Heath Zenith SH-5318 - Manual

Heath Zenith SH-5318 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

Page 2 – INSTALLATION; Wall Mount; Twist the junction box wires and fixture wires together
Page 3 – TEST AND ADJUSTMENT; Motion; SPECIFICATIONS; Bottom of Sensor; Least Sensitive
Page 4 – TROUBLESHOOTING GUIDE; If the problem persists, call* for assistance at; No Service Parts Available for this Product; TEN YEAR LIMITED WARRANTY
Page 5 – FUNCIONAMIENTO; Requisitos; Características; Control de luz; ual; Nota: Cuando lo prenda por primera vez espere 1; Mueva el interruptor de tiempo; Resumen de las modalidades del interruptor; Apague el interruptor por un; PRUEBA; Luz de Adorno
Page 6 – INSTALACION; Blanco a Blanco; Montaje en pared; ADvERTENCIA: Desconecte la energía en el
Page 7 – Parte de abajo del detector; Lo menos sensible
Page 8 – GUIA DE INvESTIGACION DE AvERIAS; SERvICIO TÉCNICO; producto a la tienda.; Si el problema continúa, llame al; No hay piezas de servicio disponibles para este producto.

Loading the manual

Models SH-5318

ual

rite

Motion Sensor

Light Control with

2-Level Lighting

598-1154-01

2 Shells*

Features

• Turns on lighting when motion is detected.
• Automatically turns lighting off.
• D

ual

rite

Timer.

• Photocell keeps the lighting off during daylight hours.
• LED indicates motion was sensed (day or night).

* Model SL-5318 only

This package includes:

Light Control

Sensor

Cover Plate

Lamp Holders

Plastic Hanger

Rubber Plug

Gasket

6 Screws

(3 sizes included)

Mounting Strap

Mounting Bolt

2 Wire

Connectors

Requirements

• The light control requires 120-volts AC.
• If you want to use Manual Mode, the control must be

wired through a switch.

•

S o m e c o d e s r e q u i r e i n s t a l l a t i o n b y a
qualified electrician.

• This product is intended for use with the enclosed

gasket and with a junction box marked for use in wet
locations.

TEST

TEST 1 5 20

ON-TIME

Off 3 6 Dusk to

Dawn

ual

rite

Put ON-TIME switch
on the sensor bottom
to TEST and the D

ual

rite

switch OFF.

OPERATION

* resets to Auto Mode at dawn.

ON-TIME

TEST

1 5 20

... back on.

1 Second OFF

then...

Put the ON-TIME switch in the 1, 5,
or 20 minute position.

Manual mode only works at night
because daylight returns the sensor
to AUTO.

Flip the light switch off for one second
then back on to toggle between AUTO
and MANUAL MODE.

Manual mode works only with the
ON-TIME switch in the 1, 5, or 20
position.

Note: When first turned on wait about 1

minutes for

the circuitry to calibrate.

Mode:

On-Time

Works: Day Night

Test

5 Seconds

Auto

1, 5, or 20 Min

Manual

To Dawn*

Accent

3, 6 Hr, to Dawn

AUTO

MANUAL MODE

ual

rite

Timer

Light comes on half bright for selected time after dusk
(Off, 3 hr., 6 hr., until dawn). Selecting OFF disables
this feature. The motion sensing features will continue
to work as described in this manual. If motion is sensed,
the light turns on full bright for the ON-TIME (1, 5, or
20 minutes) then returns to dim mode.

Move ON-TIME Switch to

1, 5, or 20 minutes

Mode Switching Summary

Flip light switch off

for one second then

back on*

MANUAL MODE

AUTO

TEST

* If you get confused while switching modes, turn the

power off for one minute, then back on. After the cali-
bration time the control will be in the AUTO mode.

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 2 - INSTALLATION; Wall Mount; Twist the junction box wires and fixture wires together

2 598-1154-01 INSTALLATION For easy installation, select an existing light with a wall switch for replacement. ❒ Remove the existing light fixture. ❒ Install the mounting strap as shown using two screws that fit your junction box. ❒ The plastic hanger can be used to hold the fixture while wiring. Th...

Page 3 - TEST AND ADJUSTMENT; Motion; SPECIFICATIONS; Bottom of Sensor; Least Sensitive

3 598-1154-01 TEST AND ADJUSTMENT ❒ Turn on the circuit breaker and light switch. Motion Motion The detector is most sensitive to motion across its field of view. ❒ Loosen the clamp screw in the sensor ball joint and gently rotate the sensor. ❒ Walk through the coverage area noting where you are whe...

Page 4 - TROUBLESHOOTING GUIDE; If the problem persists, call* for assistance at; No Service Parts Available for this Product; TEN YEAR LIMITED WARRANTY

4 598-1154-01 SYMPTOM Lights will not come on. L i g h t s c o m e o n in daylight. L i g h t s c o m e o n f o r n o a p p a r e n t reason. Lights turn off too l a t e i n D u s k - t o - Dawn setting POSSIBLE CAUSE 1. Light switch is turned off. 2. F l o o d l i g h t i s l o o s e o r burned out...