Husqvarna YTH2246 - Manuals

6 CHECK TIRE PRESSURE The tires on your tractor were overinflated at the factory for shipping purposes. Correct tire pressure is important for best cutting performance.• Reduce tire pressure to PSI shown on tires. CHECK DECK LEVELNESS For best cutting results, mower housing should be properly levele...

7 These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning. CHOKE FAST SLOW REVERSE NEUTRAL HIGH LOW ENGINE OFF MOWER HEIGHT ENGINE ON ENGINE START MOWER LIFT IGNITION SWITCH CLUTCH/ BRAKE PEDAL PARKING BRAKE FREE WHEEL (Automatic Models...

8 KNOW YOUR TRACTOR READ THIS MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and ad just ments. Save this manual for future reference. (A) ATTACHMENT LIFT LEVER - Used to raise, lower, a...

9 The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye dam age. Always wear safety glass es or eye shields while operating your tractor or per form ing any adjustments or repairs. We rec om mend a wide vision safety mask over spectacles or s...

10 Fig. 9 TO ADJUST GAUGE WHEELS (See Fig. 9) Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain conditions. NOTE: Adju...

11 Fig. 11 Fig. 12 ROS "ON" POSITION ENGINE "ON" POSITION (NORMAL OPERATING) 02828 TO OPERATE ON HILLS CAUTION: Do not drive up or down hills with slopes greater than 15° and do not drive across any slope. • Choose the slowest speed before starting up or down hills. • Avoid stopping ...

12 OPERATION ADD GASOLINE • Fill fuel tank to bottom of filler neck. Do not overfill. Use fresh, clean, regular gasoline with a minimum of 87 octane. Do not mix oil with gasoline. Purchase fuel in quantities that can be used within 30 days to ensure fuel freshness. CAUTION: Wipe off any spilled oil ...

13 OPERATION PURGE TRANSMISSION CAUTION: Never engage or disengage free-wheel lever while the engine is run ning. To ensure proper operation and performance, it is rec om- mend ed that the transmission be purged before operating tractor for the first time. This procedure will remove any trapped air ...

14 MAINTENANCE ➀ General Purpose Grease ➁ Refer to Maintenance “ENGINE” Section 01965 ➁ ENGINE ➀ FRONT WHEEL BEARING ZERK ➀ STEERING SECTOR GEAR TEETH ➀ FRONT WHEEL BEARING ZERK ➀ SPINDLE ZERK ➀ SPINDLE ZERK T RAC T O R E N G I N E 3 2 2 6 1,2 2 2 1 , 2 4 5 1,2 BEFORE EACH USE EVERY 25 HOURS EVERY 8...

15 MAINTENANCE Fig. 14 Fig. 15 TRACTOR Always observe safety rules when per form ing any main te nance. BRAKE OPERATION If tractor requires more than five (5) feet (1,5 m) to stop at highest speed in high est gear on a level, dry concrete or paved surface, then brake must be checked and ad just ed. ...

16 TRANSAXLE MAINTENANCE The transmission fan and cooling fins should be kept clean to assure proper cooling.Do not attempt to clean fan or transmission while engine is running or while the transmission is hot. To prevent pos - si ble damage to seals, do not use high pressure water or steam to clean...

17 MAINTENANCE AIR FILTER Your engine will not run properly using a dirty air filter. Service air cleaner more often under dusty conditions. ENGINE COOLING SYSTEM To ensure proper cooling, make sure the grass screen, cooling fins, and other external surfaces of the engine are kept clean at all times...

19 WARNING: TO AVOID SE RI OUS IN JU RY, BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS: • Depress brake pedal fully and set parking brake. • Place motion control lever in neutral position. • Place attachment clutch in “DISENGAGED” position. • Turn ignition key to “STOP” and remove key. • Make sure th...

21 SERVICE AND ADJUSTMENTS FRONT-TO-BACK ADJUSTMENT (See Figs. 30 & 31) IMPORTANT: Deck must be level side-to-side. To obtain the best cutting re sults, the mower blades should be adjusted so the front tip is 1/8" to 1/2" (3,1 to 12,7 mm) lower than the rear tip when the mower is in its ...

