Page 2 - Conformity requirements; Introduction; Pre-delivery inspection and product
Contents Conformity certificates.............................................. 2Introduction............................................................... 2Safety........................................................................ 6Operation.........................................................
Page 5 - Symbols on the product
engaged. Refer to Product overview on page 3 for the position of the hour meter. Each 50 hours an oil level symbol will show for 2 hours. Refer to To do a check of the engine oil level on page 20. Symbols on the product WARNING: This product can be dangerous and cause serious injury or death to the ...
Page 6 - Product damage; Safety; Safety definitions
Cold weather start. Cutting height low. Cutting height high. Keep away from the dis- charge deck. Warning! Battery acid is corrosive, explosive and flammable. Keep body parts away from rotating parts. yyyywwxxxx The rating plate shows serial number. yyyy is the production year and ww is the producti...
Page 7 - Safety instructions regarding children; Safety instructions for operation
• Learn how to use the product and its controls safely and learn how to stop the product quickly. • Learn to recognize the safety decals.• Keep the product clean to make sure that you can clearly read signs and stickers. • Keep in mind that the operator will be held responsible for accidents that in...
Page 9 - Fuel safety
Operation conditionsThese conditions are necessary to start the engine:• The control levers are in the neutral position.• The parking brake is applied.• The drive of the blades is disengaged.The engine must stop in these situations:• The parking brake is not applied and the operator lifts from the s...
Page 10 - Safety instructions for maintenance
Transport safety • Use an approved transport vehicle for transportation of the product. • The product is heavy and can cause crush injuries. Be careful when you load it onto or off a vehicle or trailer. • A markets national or local regulations can set limit to the transportation of the product. • T...
Page 11 - Operation
• Let the product become cool before you do maintenance near the engine. • The blades are sharp and can cause cuts. Wind protection around the blades or use protective gloves when you do work on the blades. • Do not turn the engine over if the spark plug or ignition cable is removed. • Make sure tha...
Page 13 - To operate the product
2. Set the cutting deck to the transport position. Refer to To set the cutting deck in transport position or mow position on page 12. 3. Push the PTO button to disengage the drive on the cutting deck. 4. Engage the parking brake. Refer to To engage and disengage the parking brake on page 12. 5. If t...
Page 15 - Maintenance; Maintenance schedule for the operator
Maintenance Introduction WARNING: Before you do any maintenance work you must read and understand the safety chapter. Maintenance schedule * = The instructions are not given in this operator's manual. X = The instructions are given in this operator's manual.O = Refer to the engine manual for instruc...
Page 16 - To clean the product
Maintenance Daily maintenance Do maintenance at a minimum of 1 time each year Maintenance interval in hours Before After 25 50 100 300 Clean the bottom side of the cutting deck. X Clean around the engine. * Clean around the belts and the belt pulleys. * * * * Do a check of the belts and the belt pul...
Page 17 - To do a check of the parking brake; To connect the jumper cables
• Do not point the water at electrical components or bearings. Detergent usually increases the damage. • Use compressed air to clean the top side of the mower deck. • Use a water hose to clean below the cutting deck. • When the product is clean, start the cutting deck for a short period to remove re...
Page 18 - To remove the jumper cables
To remove the jumper cables Note: Remove the jumper cables in the opposite sequence to how you connect them. 1. Remove the BLACK cable from the chassis.2. Remove the BLACK cable from the fully charged battery. 3. Remove the RED cable from the 2 batteries. To remove and install the battery 1. Fold th...
Page 20 - To replace the engine oil
5. Loosen the nut on the belt guide. 6. Push in the idler arm to decrease the tension on the deck belt and carefully remove the deck belt from the pulleys. 7. Remove the deck belt from the electric clutch on the engine shaft. To install the deck belt 1. Put the deck belt around the electric clutch p...
Page 21 - Lubrication, general information
WARNING: Do not operate the engine for more than 1–2 minutes before you drain the engine oil. The engine oil becomes very hot and can cause burn injuries. Let the engine become cool before you drain the engine oil. WARNING: Use protective gloves. If you spill engine oil on your body, clean with soap...
Page 22 - Lubrication schedule
CAUTION: Do not use gasoline or other petroleum products to clean drive belts. Lubrication schedule A B C Refer to Lubrication Interval Daily Each 25 hours Each 50 hours A Lubricate the grease nipple on the pivot axle with a grease gun. X B Do a check of the oil level. X C Replace the oil filter. X ...
