Husqvarna M-ZT 52 - Manuals

Good Service Husqvarna's products are sold only in specialized retail stores with complete service. This ensures that you as a customer receive only the best support and service. Before the product is delivered, the machine has, for example, been inspected and adjusted by your retailer. See the cert...

These symbols are found on the machine and in the operator manual.Study them carefully so that you know what they mean. IMPORTANT INFORMATION Xxxx xxxxxx xxxxx xxxx xxxxxxxxx xxxxxx xxxxxxxxx. xx xxxxxxxx xxxx xxxxxx. WARNING! Xxxx xxxxxx xxxxx xxxx xxxxxxxxx xxxxxx xxxxxxxxx. xx xxxxxxxx xxxx xxxxx...

General Operation • Read, understand, and follow all instructions on the machine and in the manual before starting. • It is recommended that someone be aware that you are mowing and can provide help in case of injury or accident. • Anyone who operates, maintains, and/or services this machine must fi...

WARNING! Do not drive up or down hills with slopes greater than 10 degrees. And do not drive across any slopes. • Choose a low ground speed so that you will not have to stop while on the slope. • Do not mow on wet grass. Tires may lose traction.• Avoid starting, stopping, or turning on a slope. If t...

• Remove gas-powered equipment from the truck or trailer and refuel it on the ground. If this is not possible, refuel such equipment with a portable container, rather than from a gasoline dispenser nozzle. • Keep the nozzle in contact with the rim of the fuel tank or container opening at all times u...

Transport IMPORTANT INFORMATION The park brake is not sufficient to lock the machine in place during transport. Ensure that the machine is well fastened to the transport vehicle. Always reverse the machine onto the transport vehicle to avoid tipping it over. WARNING! Use extreme caution when loading...

This operator manual describes the Husqvarna Zero Turn Rider. The rider is fitted with a Briggs & Stratton four-stroke overhead valve engine.Transmission from the engine is made via a belt-driven hydraulic pumps. Using the left and right steering controls, the flow is regulated and thereby the d...

Fuses Fuses are located on the left hand side of the machine and are accessed by tilting the seat forward. Fuses are flat pin fuses type as used in automobiles. The 20 A is the primary fuse. The 7.5 A is for the mower deck coupling. Fuel Shut Off Valve The fuel shut off valve is located at the left ...

Fuel Tank IMPORTANT INFORMATION Experience indicates that alcohol blended fuels (called gasohol, ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, t...

Read the Safety section and following pages, if you are unfamiliar with the machine. Training Due to unique steering capabilities, zero turn mowers are far more maneuverable than typical riding mowers.This section should be reviewed in its entirety prior to attempting to move the mower under its own...

Starting the Engine 1. Sit on the seat.2. Raise the mower deck to the transport position by locking the lift pedal fully forward. 3. Activate the park brake pulling the lever upwards. WARNING! Engine exhaust and certain vehicle components contain or emit chemicals considered to cause cancer, birth d...

Running 1. Release the park brake by moving the lever downward. NOTE: The mower is equipped with an operator presence system. When the engine is running, any attempt by the operator to leave the seat without first setting the park brake will shut off the engine. 2. Move the steering controls inwards...

IMPORTANT INFORMATION Leaving the ignition switch in any other position than OFF will cause the battery to be discharged. 5. When the machine is standing still, activate the park brake by pulling the lever upward. If the engine has been worked hard, allow it to idle a minute to attain a normal opera...

Mowing Tips • Observe and flag rocks and other fixed objects to avoid collisions. • Begin with a high cutting height and reduce it until the desired mowing result is attained. The average lawn should be cut to 2½" (64 mm) during the cool season and over 3" (76 mm) during the hot months. For ...

Maintenance Schedule The following is a list of maintenance procedures that must be performed on the machine. For those points not described in this manual, visit an authorized service workshop. An annual service carried out by an authorized service workshop is 1) First change after 8-10 hours. When...

