Husqvarna Automower 410XE NERA - Manuals

2 Introduction 2.1 Introduction Factory PIN code: 1234 Serial number: Product number: The serial number and the product number are on the product rating plate and on the product carton.• Register your product on www.husqvarna.com. Enter the serial number of the product, the product number and the da...

15. Chassis with electronics, battery and motors16. EdgeCut blade disc17. Main blade disc18. Handle19. Contact plates20. LED indicator of the charging station21. Hatch22. Charging station23. Low-voltage cable24. Power supply 4 25. Extra blades26. Screws to attach the charging station27. Measurement ...

3 Installation with wire 3.1 Introduction - Installation Read this chapter to install the product with a boundary wire. A boundary wire is not necessary if you install the product with the EPOS ™ . Read the operator's manual for the reference station EPOS ™ RS1 to install it with the product. WARNIN...

Some obstacles are resistant to a collision, for example, trees or bushes that are more than 15 cm / 5.9 in. in height. The product will collide with the obstacle and then select a new direction.• Put the boundary wire to and around the obstacle to make an island. • Put the 2 sections of boundary wi...

B D C A 3.5 Installation of the product 3.5.1 Installation tools • Hammer/plastic mallet: To simplify putting the stakes into the ground. • Edge cutter/straight spade: To bury the boundary wire. • Combination pliers: For cutting the boundary wire and pressing the connectors together. • Adjustable pl...

4 Settings This chapter gives information about the settings for the product that you can make in the Automower ® Connect app. All setting for the product are available in Automower ® Connect. Some settings can also be made in Automower ® Access, refer to Automower ® Access on page 9. The product ha...

5 Operation The most frequently used operation settings are included in the Automower ® Access, refer to Automower ® Access on page 6. All operating modes are available in the Automower ® Connect app. 5.1 To set the product to ON WARNING: Read and understand the safety chapter before you use the pro...

3. Push the jog wheel for 3 seconds to set the product to OFF. You can also use the jog wheel to select Power off in the menu in the display. 4. Make sure that the LED indicator on the jog wheel is not lit. 5.6 To charge the battery When the product is new or after long-term storage, the battery can...

6 Maintenance 6.1 Introduction - maintenance WARNING: Set the product to OFF before you do maintenance on the product. WARNING: Use protective gloves. For better operation and lifetime of the product, make sure to clean the product regularly and replace worn parts.When the product is new, examine th...

To prepare Weekly Every year Every third year Examine the skid plate and skid plate bearing. O Examine the rubber bellows in the cutting height adjustment system. O Examine the rubber bellows for the collision columns. O Replace the rubber bellows for the collision columns. O Examine and clean the a...

6.5 Replacement of the blades WARNING: Husqvarna can only guarantee safety if you use Husqvarna original blades with the embossed crowned H-mark logotype. WARNING: You must replace the screws when you replace the blades. The used screws can wear quickly and make the blade come loose, this can cause ...

7 Troubleshooting 7.1 Messages The messages in the table below are shown in Automower ® Connect and Automower ® Access. Speak to your Husqvarna representative if the same message shows frequently. Message Cause Action Wrong PIN code An incorrect PIN code has been entered. 5 tries are permitted, and ...

Symptoms Cause Action The product is parked for hours in the charging station. The product has operated the maximum cut- ting time for the day. No action. Refer to Schedule on page 20. The hatch is closed but the START button is not pushed. Push the STOP button to open the hatch. Enter the PIN code ...

8 Transportation, storage and disposal 8.1 Transportation The supplied Li-ion batteries obey the Dangerous Goods Legislation requirements.• Obey all applicable national regulations. • Obey the special requirement on package and labels for commercial transportations, including by third parties and fo...

9 Technical data 9.1 Technical data Dimensions Automower ® 310E NERA Automower ® 410XE NERA Length, cm/in. 68/26.8 68/26.8 Width, cm/in. 44/17.2 44/17.2 Height, cm/in. 28/11.0 28/11.0 Weight, kg/lb 12.2 / 27 12.1 / 27 Electrical system Automower ® 310E NERA Automower ® 410XE NERA Battery, Lithium-Io...

GUIDA RAPIDA COME INSTALLARE IL ROBOT TAGLIAERBA CON EPOS™ Robot tagliaerba Stazione di riferimento EPOS™ (opzionale) EPOS™ plug-in Stazione di ricarica 2 Montare e posizionare la stazione di ricarica 5 Collegare EPOS™ Plug-in 8 Impostare un programma nell'app e iniziare a tagliare il prato 3 Carica...

7 Scaricare l'app Automower® Connect ed eseguire l'abbinamento COME INSTALLARE IL ROBOT TAGLIAERBA CON CAVO Robot tagliaerba Stazione di ricarica Kit di installazione 2 Montare e posizionare la stazione di ricarica 3 Caricare e avviare il tagliaerba 4 Posare il cavo perimetrale 8 Impostare un progra...

QUICK GUIDE HOW TO INSTALL YOUR ROBOTIC LAWN MOWER WITH EPOS™ Robotic lawn mower EPOS™ reference station (optional) EPOS™ plug-in Charging station 2 Assemble and place the charging station 5 Attach EPOS™ Plug-in 8 Set a schedule in the app and start mowing 3 Charge and startthe mower 6 Activate EPOS...

7 Download theAutomower® Connect app and pair HOW TO INSTALL YOUR ROBOTIC LAWN MOWER WITH WIRE Robotic lawn mower Charging station Installation kit 2 Assemble and place thecharging station 3 Charge and startthe mower 4 Lay boundary wire 8 Set a schedule in the app and start mowing 5 Connect the guid...