22 Fig. 33 Fig. 32 SERVICE AND ADJUSTMENTS TO REPLACE MOTION DRIVE BELT (See Fig. 33) Park the tractor on level surface. En gage parking brake. For as sis tance, there is a belt installation guide decal on bottom side of left footrest.BELT REMOVAL -• Remove mower (See “TO REMOVE MOWER” section in th...

23 TO REMOVE WHEEL (See Fig. 35) • Block up axle securely.• Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose). • Repair tire and reassemble.• On rear wheels only: align grooves in rear wheel hub and axle. Insert square key. • Replac...

24 TO REPLACE HEADLIGHT BULB • Raise hood. • Pull bulb holder out of the hole in the backside of the grill. • Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill. • Close hood. INTERLOCKS AND RELAYS Loose or damaged wiring may cause your tractor to ru...

25 STORAGE ENGINE FUEL SYSTEM IMPORTANT : IT IS IMPORTANT TO PREVENT GUM DEPOSITS FROM FORMING IN ES SEN TIAL FUEL SYSTEM PARTS SUCH AS CARBURETOR, FUEL FIL TER, FUEL HOSE, OR TANK DURING STORAGE. ALSO, EXPERIENCE INDICATES THAT ALCOHOL BLENDED FUELS (CALLED GASOHOL OR USING ETHANOL OR METHANOL) CAN...

26 TROUBLESHOOTING PROBLEM CAUSE CORRECTION Will not start 1. Out of fuel. 1. Fill fuel tank. 2. Engine not “CHOKED” properly. 2. See “TO START ENGINE” in Operation section. 3. Engine flooded. 3. Wait several minutes before attempting to start. 4. Bad spark plug. 4. Replace spark plug. 5. Dirty air ...

28 15 DEGREES MAX. FOLD ALONG DOTTED LINE THIS IS A 15 DEGREE SLOPE ONLY RIDE UP AND DOWN HILL, NOT ACROSS HILL SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION WARNING: To avoid serious injury, operate your tractor up and down the face of slopes, never across the face. Do not mow slopes great...

29 I. NIÑOS ADVERTENCIA: LOS NIÑOS PUEDEN SUFRIR DAÑOS CON EL USO DE ESTE EQUIPO. La Aca- demia Estadounidense de Pediatría (American Academy of Pediatrics) recomienda que sólo se permita a niños con una edad mínima de 12 años manejar máquinas cortacésped manuales, y al menos de 16 años para manejar...

30 REGLAS DE SEGURIDAD Prácticas de Operación Seguras para las Segadoras Conducibles IV. REMOLQUE • Remolcar sólo con una máquina que tenga un gancho dis- eñado para remolcar. Enganchar el equipo o remolcar sólo en el punto dispuesto al efecto. • Seguir las recomendaciones del productor con respecto...

31 FELICITACIONES por la compra de su tractor. Ha sido diseñado, planificado y fabricado para darle la mejor confiabilidad y el mejor rendimiento posible.En el caso de que se encuentre con cualquier problema que no pueda solucionar fácilmente, haga el favor de ponerse en con- tacto con un centro de ...

32 PEDAZOS PARA LA MONTAJE Su tractor nuevo ha sido montado en la fábrica con la excepción de aquellas partes que no se han montado por razones de envío. HERRAMIENTAS NECESARIAS PARA EL MONTAJE Un juego de llaves de tubo facilitará el montaje. A continuación se enumeran los tamaños de las llaves est...

33 MONTAJE REVISIÓN DE LA PRESIÓN DE LAS LLANTAS Las llantas en su unidad fueron infladas demasiado en la fá- brica por razones de envío. La presión de las llantas correctas es importante para obtener el mejor rendimiento en el corte.• Reduzca la presión de los neumáticos a la PSI que se indica en e...

34 Estos símbolos pueden aparecer sobre su tractor o en la literatura proporcionada con el producto. Aprenda y comprenda sus significados. ESTRANGU- LACIÓN RÁPIDO LENTO MARCHA ATRÁS NEUTRO ALTO BAJO MARCHA ATRÁS MARCHA HACIA ADELANTE COMBUS- TIBLE MOTOR APAGADO ALTURA DE LA SEGADORA MOTOR ENCENDIDO ...