Battery Your mower is equipped with a maintenance free battery and does not need servicing. However, periodic charging of the battery with an automotive type battery charger will extend its life. • Keep battery and terminals clean.• Keep battery bolts tight.• See chart for charging times. IMPORTANT ...

Safety System The machine is equipped with a safety system that prevents starting or driving under the following conditions.The engine can only be started when: • The mower deck is disengaged.• The steering controls are in the outer, locked neutral position. • The park brake is on. IMPORTANT INFORMA...

Anti-scalp Rollers Anti-scalp rollers are properly adjusted when they are just slightly off of the ground when the deck is at the desired cutting height in the operating position. Anti-scalp rollers then keep the deck in the proper position to help prevent scalping in most terrain conditions.Anti-sc...

Pump Belt The belts are not adjustable. Replace belts if they begin to slip from wear. Replacing Pump Belt Park the mower on a level surface. Engage the park brake. Belt Removal From the top side of the deck:1. Remove the deck belt (see Deck Belt Removal in this section of the manual). 2. Tilt seat ...

Adjusting the Mower Deck Check the tire pressure before adjustment of the mower deck. See Tire Pressures in Maintenance section. Faulty mower deck adjustments will cause an uneven mowing result. Leveling deck Adjust the deck while the mower is on a level surface. Make sure the tires are inflated to ...

General Remove the ignition key to prevent unintentional movements during lubrication.When lubricating with an oil can, it must be filled with engine oil.When lubricating with grease, unless otherwise stated, use a high grade molybdenum disulphide grease.For daily use, the machine should be lubricat...

WARNING! To prevent burns, the engine should be shut off and allowed to cool slightly so the engine is still warm but the surrounding surfaces and oil are not. Engine oil change NOTE: Change the engine oil when the engine is warm. Refer to the engine owner’s manual for the correct replacement oil an...

Transmission Purging Due to the effects air has on efficiency in hydrostatic drive applications, it is critical to purge the system.These purge procedures should be implemented any time a hydrostatic system has been opened for maintenance or if any additional oil has been added to the system.Resulti...

Problem / Cause Engine will not start Blade switch is engagedSteering controls are not locked in the neutral positionPark brake is not activatedBattery is deadContamination in the carburetor or fuel lineFuel supply shutoff valve is closedClogged fuel filter or fuel lineIgnition system faulty Starter...

Winter Storage The machine should be readied for storage at the end of the mowing season or if it will not be in use for more than 30 days. Fuel allowed to stand for long periods of time (30 days or more) can leave sticky residues that can plug the carburetor and disrupt engine function.Fuel stabili...

Engine Frame Manufacturer Briggs & Stratton Cutting Width 52" (133 cm) Type Endurance Commercial Cutting Height 1½"-4½" (3.8-11.4 cm) Power 26 HP 1) Uncut Circle 0 Lubrication Pressure with oil filter Number of Blades 3 Fuel Min 87 octane unleaded (Max ethanol 10%, Max MTBE 15%) Blad...

Accessories Collection system Engine crankshaft bolt 50 ft/lb (67 Nm) Deck pulley bolts 75 ft/lb (100 Nm) Lug nuts 75 ft/lb (100 Nm) Blade bolt 55 ft/lb (75 Nm) Standard ¼" fasteners 9 ft/lb (12 Nm) Standard 5 / 16 " fasteners 18 ft/lb (25 Nm) Standard 3 / 8 " fasteners 33 ft/lb (44 Nm) ...

Delivery Service Charge the battery r Adjust the tire pressure of all wheels to 15 PSI (1 bar) r Mount the steering controls in the normal position r Connect the contact box to the cable for the seat’s safety switch r Check that the right amount of oil is in the engine r Adjust the position of the s...

At Least Once Each Year Clean the engine’s cooling air intake q Replace the air cleaner’s foam prefilter q Replace the air filter’s paper cartridge q Change the engine oil q Replace the engine oil filter q Check/adjust the cutting height q Check/adjust the park brake q Clean/Change the spark plugs q...