Husqvarna PA 1100 - Manuals

Page 2 - KEY TO SYMBOLS; Symbols; Saw attachment with shaft PA 1100

2 – English KEY TO SYMBOLS . Symbols WARNING! The machine can be a dangerous tool if used incorrectly or carelessly, which can cause serious or fatal injury to the operator or others. Please read the operator’s manual carefully and make sure you understand the instructions before using the machine. ...

Page 3 - CONTENTS; Contents

English – 3 CONTENTS Contents Note the following before starting: Husqvarna AB has a policy of continuous product development and therefore reserves the right to modify the design and appearance of products without prior notice. Long-term exposure to noise can result in permanent hearing impairment....

Page 4 - SAFETY INSTRUCTIONS; Cutting equipment; Specification of bar and saw chain; Bar

4 – English SAFETY INSTRUCTIONS Cutting equipment This section describes how you can achieve maximum clearing capacity and extend the life of the cutting attachment through correct maintenance and using the right type of cutting attachment. Only use cutting equipment recommended by us! See the Techn...

Page 5 - Chain

English – 5 SAFETY INSTRUCTIONS Chain • Saw chain pitch (inches). (The distance between three drive links, divided by two.) • Drive link width (mm/inches) • Number of drive links. Sharpening your chain and adjusting raker clearance General information on sharpening cutting teeth • Never use a blunt ...

Page 6 - General advice on setting raker clearance; Tensioning the chain

6 – English SAFETY INSTRUCTIONS • Always file cutting teeth from the inside face outwards. Reduce the pressure on the return stroke. File all the teeth on one side of the bar first. Then turn the saw over and file the remaining teeth from the other side. • File all the teeth to the same length. When...

Page 7 - Lubricating cutting equipment; Chain oil; Filling with chain oil; Adjusting chain lubrication

English – 7 SAFETY INSTRUCTIONS 1 Undo the bar nut. 2 Raise the tip of the bar and stretch the chain by tightening the chain tensioning screw using the combination spanner. Tighten the chain until it does not sag from the underside of the bar. 3 Use the combination spanner to tighten the blade nut w...

Page 8 - Chain drive sprocket

8 – English SAFETY INSTRUCTIONS 2 Check that the oil channel in the gear housing is clean. Clean if necessary. 3 Check that the bar tip sprocket turns freely. If the chain lubrication system is still not working after carrying out the above checks you should contact your service workshop. Checking w...

Page 9 - Personal protection

English – 9 SAFETY INSTRUCTIONS Personal protection • Always wear boots and other equipment described under the heading Personal protective equipment in the machine’s Operator’s Manual. • Always wear working clothes and heavy-duty long trousers. • Never wear loose clothing or jewellery. • Make sure ...

Page 12 - What is what on the saw attachment? (Saw attachment without shaft PA)

12 – English WHAT IS WHAT? What is what on the saw attachment? (Saw attachment without shaft PA) 10 8 1 2 7 5 4 3 9 6 12 11 13 14 10 1 Bevel gear 2 Chain lubrication adjustment screw 3 Harness support hook 4 Protective guard for saw chain 5 Bar nut 6 Chain tensioning screw 7 Chain 8 Bar 9 Chain oil ...

Page 13 - Fitting the cutting head; Fitting the bar and chain; Fitting the hanging ring

English – 13 ASSEMBLY Fitting the cutting head (Saw attachment with shaft PA 1100) • Fit the cutting head on the shaft so that the screw (A) is aligned with the hole in the shaft as shown. • Tighten screw A. • Tighten screw B. CAUTION! Make sure that the drive shaft inside the shaft engages with the...

Page 14 - Adjusting the harness; Filling with oil; Check before starting

14 – English ASSEMBLY Adjusting the harness You should always use the harness with the machine to give maximum control over the machine and reduce the risk of fatigue in your arms and back. • Put on the harness. • Hook the machine onto the harness support hook. • Adjust the length of the harness so ...

Page 15 - TECHNICAL DATA; Technical data

English – 15 TECHNICAL DATA Technical data Note 1: Equivalent sound pressure level is calculated as the time-weighted energy total for sound pressure levels under various working conditions with the following time distribution: 1/2 idling and 1/2 max speed. Bar and chain combinations The following c...

Page 16 - EC-declaration of conformity

16 – English TECHNICAL DATA EC-declaration of conformity (Applies to Europe only) We, Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel +46-36-146500, declare that this saw attachment from 2002’s serial numbers and onwards (the year is clearly stated in plain text on the type plate, with subsequent ser...