Page 23 - To lubricate the front wheels; Troubleshooting; Troubleshooting schedule
To lubricate the front wheels • Grease the nipple (A) with a grease gun until grease comes out from the top washer. A B • Lubricate the joint bearing of the front wheels (B) with a grease gun until grease comes out. Troubleshooting Troubleshooting schedule If you cannot find a solution to your probl...
Page 25 - Transportation, storage and disposal; Transportation; To tow the product; Storage
Problem Cause The transaxle leaks oil. The seals, housing or gaskets are damaged. There is air in the hydraulic system. The cutting result is unsatisfactory. The tire pressure is different on the right and left sides. Refer to Tire pressure on page 18. The blades are damaged. The suspension of the c...
Page 26 - Disposal
• Clean the product, refer to To clean the product on page 16. • Remove unwanted materials from the cooling fan. • Repair paint damages to prevent corrosion.• Examine the product for worn or damaged parts and tighten loose screws and nuts. • Remove the battery. Clean it, charge it, and keep it cool ...
Page 27 - Technical data
Technical data Technical data Z246 Engine Brand / Model Briggs & Stratton/44N677-0082-G1 Nominal engine output, hp / kW 10 22 / 16.5 Displacement, cm 3 724 Max. engine speed, rpm 3300 ± 100 Fuel, min. octane grade lead-free, max 10% Ethanol, max 15% MTBE 87 Tank volume, gallons / l 3.5 / 13.3 Oi...
Page 28 - Battery charging times
Z246 Blade Engagement Electromagnetic Clutch Productivity, acres/h / m 2 /h 2.4 / 9,712 Tires Tire pressure, rear – front, kPa / PSI / bar 103 / 15 / 1 Front caster tires, in. 11x 4-5 Rear tires, turf pneumatic, in. 18 x 9.5-8 Anti-scalp roller 3 adjustable Transmission Transmission Hydrostatic tran...
Page 29 - Service
Service Service Do a yearly check at an authorized service center to make sure that the product functions safely and at its best during high season. The best time to do a servicing or overhaul of the product is low season. When you send an order for the spare parts, give information about the purcha...
Page 30 - Electrical diagram
Page 31 - Requisitos de conformidad; Introducción; Inspección previa a la entrega y
Contenido Certificados de conformidad................................... 31Introducción............................................................ 31Seguridad................................................................35Funcionamiento...................................................... 41Mant...
Page 35 - Daños en el producto; Seguridad; Definiciones de seguridad
Mantenga las manos lejos de las piezas giratorias. Tenga cuidado con las personas y los animales cuando opere el producto hacia delante. Tenga cuidado con las personas y los animales cuando opere el producto hacia atrás. Arranque en clima frío. Altura de corte baja. Altura de corte alta. Manténgase ...
Page 36 - Instrucciones de seguridad para el
ADVERTENCIA: Este producto puede amputar manos y pies, y arrojar objetos. El incumplimiento de las siguientes instrucciones de seguridad puede ocasionar daños graves o la muerte. • Lea, comprenda y siga las instrucciones y advertencias de este documento, del manual de usuario y las que aparecen en e...
Page 38 - Dispositivos de seguridad en el producto
• Use siempre protectores auriculares aprobados. La exposición prolongada al ruido puede causar la pérdida permanente de la audición. • Siempre use gafas de seguridad o protección ocular cuando opere el producto o realice tareas de mantenimiento o reparación. • Use siempre zapatos o botas de protecc...
Page 40 - Seguridad de la batería
Seguridad de la batería ADVERTENCIA: Una batería dañada puede provocar una explosión y causar lesiones. Si la batería tiene una deformación o está dañada, hable con un taller de servicio Husqvarna autorizado. ADVERTENCIA: Lea atentamente las instrucciones de advertencia siguientes antes de usar el p...
Page 41 - Funcionamiento
Funcionamiento Introducción ADVERTENCIA: Antes de utilizar el producto, debe leer y entender el capítulo sobre seguridad. Para usar el producto por primera vez ADVERTENCIA: Antes de utilizar el producto por primera vez, debe leer y entender este capítulo. • Utilice una velocidad del acelerador y de ...
