the water supply (A). The water is switched on and off with the water tap (B). Starting • Grip the front handle with the left hand. • Grip the rear handle with your right hand. • Press in the pow...
Page 16 - MAINTENANCE; Cooling system; Electrical Feed
16 – English MAINTENANCE General Cleaning Cooling system The machine is equipped with an efficient fan to cool the motor. Cooling air which is drawn in through the grille by the machines rear handle passes over the stator and rotor and out through the front of the motor housing. In order for the mac...
Page 17 - Bevel gear; Changing the grease; Daily maintenance
English – 17 MAINTENANCE Bevel gear The grease in the gear housing should be changed every 4 months. Use high quality gear grease The gear housing must not be filled completely with grease. The grease expands as the machine heats up during operation. If the gear housing was completely filled with gr...
Page 18 - TECHNICAL DATA; Cutting equipment
18 – English TECHNICAL DATA ´®z+TM"¶6}¨ ´®z+TM"¶6}¨ Note 1: Handle vibrations are measured according to ISO 8662-4 Cutting equipment Max. blade speed, rpm 4500 Recommended cable dimensions Technical data K3000 K3000 Wet Engine Protection class I I Ground fault circuit interrupter No Yes Rate...
Page 19 - EC-declaration of conformity
English – 19 TECHNICAL DATA EC-declaration of conformity (Applies to Europe only) Husqvarna AB , SE-433 81 Göteborg, Sweden, tel: +46-31-949000, declares under sole responsibility that the power cutter Husqvarna K3000, K3000 Wet dating from 2008 serial numbers and onwards (the year is clearly stated...