35 Nuestros tractores cumplen con los estándares de seguridad del American National Standard Institute. OPERACIÓN Fig. 3 FAMILIARICESE CON SU TRACTOR LEA ESTE MANUAL DE OPERARIO Y LAS REGLAS DE SEGURIDAD ANTES DE OPERAR SU TRACTOR Compare las ilustraciones con su tractor para familiarizarse con las ...

36 La operación de cualquier tractor puede hacer que salten objetos extraños dentro de sus ojos, lo que puede producir daños graves en éstos. Siempre use anteojos de seguridad o pro tec cio- nes para los ojos mientras opere su tractor o cuando haga ajustes o reparaciones. Recomenda- mos gafas de seg...

37 Fig. 7 PARA MOVERSE HACIA ADELANTE Y HACIA ATRÁS (Vea Fig. 7) La dirección y la velocidad del movimiento son controladas por medio de la palanca de control de movimiento (J).• Haga arrancar el motor con la palanca de con trol de mo vi- mien to en la posición de neutro. • Suelte el freno de estaci...

38 OPERACIÓN Fig. 12 FUNCIONAMIENTO ATRÁS (Vea Fig. 12) Tu tractor está equipado con el Sistema de Funcionamiento Atrás (ROS). Cualquier tentativa del operador de viajar marcha atrás con el embrague puesto apagará el motor a menos que la llave de ignición se ponga en la posición de “ON” del ROS. 028...

39 OPERACIÓN ANTES DE HACER ARRANCAR EL MO TOR REVISE EL NIVEL DE ACEITE DEL MOTOR El motor de su tractor se envía de fábrica ya lleno con aceite de peso para verano. • Revise el aceite del motor con el tractor en terreno nivelado. • Remueva la tapa/varilla indicadora de nivel de relleno del aceite ...

40 OPERACIÓN PURGAR LA TRANSMISIÓN PRECAUCIÓN: Nunca enganche o desen- ganche la palanca del control de rue da libre cuando el motor esta fun cio nan do. Para asegurar la operación y ejecución adecuada, es re co men- da do que la transmisión sea purgada antes de operar el tractor para la primera vez...

41 MANTENIMENTO ➀ Grasa de proposito general ➁ Refiérase a la sección del “MOTOR” en Mantenimiento 01965 ➁ MOTOR ➀ ACCESORIO DE GRASA DEL RODAMIENTO DE LA RUEDA DELANTERA ➀ PLANCHA DEL ENGRANAJE DE SECTOR DE DIRECCIÓN ➀ ACCESORIO DE GRASA DEL RODAMIENTO DE LA RUEDA DELANTERA ➀ ACCESORIO DE GRASA DEL...

43 ENFRIAMIENTO DEL TRANSEJE Las aletas de enfriamiento y el ventilador de la transmisión tienen que mantenerse limpios para asegurar el enfriamiento adecuado.No trate de limpiar el ventilador o la transmisión cuando el motor esté funcionando o mientras la transmisión esté caliente.• Inspeccione el ...

44 MANTENIMENTO Fig. 19 SILENCIADOR Inspeccione y cambie el silenciador corroído y el amortiguador de chispas (si viene equipado) pues pueden crear un peligro de incendio y/o daños. FILTRO DE COMBUSTIBLE (Vea Fig. 19) El filtro de combustible debe cambiarse una vez cada tempo- rada. Si el filtro de ...

45 MANTENIMENTO PUERTO DE LAVADO ADAPTADOR DE BOQUILLA MANGUERA Fig. 21 IMPORTANTE : Tire de la manguera para asegurarse de que la conexión está bien fija.5. Abra la llave del agua.6. Desde la posición del operador del tractor, vuelva a arrancar el motor y ponga la palanca de aceleración en la posic...

46 E F C G Q R D G P B M A SERVICIO Y AJUSTES ADVERTENCIA: PARA EVITAR LESIÓNES SERIAS, ANTES DE DAR CUALQUIER SERVICIO O DE HACER AJUSTES: • Presione el pedal del embrague/freno completamente y aplique el freno de estacionamiento. • Ponga la palanca de control de movimiento en la posición de neutro...

