Husqvarna Automower 435X AWD NERA - Manuals

2 Introduction Factory PIN code: 1234 Serial number: Product number: The serial number and the product number are on the product rating plate and on the product carton.• Register your product on www.husqvarna.com. Enter the serial number of the product, the product number and the date of purchase to...

2.3 Product overview 3 5 7 15 13 16 11 10 4 9 17 2 14 1 6 20 18 19 24 23 25 27 28 21 22 38 39 36 35 40 37 34 32 30 33 31 26 29 12 8 1. Front body 2. Ultrasonic sensors 3. Front top cover 4. Handle 5. Rear body 6. EPOS ™ module 7. Charging plates 8. Rear top cover 9. Headlights 10. Front wheels 11. R...

21. Rating plate (incl. product identification code)22. Front chassis with electronics and motors23. Blades24. Blade disc25. Contact plates26. LED indicator of the charging station27. Charging station28. Power supply 1 29. Low-voltage cable30. Loop wire for boundary wire and guide wire 2 31. Coupler...

2.8 Menu structure overview in Automower ® Access 2.8.1 Symbols in the main menu for Automower ® Access Cutting heightIn the Cutting height menu you can adjust the cutting height. ParkIn the Park menu you can set the product to park until further notice or to the set schedule. MowIn the Mow menu you...

3 Installation with EPOS ™ technology 3.1 Introduction - Installation WARNING: Read and understand the safety chapter before you install the product. CAUTION: Use original spare parts and installation material. Note: Refer to www.husqvarna.com for more information about installation. For installatio...

• Make sure that the areas between objects have a distance (F) of minimum 4 m / 13.1 ft. F Note: For areas with a width less than 4 m / 13.1 ft. a transport path can be made for the robotic lawn mower to go through without cutting. 3.8.2 To install the map objects in a slope The product can operate ...

4 Installation with boundary wire 4.1 Introduction - Installation WARNING: Read and understand the safety chapter before you install the product. CAUTION: Use original spare parts and installation material. Note: Refer to www.husqvarna.com for more information about installation. 4.2 Primary compone...

35 cm /14 " > 5 cm / 2 " • Put the boundary wire 30 cm / 12 in. (C) from an obstacle that is 1-5 cm / 0.4-2 in. high. 1-5 cm / 0.4 - 2 " 30 cm / 12 " • Put the boundary wire 10 cm / 4 in. (D) from an obstacle that is less than 1 cm / 0.4 in. high. 10 cm / 4 " max 1 cm / 0.4 &#...

To make an island, isolate areas in the work area with the boundary wire. We recommend to isolate all stable objects in the work area.Some obstacles are resistant to a collision, for example, trees or bushes that are more than 15 cm / 6 in. in height. The product will collide with the obstacle and t...

• If the work area has a slope, put the guide wire in a straight line from the bottom of the slope to the top of the slope. If it is not possible to make a straight line, put the guide wire diagonally across the slope. CAUTION: Do not put the guide wire in parallel with the slope, as the illustratio...

5 Settings The product has factory settings but the settings can be adapted to each work area. 5.1 Schedule In Schedule you can change the schedule settings for the product.The Schedular Tool adapts the schedule to the size of your work area. The Schedule function controls which hours the product op...

5.4.1 Object avoidance The Object avoidance function makes the product decrease speed when it comes near an obstacle to avoid to collide with it. Note: This can cause that the grass is not cut around the obstacle. This function can cause the product to not cut high grass satisfactorily. 5.4.2 Weathe...

5.7.2 Reset to factory settings The user settings can be reset to factory settings. Note: PIN code, Loop signal, Messages and Date & Time will not be reset. 5.8 Security The security settings controls the PIN code, the GeoFence and other security functions. The correct PIN- code must be entered ...

6 Operation 6.1 To set the product to ON WARNING: Read and understand the safety chapter before you use the product. 1. Push the jog wheel for 3 seconds. 3 sec Note: Make sure that the STOP button is pushed down. If the STOP button is not pushed down a STOP symbol shows on the display. 2. Use the jo...

7 Maintenance 7.1 Introduction - maintenance WARNING: Set the product to OFF before you do maintenance on the product. WARNING: Use protective gloves. For better operation and lifetime of the product, make sure to clean the product regularly and replace worn parts.When the product is new, examine th...

To prepare Weekly Every year Every third year Examine the rubber grommets on the chassis to make sure that it is sealed correctly. O Examine the skid plate and skid plate bearing. O Examine the rubber bellows in the cutting height adjustment system. O Examine the rubber bellows for the collision col...

