SIIG 04-0322C - Manuals - manualsarea.com

Page 2 - Package Contents; Board Layout; Hardware Installation

2 Package Contents • Serial ATA 4-Channel PCI board • Serial ATA cable (x2) • Dual connector Serial ATA power cable • Driver CD • This quick installation guide Board Layout Serial ATA Connectors CN4 CN3 CN2 CN1 Hard Disk LED Pins Figure 1. Serial ATA 4-Channel PCI Layout Hardware Installation Genera...

Page 3 - Device Connection; Serial ATA power cable; Serial ATA cable

3 1. Turn OFF the power to your computer. 2. Unplug the power cord and remove your computer cover. 3. Remove the slot bracket from an available PCI slot. 4. Carefully align the card to the selected PCI slot push the board down firmly, but gently, until it is well seated. 5. Replace the slot bracket ...

Page 4 - Serial; Driver Installation

4 Note : If you like to monitor disk activity of the Serial ATA hard drives, you may at this time connect the hard disk LED of the system case to the Hard Disk LED Pins on the Serial ATA controller, see Figure 1 , on page 2 for the location of the pins. For most systems connect the red wire to the p...

Page 8 - To Verify Windows Vista Installation

8 Windows Vista (64-bit) For New Installation 1. Install the board and follow Microsoft procedures to install Windows accordingly. 2. At Where do yo want to install Windows? screen, click Load Drivers . 3. Insert the driver CD, click Browse . 4. Double click CD Drive... Drivers . 5. Double click 64b...

Page 10 - To Verify Windows Server 2008 Installation

10 5. Select Silicon Image SiI... SATALink Controller , then click Next . 6. Follow the on-screen instructions to complete the installation. For Existing Installation 1. Install the board and boot up Windows. 2. At the Found New Hardware Wizard , click Locate and install driver software (recommended...

Page 11 - Windows ME

11 8. Click Yes , then click Finish to complete. For Existing Installation 1. Install the board and boot up Windows. 2. At the Add New Hardware Wizard , click Next . 3. Select Search for the best driver for your device and click Next . 4. Insert the driver CD, check Specify a location , uncheck the ...

Page 12 - To Verify Windows 98SE / ME Installation

12 For Existing Installation 1. Install the board and boot up Windows. 2. At the Add New Hardware Wizard , insert the driver CD. 3. Select Specify the location of the driver (Advanced) , then click Next . 4. Check Specify a location , uncheck the other box, type D:\9x-Me , click Next . (Change D: to...

Page 13 - To Verify Windows NT4.0 Installation; This device is working properly

13 5. Select Silicon Image... Controller for Windows NT 4.0 and 2000 , and press Enter . 6. Press Enter to continue and follow on-screen i n s t r u c t i o n s t o c o m p l e t e W i n d o w s N T 4 . 0 installation. For Existing Installation 1. Install the board and boot up Windows. 2. Double cli...

Page 14 - Bios Configuration; The; BIOS; will appear everytime

14 Bios Configuration The Serial ATA 4-Channel PCI BIOS will appear everytime your system starts up. If the bios doesn't show, please try your controller in another PCI slot. During this (Post) process, the bios will show up and indicate the devices attached to it.

Page 15 - Technical Support and Warranty; Online Support

15 Technical Support and Warranty QUESTIONS? SIIG ’ s Online Support has answers! Simply visit our web site at www.siig.com and click Support . Our online support database is updated daily with new drivers and solutions. Answers to your questions could be just a few clicks away. You can also submit ...

Page 16 - features, and are backed by an extensive manufacturer warranty.

Serial ATA 4-Channel PCI is a trademark of SIIG, Inc. SIIG and the SIIG logo are registered trademarks of SIIG, Inc. Microsoft, Windows and Windows Vista are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. Pentium is a registered trade...