49 Fig. 33 PARA REEMPLAZAR LA CORREA DE TRANS- MISIÓN (Vea Fig. 33) Estacione el tractor en una superficie nivelada. Ponga el freno de mano. Si necesita asistencia, del lado de abajo del apoyapiés hay una guía práctica para el montaje de la correa.DESMONTAJE DE LA CORREA• Desmonte la cortadora (Ver ...

50 SERVICIO Y AJUSTES Fig. 35 LLAVE CUADRADA (RUEDA TRASERA SOLAMENTE) ARANDELAS ANILLO DE RETENCIÓN CUBIERTA DEL EJE PARA HACER ARRANCAR EL MOTOR CON UNA BATERÍA BAJA (Vea Fig. 36) ADVERTENCIA: Las baterías de ácido- plo mo generan gases explosivos. Man- t e n g a l a s c h i s p a s , l a s l l a ...

51 PARA REMOVER EL CONJUNTO DEL CAPÓ Y dEL ENREJADO (Vea Fig. 38) • Levante el capó.• Desabroche el conector del alambre de las luces delanteras.• Párese delante del tractor. Agarre el capó en los lados, in- clínelo un poco hacia el motor y sáquelo del tractor. • Para volver a instalar el capó, aseg...

52 ALMACENAMIENTO Inmediatamente prepare su tractor para el almacenamiento al final de la temporada o si el tractor no se va a usar por 30 días o más. Advertencia: Nunca almacene el tractor con gasolina en el estanque dentro de un edificio en donde los gases pueden al can zar una llama expuesta o un...

53 IDENTIFICACIÓN DE PROBLEMAS PROBLEMA CAUSA CORRECCIÓN No arranca 1. Sin combustible. 1. Llene el estanque de combustible. 2. Motor sin la “ESTRANGULACIÓN” (CHOKE) adecuada. 2. Vea “PARA HACER ARRANCAR EL MOTOR” en la sec- ción de operación. 3. Motor ahogado. 3. Espere varios minutos antes detrata...

55 15 GRADOS MAX. PLEGAR A LO LARGO DE LA LÍNEA PUNTEADA ESTA ES UNA PENDIENTE DE 15 GRADOS SOLAMENTE ANDE CUESTA ARRIBA O CUESTA ABAJO Y NO ATRAVIESE EL CERRO GUÍA SUGERIDA PARA MEDIR LAS PENDIENTES CON LA VISTA PARA UNA OPERACIÓN SEGURA ADVERTENCIA: Para evitar daños graves, haga funcionar su trac...

5 UNASSEMBLED PARTS (2) Keys Slope Sheet Key (1) Oil Drain Tube ASSEMBLY When right or left hand is mentioned in this man ual, it means when you are in the operating po si tion (seated be hind the steer ing wheel). TO REMOVE TRACTOR FROM CAR TON UNPACK CARTON • Remove all accessible loose parts and ...

6 ASSEMBLY CHECK TIRE PRESSURE The tires on your tractor were overinflated at the factory for shipping purposes. Correct tire pressure is important for best cutting performance.• Reduce tire pressure to PSI shown on tires. CHECK DECK LEVELNESS For best cutting results, mower housing should be proper...

7 OPERATION These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their mean- ing. DANGER, KEEP HANDS AND FEET AWAY FREE WHEEL (Automatic Models only) KEEP AREA CLEAR SLOPE HAZARDS 15 15 (SEE SAFETY RULES SECTION) BATTERY REVERSE FORWARD FAST SLOW ...

8 OPERATION KNOW YOUR TRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and ad just ments. Save this manual for future reference. Our tractors conform to the appli...

9 OPERATION The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye dam age. Always wear safety glass es or eye shields while operating your tractor or per form ing any ad just ments or repairs. We rec om mend standard safety glasses or a wide ...

10 OPERATION TO ADJUST MOWER CUT TING HEIGHT (See Fig. 8) The po si tion of the at tach ment lift le ver (A) de ter mines the cut ting height. • Put attachment lift lever in desired cutting height slot.The cutting height range is ap prox i mate ly 1" to 4". The heights are measured from the ...

