SIIG 04-0600B - Manuals - manualsarea.com

Page 2 - Package Contents; Mounting hardware; Mounting Hardware; M6x20mm Machine Screw

2 Package Contents • (2) Speaker mounts • (2) 1-hole adapters • (2) 2/4-hole adapters • (2) 2 ¼” ceiling mount extensions • Mounting hardware • Quick installation guide Mounting Hardware M6x20mm Machine Screw M5 x 20mm Machine Screw 8-32 x 5/8" Machine Screw 1/4"-20 x 1/2" Machine Screw ...

Page 3 - Installation; Single Hole Mounting; Figure 1

3 Installation Please read the instructions prior to installation. This speaker mount is designed solely for the mounting of small speakers weighing less than 8lbs. We are not responsible for damage that may occur if speakers weighing more than 8lbs. are used.The user will have to determine which ty...

Page 4 - Figure 3

4 2. Once the proper configuration is determined, secure the post to the speaker. 3. Some speakers use the smaller M4 x 8 screw, which is inserted into the off-center on the mounting post, see Figure 2 below. 4. Check the size of the hole, make sure you have the 8-32 x 5/8" machine screw, the 1/...

Page 5 - Key Hole Mounting; If your speaker has a factory key hole design, you will; Figure 4

5 5. When the correct size is determined, place the screw through the speaker post and attach to the rear of the speaker enclosure. If the screw does not tighten properly, use the M5 x 1/8" plastic washer to tighten it up. Key Hole Mounting 1. If your speaker has a factory key hole design, you w...

Page 7 - Figure 5; Locate the optimum location for the mounting plate; Figure

7 1/4"-20 x 1/2"Machine Screw 4-HoleOrientation 2-Hole Orientation Figure 5 BackSpeaker Self-Tapped Mounting 1. Locate the optimum location for the mounting plate and use it as template to mark the drilling locations. Do not drill or screw into the speaker where you could possibly damage the...

Page 8 - Figure 6; Mounting to the Wall or Ceiling; Figure 7

8 Back Speaker #12 x 3/4" SelfTapping Screw Figure 6 Mounting to the Wall or Ceiling The mounting hardware for the three different surface applications is supplied. You will need to determine what style hardware will work best with your mounting surface. Always use caution when drilling into a w...

Page 9 - Drywall Surfaces; Figure 8

9 #12 x 1 3/4" SelfTapping Screw Figure 7 3. Drill holes through the drywall and into the wood stud using a 1/8" drill bit. These holes should be drilled 1 1/2" deep, see Figure 7 above. 4. After the holes are drilled, mount the wall plate using the self tapping screws. Drywall Surfaces ...

Page 10 - Concrete Surface; Figure 9

1 0 4. With the anchors in place, mount the wall plates using the #12 x 3/4" self tapping screws, see Figure 8 below. Figure 8 #12 x 3/4" SelfTapping Screw Insert screw through wall plateand into the alligator anchor Insert AlligatorAnchor Pre Drill 5/16"Holes Concrete Surface 1. Using t...

Page 11 - With the wall anchor in place, mount the wall plate; Extension Mounting; This is for ceiling and/or shelf applications. Do not use

1 1 Figure 9 Insert AlligatorAnchor #12 x 3/4" SelfTapping Screw Using the hammer totap anchor into place Insert screw through wall plateand into the alligator anchor 3. With the wall anchor in place, mount the wall plate using the #12 x 3/4" self tapping screws, see Figure 9 above. Extensio...

Page 12 - Speaker Mounting

1 2 Low-Profile Mounting This is for wall and ceiling application.1. Install the low-profile portion of the speaker mount to the wall plate or 2 1/4" extension. 2. Secure the setscrew to hold the extension in place with the weight of the speaker attached. Tighten the allen screw usingthe provide...

Page 13 - Blank Page

Page 15 - Technical Support and Warranty

1 5 Technical Support and Warranty QUESTIONS? SIIG ’ s Online Support has answers! Simply visit our web site at www.siig.com and click Support . Our online support database is updated daily with new drivers and solutions. Answers to your questions could be just a few clicks away. You can also submit...

Page 16 - PRODUCT NAME; FCC COMPLIANCE STATEMENT:

PRODUCT NAME Satellite Speaker Mounts - 1 Pair FCC RULES: TESTED TO COMPLY WITH FCC PART 15, CLASS BOPERATING ENVIRONMENT: FOR HOME OR OFFICE USE FCC COMPLIANCE STATEMENT: This device complies with part 15 of the FCC Rules. Operation is subjectto the following two conditions: (1) This device may not...