Husqvarna T540 XP Mark III - Manuals

it releases the throttle trigger (B). If you release the handle, the throttle trigger and the throttle trigger lockout move back to their initial positions. This function locks the throttle trigger at idle speed. B A Chain catcherThe chain catcher catches the saw chain if it breaks or derails. Corre...

• Always move the product at least 3 m (10 ft) away from the refuelling area and fuel source before starting. Min. 3m(10 ft) After refuelling, there are some situations where you must never start the product:• If you have spilled fuel or chain oil on the product. Wipe off the spillage and allow rema...

9. Make sure that the saw chain tension is correct. 9 2 7 5 1 3 8 4 6 Connectivity This product is prepared for connectivity and has a location for installation of a Husqvarna Connectivity Device. When the Husqvarna connectivity device is installed, the product has wireless technology and can use Hu...

• Information about, and help with, product parts and servicing. To start to use Husqvarna Connect 1. Download the Husqvarna Connect app on your mobile device. 2. Register in the Husqvarna Connect app.3. Follow the instruction steps in the Husqvarna Connect app to connect and register the product. N...

2. Clean the area around the fuel tank cap. 3. Shake the container and make sure that the fuel is fully mixed. 4. Remove the fuel tank cap slowly to release the pressure. 5. Fill the fuel tank. CAUTION: Make sure that there is not too much fuel in the fuel tank. The fuel expands when it becomes hot....

WARNING: No saw chain fully prevents kickback. Always obey the instructions. Common questions about kickback • Will the hand always engage the chain brake during a kickback?No. It is necessary to use some force to push the front hand guard forward. If you do not use the force necessary, the chain br...

• Use full throttle when you cut and decrease to idle speed after each cut. CAUTION: Engine damage can occur if the engine runs for too long at full throttle without load. • When you cut, put the spiked bumper into the trunk and use it as a lever. Note: Not all models have a spiked bumper. Speak to ...

WARNING: Make sure that the product is safely attached when you lift it to the operator in the tree. Tree operator As a tree operator, follow the instructions below.1. Before you disconnect the safety strop from the ascent tools, you must attach the product to the harness. Attach the product to the ...

• If you must climb with the product, attach the product to the rear connection point on the harness. The rear connection point keeps the product clear from climbing lines and makes sure that the weight has central support down your spine. WARNING: You must engage the chain brake before you let the ...

Daily maintenance Weekly maintenance Monthly maintenance Turn the guide bar, do a check of the lubrication hole and clean the groove in the guide bar. Refer to To do a check of the guide bar on page 27. Clean the carburetor area. Do a check of all cables and connec- tions. Make sure that the guide b...

Refer to Product overview on page 3 for information about where the vibration damping system is on your product. To do a check of the start/stop switch 1. Start the engine.2. Push the start/stop switch to the STOP position. The engine must stop. To do a check of the muffler WARNING: A used muffler/s...

4. Let the pulley rotate slowly rearward to release the recoil spring. 5. Remove the bolt in the center of the pulley and remove the pulley. 6. Hold the starter rope handle.7. Pull the starter rope until 1 cm of the spring guide is shown. At the same time, press down the starter handle cover and rem...

To sharpen the saw chain Information about the guide bar and saw chain WARNING: Use protective gloves when you use or do maintenance on the saw chain. A saw chain that does not move can also cause injuries. Replace a worn or damaged guide bar or saw chain with the guide bar and saw chain combination...

Troubleshooting The engine does not start Product part to examine Possible cause Action Starter pawls The starter pawls are blocked. Adjust or replace the starter pawls. Clean around the pawls. Speak to an approved service work- shop. Fuel tank Incorrect fuel type. Drain the fuel tank and fill with ...

Transportation, storage and disposal Transportation and storage • For storage and transportation of the product and fuel, make sure that there are no leaks or fumes. Sparks or open flames, for example from electrical devices or boilers, can start a fire. • Always use approved containers for storage ...

Husqvarna T540XP ® Mark III Weight, kg 3.8 Noise emissions 2 Sound power level, measured dB(A) 110 Sound power level, guaranteed L WA dB(A) 112 Sound levels 3 Equivalent sound pressure level at the operator’s ear, dB(A) 102 Equivalent vibration levels, a hveq 4 Front handle, m/s 2 3.5 Rear handle, m...

Declaration of Conformity EU Declaration of conformity We, Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declare on our sole responsibility that the product: Description Chainsaw for tree service Brand Husqvarna Type / Model T540XP ® Mark III Identification Serial numbers dating fro...