11 OPERATION FIG. 11 TOWING CARTS AND OTHER AT TACH MENTS Tow only the attachments that are recommended by and comply with specifications of the manufacturer of your trac- tor. Use common sense when towing. Too heavy of a load, while on a slope, is dangerous. Tires can lose traction with the ground ...

12 CAUTION: Alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to sep a ra tion and for ma tion of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied ...

13 FIG. 12 MOWING TIPS • Mower should be properly leveled for best mowing per- formance. See “TO LEVEL MOWER HOUSING” in the Service and Adjustments section of this manual. • The left hand side of mower should be used for trim- ming. • Drive so that clippings are discharged onto the area that has be...

14 MAINTENANCE T RAC T 0 R Inspect Muffler/Spark Arrester Clean Air Filter Change Engine Oil (with oil filter) Replace Air Filter Paper Cartridge Replace Spark Plug Check Engine Oil Level Clean Engine Cooling Fins Clean Air Screen 1 - Change more often when operating under a heavy load or in high am...

15 MAINTENANCE FIG. 13 02 544 MANDREL ASSEMBLY BLADE BLADE BOLT (SPECIAL) CENTER HOLE STAR BATTERY Your tractor has a battery charging system which is suf fi cient for normal use. However, periodic charging of the battery with an automotive charger will extend its life.• Keep battery and terminals c...

16 MAINTENANCE V-BELTS Check V-belts for deterioration and wear after 100 hours of operation and replace if necessary. The belts are not ad just able. Re place belts if they begin to slip from wear. TRANSAXLE COOLING The transmission fan and cooling fins should be kept clean to assure proper cooling...

17 MAINTENANCE MUFFLER Inspect and replace corroded muffler and spark arrester (if equipped) as it could create a fire hazard and/or dam- age. SPARK PLUGS Replace spark plugs at the beginning of each mowing season or after every 100 hours of operation, whichever occurs first. Spark plug type and gap...

18 SERVICE AND ADJUSTMENTS WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SER VICE OR AD JUST - MENTS: • Depress brake pedal fully and set parking brake. • Place attachment clutch in “DISENGAGED” position. • Turn ignition key to “STOP” and remove key. • Make sure the blades and all moving p...

20 SERVICE AND ADJUSTMENTS • If adjustment is necessary, see step in Visual Adjust- ment instructions above. • Recheck measurements, adjust if necessary until both sides are equal. FRONT-TO-BACK ADJUSTMENT (See Figs. 24 and 25) IMPORTANT: Deck must be level side-to-side. To obtain the best cutting r...

21 SERVICE AND ADJUSTMENTS TO REPLACE MOTION DRIVE BELT (See Fig. 27) Park the tractor on level surface. En gage parking brake. For as sis tance, there is a belt installation guide decal on bottom side of left footrest.BELT REMOVAL - • Remove mower (See “TO RE MOVE MOWER” in this section of manual)....

22 SERVICE AND ADJUSTMENTS FIG. 28 RE TAIN ING RING WASH ERS SQUARE KEY (REAR WHEEL ONLY) AXLE COVER TO START ENGINE WITH A WEAK BATTERY (See Fig. 29) WARNING : Lead-acid batteries gen- er ate ex plo sive gases. Keep sparks, flame and smoking ma te ri als away from bat ter ies. Always wear eye pro t...

24 STORAGE Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more. WARNING: Never store the trac tor with gas o line in the tank inside a building where fumes may reach an open flame or spark. Allow the engine to cool before stori...

25 TROUBLESHOOTING POINTS Will not start 1. Out of fuel. 1. Fill fuel tank. 2. Engine not “CHOKED” properly. 2. See “TO START ENGINE” in Operation section. 3. Engine flooded. 3. Wait several minutes before attempting to start. 4. Bad spark plug. 4. Replace spark plug. 5. Weak or dead battery. 5. Rec...