4. Make sure that the blade disc can rotate freely. 5. Make sure that the blades are not damaged and can pivot freely. 7.3.2 To clean the chassis • Clean the bottom of the chassis with a brush or a moist cloth. 7.3.3 To clean the wheels The product does not operate satisfactorily in slopes if the wh...

8 Troubleshooting 8.1 Introduction - troubleshooting In this chapter, a number of messages are listed which may be shown in Automower ® Connect and Automower ® Access if there is a malfunction. There is a proposal action to the cause and steps to take for each message. This chapter also presents som...

Message Cause Action Reference station communication prob- lem The product is not connected to the refer- ence station. Do a pairing operation between the product and the reference station. The reference station is not installed correct- ly. Examine the installation of the reference sta- tion. The p...

8.6 Find breaks in the loop wire Breaks in the loop wire are usually the result of unintentional physical damage to the wire such as when gardening with a shovel. In countries with ground frost, also sharp stones that move in the ground can damage the wire. Breaks can also occur due to the wire bein...

9 Transportation, storage and disposal 9.1 Transportation The supplied Li-ion batteries obey the Dangerous Goods Legislation requirements.• Obey all applicable national regulations. • Obey the special requirement on package and labels for commercial transportations, including by third parties and fo...

10 Technical data 10.1 Technical data Dimensions Automower ® 435X AWD NERA Length, cm / in. 93 / 36.6 Width, cm / in. 55 / 21.7 Height, cm / in. 33 / 13.1 Weight, kg / lbs 18.1 / 39.9 Electrical system Automower ® 435X AWD NERA Battery, Lithium-Ion 18.0 V/8.0 Ah Art. No. 534 19 93-01 Battery, Lithiu...

Power Class Bluetooth ® Output power 8 dBM Automower ® Connect 2G Power Class 4 (GSM/E-GSM) 33 dBm Power Class 1 (DCS/PCS) 30 dBm Power Class E2 (GSM/E-GSM) 27 dBm Power Class E2 (DCS/PCS) 26 dBm Automower ® Connect 3G Power Class 3 24 dBm Automower ® Connect 4G Power Class 3 23 dBm SRD868 (Europe) ...

11 Declaration of Conformity 11.1 Original EU Declaration of Conformity 62 - Declaration of Conformity 1404 - 017 -

11.2 Translated EU Declaration of Conformity We, Husqvarna AB, SE 561 82 Huskvarna, SWEDEN, Tel. +46 36 146500 declare on our sole responsibility that the product: Description Robotic lawn mower Brand Husqvarna Type/Model HUSQVARNA AUTOMOWER ® 435X AWD NERA Identification Serial numbers dating from ...

12 Applicable to UK market 12.1 Original UK Declaration of Conformity 64 - Applicable to UK market 1404 - 017 -

12.2 Statement of compliance This product complies with the UK Product Security and Telecommunications Infrastructure Regulation. Statement of compliance for your product can be found at www.husqvarna.com/uk/support/. 1404 - 017 - Applicable to UK market - 65

GUIDA RAPIDA COME INSTALLARE IL ROBOT TAGLIAERBA CON EPOS™ Robot tagliaerba Stazione di riferimento EPOS™ (opzionale) Stazione di ricarica 2 Posizionare la stazione di ricarica 7 Impostare un programma nell'app e iniziare a tagliare il prato 3 Caricare e avviare il tagliaerba 5 Attivare EPOS™ nell'a...

7 Scaricare l'app Automower® Connect ed eseguire l'abbinamento COME INSTALLARE IL ROBOT TAGLIAERBA CON CAVO Robot tagliaerba Stazione di ricarica Kit di installazione 2 Posizionare la stazione di ricarica 3 Caricare e avviare il tagliaerba 4 Posare il cavo perimetrale 8 Impostare un programma nell'a...

QUICK GUIDE HOW TO INSTALL YOUR ROBOTIC LAWN MOWER WITH EPOS™ Robotic lawn mower EPOS™ reference station (optional) Charging station 2 Place the charging station 7 Set a schedule in the app and start mowing 3 Charge and startthe mower 5 Activate EPOS™ in the Automower Connect® app 4 Download the Aut...

7 Download theAutomower® Connect app and pair HOW TO INSTALL YOUR ROBOTIC LAWN MOWER WITH WIRE Robotic lawn mower Charging station Installation kit 2 Place the chargingstation 3 Charge and startthe mower 4 Lay boundary wire 8 Set a schedule in the app and start mowing 5 Connect the guide wireto the ...