SIIG 04-0860A - Manuals - manualsarea.com

Page 2 - System Requirements; Windows; Package Contents; Spare low profile bracket

2 System Requirements • Desktop PC with an available 4-lane (or more) PCIe slot • Windows ® 8 (32-/64-bit) / 7 (32-/64-bit) / Vista (32-/64-bit) / XP (32-/64-bit) /Server 2003 & 2008 (32/64-bit) / Server 2008 R2 Package Contents • DP SATA 6Gb/s 4-Port Hybrid PCIe • Spare low profile bracket • SA...

Page 3 - Layout; Note; : The internal SATA 3 and SATA 4

3 eSATA 6 eSATA 5 SATA 3 (bottom)& SATA 4 (top)* SATA 1(bottom)& SATA 2(top) 2 eSATAconnectors HDD LED (optional) 4 SATAinternalconnectors Layout Figure 1: Layout * Note : The internal SATA 3 and SATA 4 connectors are dedicated channels, they can not be disabled. JP1JP2 JP4 JP3 3 2 1 3 2 1 J...

Page 4 - Jumper Settings; Figure 1

4 Jumper Settings Refer to Figure 1 for the positions of each connectors. SATA 1, 2 and eSATA 5, 6 are interchangeable. Follow the instructions in Table 1 to configure the jumper. Table 1: Jumper Settings JP1 JP5 JP1 JP5 3 2 1 3 2 1 3 2 1 3 2 1 JP1 JP5 3 2 1 3 2 1 JP1 JP5 3 2 1 3 2 1

Page 5 - Hardware Installation

5 Hardware Installation For Low profile systems, install the spare low profile bracket now.General instructions for installing the card are provided below. Since the design of computer cases and motherboards vary, refer to your c o m p u t e r ' s r e f e r e n c e m a n u a l f o r f u r t h e r in...

Page 6 - Device Connection

6 5. Carefully align the card's bus connector with the selected PCI Express slot on the motherboard. Push the board down firmly, but gently, until it is well seated. 6. Replace the slot bracket holding screw to secure the card. Device Connection The DP SATA 6Gb/s 4-Port Hybrid PCIe supports up to fo...

Page 7 - RAID Arrays; Driver; Serial ATA cable

7 4. Attach the other end of the Serial ATA data cable to the Serial ATA connector on the DP SATA 6Gb/s 4-Port Hybrid PCIe . 5. Follow the same instructions to connect the second hard drive, if needed. Device connection is now complete. RAID Arrays This controller can be configure for hardware RAID ...

Page 11 - Rebuilding a Failed Mirror Set

1 1 6. Press F10 to exit the BIOS. When asked Do you want to exit from Marvell BIOS Setup? press Y to exit and reboot. Rebuilding a Failed Mirror Set When a failure to one member occurs, you will be notified by the RAID BIOS during boot up. The steps below will guide you in rebuilding a failed mirro...

Page 12 - Deleting RAID Arrays

1 2 7. Press F10 to exit the BIOS. When asked Do you want to exit from Marvell BIOS setup? press Y to exit and reboot. Deleting RAID Arrays Deleting a RAID array will destroy data on the hard drives. Please backup all data on your hard drive before deleting any RAID array.1. As the BIOS boots press ...

Page 13 - Driver Installation

1 3 Driver Installation This section provides information on how to install the drivers. Windows 8 (32-/64-bit) / Windows 7 (32-/64-bit) / Server 2008 R2 For New Installation1. Setup the RAID array prior to Windows installation. If RAID is not required, go directly to step 2. 2. Follow Windows insta...

Page 15 - For Windows Vista

1 5 5. For 32-bit : Type D:\Drivers\storport\i386 , click Next . (Change D: to match your CD-/DVD-ROM drive letter) For 64-bit : Type D:\Drivers\storport\ amd64 , click Next . (Change D: to match your CD-/DVD-ROM drive letter) 6. Click Close , then restart the computer. Windows Vista (32-/64-bit) / ...

Page 19 - To Verify Windows Installation

1 9 6. Click Finish . 7. Repeat steps 2-6. 8. Restart the computer. To Verify Windows Installation 1. Use Device Manager to verify installation. For Windows 8 / 7 / XP / Server 2003 : Right click Computer or My Computer , click Manage , click Device Manager . For Windows Vista : Right click Computer...

Page 20 - Marvell Storage Utility

2 0 Marvell Storage Utility Follow the instuctions below to install the Marvell Storage Utility GUI. 1. Double click MSUSetup in the GUI folder on your software CD. 2. At the User Account Control, click Yes or Continue . Skip this step if not prompted. 3. At Welcome to the Marvell MSU V4 Setup Wizar...

Page 21 - Figure 4

2 1 10. Type in the Username and Password to log in. Username and Password are your Windows user name and password. If you have a user name but no password, please leave the password field blank. Figure 3 11. After log in, you can access to the MSU user interface for further VD management. See Figur...

Page 23 - Technical Support and Warranty

2 3 Technical Support and Warranty QUESTIONS? SIIG ’ s Online Support has answers! Simply visit our web site at www.siig.com and click Support . Our online support database is updated daily with new drivers and solutions. Answers to your questions could be just a few clicks away. You can also submit...