27 TRACTOR - - MODEL NUMBER YTH2246 (96043003700), PRODUCT NO. 960 43 00-37 SCHEMATIC M FUSE STARTER SOLENOID BATTERY ELECTRIC CLUTCH CLUTCH/BRAKE (PEDAL UP) REVERSE SWITCH (NOT IN REVERSE) SEAT SWITCH (NOT OCCUPIED) SHORTING CONNECTOR CHASSIS HARNESS IGNITION UNIT HOUR METER CHASSIS HARNESS CONNECT...

28 TRACTOR - - MODEL NUMBER YTH2246 (96043003700), PRODUCT NO. 960 43 00-37 ELECTRICAL 30 33 42 40 26 28 71 400449 29 34 43 25 27 41 22 21 16 55 46 46 102

29 TRACTOR - - MODEL NUMBER YTH2246 (96043003700), PRODUCT NO. 960 43 00-37 ELECTRICAL KEY PART NO. NO. DESCRIPTION 1 532 14 49-27 Battery 2 874 76 04-12 Bolt Hex Head 1/4-20 x 3/4 8 532 19 32-28 Box Battery 16 532 17 61-38 Switch Interlock Push-In 21 532 18 37-59 Harness Socket Light W/4152J 22 532...

30 TRACTOR - - MODEL NUMBER YTH2246 (96043003700), PRODUCT NO. 960 43 00-37 CHASSIS CHASSISTEX?GTHUSQ 189 189 152 162 196 222 138

32 TRACTOR - - MODEL NUMBER YTH2246 (96043003700), PRODUCT NO. 960 43 00-37 DRIVE ª DRIVETEX?(USQª4UFF4ORQ

36 TRACTOR - - MODEL NUMBER YTH2246 (96043003700), PRODUCT NO. 960 43 00-37 SEAT ASSEMBLY 1 532 19 75-18 Seat 2 532 18 01-66 Bracket Pivot Fender 3 532 14 06-75 Strap, Asm Fender 6 873 80 06-00 Nut, Lock W/Ins. 3/8-16 unc 7 532 12 41-81 Spring, Seat Cprsn 8 532 17 18-77 Bolt 5/16-18 uncx 3/4 w/Sems ...

37 TRACTOR - - MODEL NUMBER YTH2246 (96043003700), PRODUCT NO. 960 43 00-37 DECALS NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm KEY PART NO. NO. DESCRIPTION 6 2 1 3 11 4 10 5 9 8 7 wheel_art_1-tex WHEELS AND TIRES KEY PART NO. NO. DESCRIPTION KEY PART NO. NO. DESCRIPTION 4 1 ...

38 TRACTOR - - MODEL NUMBER YTH2246 (96043003700), PRODUCT NO. 960 43 00-37 MOWER DECK 30 67 151 194 152 186 86 187 193 5 37 152 42 43 60 38 63 46 147 55 64 30 32 31 33 34 56 57 59 188 1 69 69 199 40 46 145 15 14 21 25 26 27 198 29 21 21 23 24 144 36 57 70 149 19 6 6 117 116 119 117 119 116 195 122 ...

39 TRACTOR - - MODEL NUMBER YTH2246 (96043003700), PRODUCT NO. 960 43 00-37 MOWER DECK KEY PART NO. NO. DESCRIPTION NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm 1 532 41 08-63 Mower Housing 2 532 40 55-06 Cover Mandrel RH 3 532 40 55-07 Cover Mandrel LH 5 532 12 46-70 Retaine...

40 TRACTOR - - MODEL NUMBER YTH2246 (96043003700), PRODUCT NO. 960 43 00-37 MOWER LIFT 7 3 87 10 88 2 89 90 87 98 97 97 lift-tex_5 91 89 87 100 2 532 19 52-23 Shaft Asm., Lift 3 532 19 52-31 Lever Asm., Lift Rh 7 532 19 64-92 Grip, Lever 10 532 19 63-14 Spring Torsion 87 532 19 42-09 Pin Cotter 7/16...

43 15 DEGREES MAX. FOLD ALONG DOTTED LINE THIS IS A 15 DEGREE SLOPE ONLY RIDE UP AND DOWN HILL, NOT ACROSS HILL SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION WARNING: To avoid serious injury, operate your tractor up and down the face of slopes, never across the face. Do not mow slopes great...