Husqvarna 1152417-30 - Manual

Page 2 - KEY TO SYMBOLS; Symbols on the machine:; Symbols in the operator’s manual:

2 – English KEY TO SYMBOLS Symbols on the machine: WARNING! The machine can be a dangerous tool if used incorrectly or carelessly, which can cause serious or fatal injury to the operator or others. Please read the operator’s manual carefully and make sure you understand the instructions before using...

Page 3 - CONTENTS; Contents

English – 3 CONTENTS Contents KEY TO SYMBOLS Symbols on the machine: ............................................. 2 Symbols in the operator’s manual: ............................... 2 CONTENTS Contents ...................................................................... 3 PRESENTATION DM 340 .......

Page 4 - PRESENTATION; Softstart; Smartstart; Elgard; Speed control

4 – English PRESENTATION DM 340 It is our wish that you will be satisfied with your product and that it will be your companion for a long time. Think of this operator ′ s manual as a valuable document. By following its ′ content (using, service, maintenance etc) the life span and the second-hand val...

Page 5 - What is what on the drilling machine?

English – 5 WHAT IS WHAT? What is what on the drilling machine? 1 Drill spindle 2 Gearbox and motor module 3 Carrying handle 4 Gear knob 5 Quick mount, for Husqvarna stand 6 Water connector 7 LEDs for indicating power output 8 Switch 9 Smartstart TM 10 Inspection cover 11 Leakage hole 12 Inspection ...

Page 6 - SAFETY INSTRUCTIONS; Always use common sense; Personal protective equipment

6 – English SAFETY INSTRUCTIONS Steps before using a new drilling machine • Do not use the drilling machine without first reading and understanding the contents of this Operator’s Manual. • DM 340 is an electric stand drill, intended for drilling holes in concrete, bricks and various stone materials...

Page 7 - General safety precautions; Work area safety

English – 7 SAFETY INSTRUCTIONS General safety precautions Work area safety • Keep work area clean and well lit. Cluttered or dark areas invite accidents. • Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks whi...

Page 8 - Use and care; Transport and storage; General working instructions; Stand drilling; Drilling outdoors

8 – English SAFETY INSTRUCTIONS Use and care • Never use a machine that is faulty. Carry out the checks, maintenance and service instructions described in this manual. Some maintenance and service measures must be carried out by trained and qualified specialists. See instructions under the heading M...

Page 9 - Switch

English – 9 SAFETY INSTRUCTIONS Machine ′′′′ s safety equipment This section describes the machine ′ s safety equipment, its purpose, and how checks and maintenance should be carried out to ensure that it operates correctly. See the ”What is what?” section to locate where this equipment is positione...

Page 10 - STARTING AND STOPPING; Before starting; Stopping; Cooling

10 – English STARTING AND STOPPING Before starting Make sure that: • Power switch, cord and electrical outlet are intact. If not, they must be replaced by an authorised repairman. • Cooling air vents are not blocked. • The machine and its equipment are correctly installed. • The stand is properly fi...

Page 11 - MAINTENANCE; General

English – 11 MAINTENANCE General The lifetime of your machine can be extended considerably if it is used, cared for and maintained in the proper manner. Changing the drill bit 1 Pull out the plug. 2 Get: - The new drill bit. - Open-ended spanners, size 24 mm and 32 mm. - Water-resistant grease. 3 Re...

Page 12 - Replacing the carbon brushes

12 – English MAINTENANCE 6 If necessary contact your dealer to clean the gearbox. 7 Pour the new oil into the gearbox, about 0.5 litres. 8 Check that the sealing lip on the radial seal is intact. 9 Reassemble the machine and screw in the four screws. Be careful when assembling so as not to damage th...

Page 13 - TECHNICAL DATA

English – 13 TECHNICAL DATA DM 340 Electric motor Single-phase Rated voltage, V 230 Rated output, W 3600 Rated current, A 16 Weight, kg 14 Max. diameter drill bit, mm/inch 400/16 Water cooling Spindle thread G 1 1/4” Water connector G 1/4” Water pressure - max, bar 8 Noise emissions Sound power leve...

Page 14 - EC-declaration of conformity

14 – English TECHNICAL DATA EC-declaration of conformity (Applies to Europe only) Husqvarna AB , SE-433 81 Göteborg, Sweden, tel: +46-31-949000, declares under sole responsibility that the Husqvarna DM 340 , from 2009´s serial numbers and onwards (the year is clearly stated in plain text on the rati...

Page 15 - WIRING DIAGRAM