Heath Zenith SH-5525 - Manual
Heath Zenith SH-5525 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – INSTALLATION; Mode Switching Summary; MANUAL MODE; Eave Mount
- Page 4 – TEST AND ADJUSTMENT; Bottom of Sensor; Maximum Range; SPECIFICATIONS; Motion
- Page 5 – TROUBLESHOOTING GUIDE
- Page 6 – TECHNICAL SERvICE; No Service Parts Available for this Product
- Page 7 – Requisitos; FUNCIONAMIENTO; Prueba
- Page 8 – Resumen de las modalidades del; PRUEBA; CUIDADO: Para evitar los peligros de incen-; Montaje en pared; INSTALACION
- Page 10 – PRUEBA Y AJUSTE; Parte de abajo del detector; Lo menos sensible
- Page 12 – GARANTÍA LIMITADA A 10 AÑOS; SERvICIO TÉCNICO; de devolver el producto a la tienda.; No hay piezas de servicio disponibles para este producto.
- Page 13 – Exigences; Caractéristiques; FONCTIONNEMENT
- Page 14 – AvERTISSEMENT: Pour éviter les risques; Résumé du mode de commutation
- Page 15 – Installation De La Lampe; couper l'alimentation; Montage De La Commande; MISE EN GARDE : Coupez l’alimentation au
- Page 16 – ESSAIS ET RÉGLAGES; Bas du détecteur; Portée maximale
- Page 17 – FICHE TECHNIQUE; GUIDE DE DÉPANNAGE
- Page 18 – GARANTIE LIMITÉE DE 10 ANS; Exclusions de la garantie -; SERvICE TECHNIQUE; avant de retourner l’article au magasin.; Aucune pièce de rechange n’est disponible pour ce produit.
© 2008 HeathCo LLC
598-1161-03
1 Halogen
Lamp
Sensor
Light Control
Requirements
• The light control requires 120-volts AC.
• If you want to use Manual Mode, the control must be
wired through a switch.
• Some codes require installation by a qualified
electrician.
• This product is intended for use with the enclosed
gasket and with a junction box marked for use in wet
locations.
Model SH-5525
3 Wire
Connectors
6 Screws
(3 sizes included)
Gasket
Mounting Bolt
Mounting Strap
Light Shield
Plastic Hanger
Rubber Plug
This package includes:
OPERATION
* resets to Auto Mode at dawn.
TEST
10 5 1
TEST
ON-TIME
Put the ON-TIME switch on the
bottom of the sensor in the TEST
position.
MANUAL MODE
ON-TIME
10 5 1
TEST
... back on.
AUTO
1 Second OFF
then...
Note: When first turned on wait about 1
1
/
2
minutes for
the circuitry to calibrate.
Manual mode only works at night
because daylight returns the sensor
to AUTO.
Flip the light switch off for one second
then back on to toggle between AUTO
and MANUAL MODE.
Manual mode works only with the
ON-TIME switch in the 1, 5, or 10
position.
Put the ON-TIME switch in the 1, 5,
or 10 minute position.
Mode:
On-Time:
Works:
Day
Night
Test
5 Sec
x
x
Normal
1, 5, 10 min.
x
Manual
Until Dawn*
x
Features
• Turns on lighting when motion is detected.
• Automatically turns lighting off.
• Bulb Saver™ - Extends bulb life by up to 4x standard
bulbs. Lights bulb to full bright in under 2 seconds.
• Photocell keeps the lighting off during daylight hours.
• LED indicates motion was sensed (day or night).
Motion Sensing
Halogen Fixture
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
2 598-1161-03 CAUTION: To Avoid Fire Or Burn Hazards: • Allow fixture to cool before touching. The bulb and the fixture operate at high temperatures. • Keep fixture at least 1" (2.5 cm) from combustible ma- terials. Do not aim at objects closer than 3 ft. (1 m). • Use only T3, 250W (max.) tungst...
4 598-1161-03 TEST AND ADJUSTMENT ❒ Turn on the circuit breaker and light switch. NOTE: Sensor has about 1 1 / 2 minutes warm up period before it will detect motion. When first turned on, wait about 1 1 / 2 minutes. ❒ Turn the RANGE control to the mid position (halfway between MIN and MAX) and the O...
5 598-1161-03 TROUBLESHOOTING GUIDE SYMPTOM POSSIBLE CAUSE SOLUTION Light will not come on. 1. Light switch is turned off.2. Lamp is loose or burned out.3. Fuse is blown or circuit breaker is turned off.4. Daylight turn-off is in effect.5. Incorrect circuit wiring, if this is a new installation.6. L...
