Husqvarna K3000 Wet - Manuals

English – 5 WHAT IS WHAT? What is what on the power cutter - K3000 Wet? 1 Rear handle 2 Guard for the blade 3 Water kit 4 Cutting blade 5 Locking the axle 6 Front handle 7 Inspection covers 8 Power switch lock 9 Switch 10 Water tap 11 Water connection with flow limiter 12 Type plate 13 Brush retaine...

6 – English SAFETY INSTRUCTIONS Steps before using a new power cutter • Please read the operator’s manual carefully and make sure you understand the instructions before using the machine. • The machine is only designed for cutting hard materials, such as concrete, brick, masonry as well as cast iron...

English – 7 SAFETY INSTRUCTIONS General safety warnings Save all warnings and instructions for future reference. The term ”power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool. Work area safety • Keep work area clean and well lit. Cl...

8 – English SAFETY INSTRUCTIONS Personal safety • Stay alert, watch what you are doing and use common sense when operaing a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result i...

English – 9 SAFETY INSTRUCTIONS Machine ′′′′ s safety equipment This section describes the machine ′ s safety equipment, its purpose, and how checks and maintenance should be carried out to ensure that it operates correctly. See the ”What is what?” section to locate where this equipment is positione...

10 – English SAFETY INSTRUCTIONS Ground fault circuit interrupter (K3000 Wet) Ground fault circuit interrupters are for protection in case an electrical fault should occur. The LED indicates that the ground fault circuit interrupter is on and that the machine can be switched on. If the LED is not on...

English – 11 SAFETY INSTRUCTIONS Blade vibration The blade can become out-of-round and vibrate if an excessive feed pressure is used. A lower feed pressure can stop the vibration. Otherwise replace the blade. The blade must be of the recommended type for the material to be cut. Abrasive discs The cu...

12 – English SAFETY INSTRUCTIONS Dry cutting with diamond blade Wet cutting with diamond blade (K3000 Wet) Water cooling, which is used when cutting concrete, cools the blade and increases its service life while also reducing the formation of dust. Water connection with flow limiter (K3000 Wet) Ther...

English – 13 SAFETY INSTRUCTIONS • The guard for the cutting equipment should be adjusted so that the rear section is flush with the work piece. Spatter and sparks from the material being cut are then collected up by the guard and led away from the user. • Feed down the machine in line with the blad...

14 – English ASSEMBLY Assembly Fitting the cutting blade Husqvarna’s blades are approved for hand-held power cutters. Blades are manufactured with three different diameters of centre holes: 20 mm (0.787"), 22.2 mm (7/8") and 25.4 mm (1"). Bushings can be fitted on the machine axle to adj...

English – 15 STARTING AND STOPPING Starting and stopping Before starting (K3000 Wet) Water connector Connect the water hose to the water supply (A). The water flow is regulated using the water tap (B). Ground fault circuit interrupter Make sure the ground fault circuit interrupter is switched on. Th...

16 – English MAINTENANCE Maintenance Cooling system The machine is equipped with an efficient fan to cool the motor. Cooling air which is drawn in through the grille by the machines rear handle passes over the stator and rotor and out through the front of the motor housing. In order for the machine ...

English – 17 MAINTENANCE Changing the grease The following parts must be dismantled to change the grease in the gear housing: 1 Flange washers holding the cutting blade 2 The sealing ring 3 Support flange for the guard 4 Guard for the blade 5 The four screws holding the shield. Lift the shield toget...

18 – English TECHNICAL DATA ´®z+S3•¶52¨ ´®z+S3•¶52¨ Cutting equipment Max. blade speed, rpm 4500 Technical data K3000 K3000 Wet Engine Protection class I I Ground fault circuit interrupter No Yes Rated voltage, V Europe 230 230 Great Britain 110 110 USA / Canada / Japan 100-120 100-120 Australia 230...