Page 43 - Para hacer funcionar el producto
3. Presione el botón de la PTO para desconectar la trasmisión del equipo de corte. 4. Acople el freno de estacionamiento. Consulte Para acoplar y desacoplar el freno de estacionamiento en la página 42. 5. Si la temperatura es superior a 32 °F/0 °C, siga los pasos que se indican a continuación.a) Mue...
Page 45 - Mantenimiento; Programa de mantenimiento para el
Mantenimiento Introducción ADVERTENCIA: Antes de realizar el mantenimiento, debe leer y entender el capítulo de seguridad. Programa de mantenimiento * = Las instrucciones no se proporcionan en este manual de usuario. X = Las instrucciones se proporcionan en este manual de usuario.O = Consulte el man...
Page 46 - Para limpiar el producto
Mantenimiento Para llevar a cabo un mantenimiento diario Realice el mante- nimiento por lo menos una vez al año Intervalo de mantenimiento en ho- ras Antes Después 25 50 100 300 Limpie la parte inferior del equipo de corte. X Limpie alrededor del mo- tor. * Limpie alrededor de las correas y las pole...
Page 47 - Para comprobar el freno de; Para conectar los cables de puente
Limpie el producto inmediatamente después de usarlo.• No limpie las superficies calientes, como el motor, el silenciador y el sistema de escape. Espere hasta que las superficies estén frías y luego retire el césped o la suciedad. • Antes de limpiar con agua, limpie con un cepillo. Retire el césped y...
Page 48 - Para retirar los cables de puente; Para retirar e instalar la batería
1. Conecte un extremo del cable rojo al terminal POSITIVO (+) de la batería a la batería con poca carga (A). B A C D 2. Conecte el otro extremo del cable rojo al terminal POSITIVO (+) de la batería a la batería totalmente cargada (B). ADVERTENCIA: No haga cortocircuitos en los extremos del cable roj...
Page 51 - Para cambiar el aceite del motor:
2. Tire para abrir el amortiguador del operador y acceder al motor. 3. Afloje la varilla de nivel y extráigala.4. Limpie el aceite de la varilla de nivel.5. Coloque la varilla de nivel en el orificio de la varilla de nivel y apriétela. 6. Afloje y extraiga la varilla de nivel y lea el nivel de aceit...
Page 53 - Para lubricar las ruedas delanteras; Solución de problemas; Programa de solución de problemas
Consulte Lubricación Intervalo A dia- rio Cada 25 horas Cada 50 horas A Lubrique la boquilla de engrase en el eje de pivote con una pistola de engrase. X B Compruebe el nivel de aceite. X C Reemplace el filtro de aceite. X Utilice siempre grasa de buena calidad. Utilice siempre el aceite recomendado...
Page 55 - Transporte, almacenamiento y eliminación de residuos; Transporte; Para remolcar el producto
Problema Causa La batería no se carga. La conexión de los conectores del cable con los terminales de la batería está mal. Consulte Para limpiar la batería en la página 47. El cable de carga está desconectado. El producto se mueve lentamente, con ve- locidad irregular o no se mueve. Los varillajes de...
Page 57 - Datos técnicos
Datos técnicos Datos técnicos Z246 Motor Marca / Modelo Briggs & Stratton/44N677-0082-G1 Potencia normal del motor, hp / kW 21 22 / 16,5 Cilindrada, cm 3 724 Máx. régimen del motor, rpm 3300 ± 100 Combustible, grado de octanos mínimo sin plomo, etanol al 10 % máx., 15 % MTBE máx. 87 Volumen del ...
Page 58 - Tiempos de carga de la batería
Z246 Acoplamiento de la cuchilla Embrague electromagnético Productividad, acres/h / m 2 /h 2,4 / 9712 Neumáticos Presión de los neumáticos, traseros y delanteros, kPa / PSI / bar 103 / 15 / 1 Neumáticos de la ruedecilla delantera, in 11x 4-5 Neumáticos traseros, neumático para césped, in 18 x 9,5-8 ...
Page 59 - Servicio
Servicio Servicio Realice una comprobación anual en un centro de servicios autorizado para asegurarse de que el producto funciona de forma segura y a su máximo potencial durante la temporada alta. El mejor momento para hacer mantenimiento o reparaciones a este producto es en la temporada baja. Cuand...
Page 60 - Diagrama eléctrico