Husqvarna Automower 535 AWD EPOS - Manuals

2 Introduction Serial number: Product number: PIN code: The serial number and the product number are on the product rating plate and on the product carton.• Register your product on www.husqvarna.com. Enter the serial number of the product, the product number and the date of purchase to register you...

2.3 Product overview 3 5 7 11 10 4 9 2 1 6 18 16 17 22 21 26 19 20 36 37 34 33 38 35 32 30 28 31 29 24 27 8 23 25 13 14 15 12 1. Front body 2. Ultrasonic sensors 3. Front top cover 4. Handle 5. Rear top cover 6. EPOS ™ module 7. Charging plates 8. Rear body 9. Headlights 10. Front wheels 11. Rear wh...

21. Blades22. Blade disc23. Contact plates24. LED indicator of the charging station25. Charging station26. Power supply 1 27. Low-voltage cable28. Loop wire for boundary wire and guide wire 2 29. Connector for the loop wire 3 30. Stakes 4 31. Couplers for loop wire 5 32. Screws to attach the chargin...

3 Installation with EPOS ™ technology 3.1 Introduction - Installation WARNING: Read and understand the safety chapter before you install the product. CAUTION: Use original spare parts and installation material. Note: Refer to www.husqvarna.com for more information about installation. 3.2 System over...

• Install the virtual boundaries in slopes that are maximum 50%. 3.8.4 To examine where to make stay-out zones • Make stay-out zones around objects that are larger than 2x2 m / 6.6x6.6 ft. • Make sure that the stay-out zone includes the complete area were the product must not operate (B). B A Note: ...

4 Installation with boundary wire 4.1 Introduction - Installation WARNING: Read and understand the safety chapter before you install the product. CAUTION: Use original spare parts and installation material. Note: Refer to www.husqvarna.com for more information about installation. 4.2 Primary compone...

• Put the boundary wire 35 cm / 14 in. (B) from an obstacle that is more than 5 cm / 2 in. high. 35 cm /14 " > 5 cm / 2 " • Put the boundary wire 30 cm / 12 in. (C) from an obstacle that is 1-5 cm / 0.4-2 in. high. 1-5 cm / 0.4 - 2 " 30 cm / 12 " • Put the boundary wire 10 cm / 4 ...

To make an island, isolate areas in the work area with the boundary wire. We recommend to isolate all stable objects in the work area.Some obstacles are resistant to a collision, for example, trees or bushes that are more than 15 cm / 6 in. in height. The product will collide with the obstacle and t...

• If the work area has a slope, put the guide wire in a straight line from the bottom of the slope to the top of the slope. If it is not possible to make a straight line, put the guide wire diagonally across the slope. CAUTION: Do not put the guide wire in parallel with the slope, as the illustratio...

5 Settings The product has factory settings but the settings can be adapted to each work area. 5.1 Schedule In the Schedule menu you can change the schedule settings for the product. You can set separate schedule settings for each work area. Secondary areas cannot be scheduled. The schedule function...

function to lower the cutting height from the maximum cutting height to the specified cutting height gradually during 10 days. If you change the cutting height manually during this time it will disable the TargetHeight function. 5.3 Pattern The settings for pattern can be set for each work area with...

6 Operation 6.1 To set the product to ON WARNING: Read and understand the safety chapter before you use the product. 1. Push the ON/OFF button for 3 seconds. Note: Make sure that the STOP button is pushed down. 2. Use the Automower ® Connect app to enter the PIN code. The correct PIN code must be en...

7 Maintenance 7.1 Introduction - maintenance WARNING: Set the product to OFF before you do maintenance on the product. WARNING: Use protective gloves. For better operation and lifetime of the product, make sure to clean the product regularly and replace worn parts.When the product is new, examine th...

To prepare Weekly Every year Every third year Examine the rubber grommets on the chassis to make sure that it is sealed correctly. O Examine the skid plate and skid plate bearing. O Examine the rubber bellows in the cutting height adjustment system. O Examine the rubber bellows for the collision col...

4. Make sure that the blade disc can rotate freely. 5. Make sure that the blades are not damaged and can pivot freely. 7.3.2 To clean the chassis • Clean the bottom of the chassis with a brush or a moist cloth. 7.3.3 To clean the wheels The product does not operate satisfactorily in slopes if the wh...

8 Troubleshooting 8.1 Introduction - troubleshooting In this chapter, a number of messages are listed which may be shown in Automower ® Connect and Husqvarna Fleet Services ™ if there is a malfunction. There is a proposal action to the cause and steps to take for each message. This chapter also pres...

8.3 LED indicator of the charging station The LED indicator of the charging station is green when the installation is correct. If the LED indicator of the charging station is not green, follow the troubleshooting table below. Speak to your local Husqvarna representative or go to www.husqvarna.com fo...

8.5 Find breaks in the loop wire Breaks in the loop wire are usually the result of unintentional physical damage to the wire such as when gardening with a shovel. In countries with ground frost, also sharp stones that move in the ground can damage the wire. Breaks can also occur due to the wire bein...

9 Transportation, storage and disposal 9.1 Transportation The supplied Li-ion batteries obey the Dangerous Goods Legislation requirements.• Obey all applicable national regulations. • Obey the special requirement on package and labels for commercial transportations, including by third parties and fo...

10 Technical data 10.1 Technical data Dimensions Automower ® 535 AWD EPOS Length, cm / in. 93 / 36.6 Width, cm / in. 55 / 21.6 Height, cm / in. 33 / 13.1 Weight, kg / lbs 17.6 / 39 Electrical system Automower ® 535 AWD EPOS Battery, Lithium-Ion 18.0 V/8.0 Ah Art. No. 534 19 93-01 Battery, Lithium-Io...

Frequency Band Support Bluetooth ® Frequency range 2400.0-2483.5 MHz Automower ® Connect 2G GSM 850 MHz, E-GSM 900 MHz, DCS 1800 MHz, PCS 1900 MHz Automower ® Connect 4G Band 12 (700 MHz), Band 28 (700 MHz), Band 13 (700 MHz), Band 20 (800 MHz), Band 26 (850 MHz), Band 5 (850 MHz), Band 19 (850 MHz)...

11 Declaration of Conformity 11.1 Original EU Declaration of Conformity 62 - Declaration of Conformity 1427 - 012 - 16.10.2024

11.2 Translated EU Declaration of Conformity We, Husqvarna AB, SE 561 82 Huskvarna, SWEDEN, Tel. +46 36 146500 declare on our sole responsibility that the product: Description Robotic lawn mower Brand Husqvarna Type/Model HUSQVARNA AUTOMOWER ® 535 AWD EPOS Identification Serial numbers dating from 2...

12 Applicable to UK market 12.1 Original UK Declaration of Conformity 64 - Applicable to UK market 1427 - 012 - 16.10.2024

12.2 Statement of compliance This product complies with the UK Product Security and Telecommunications Infrastructure Regulation. Statement of compliance for your product can be found at www.husqvarna.com/uk/support/. 1427 - 012 - 16.10.2024 Applicable to UK market - 65

For more information, read the Operator's manual for the reference station and the Operator's manual for the robotic lawn mower. A System overview The EPOS system contains a robotic lawn mower, a charging station and a reference station. The robotic lawn mower and the reference station receive satel...