Husqvarna 968999110 / W4815A - Manuals

Husqvarna 968999110 / W4815A – Manual in PDF format online.

Manuals:

Manual

Manual Husqvarna 968999110 / W4815A

Summary

Page 2 - MODELS; Adjustment Instructions for:; Gear Drive Intermediate Walk Behind

2 MODELS / I.D. : 968999101 / W3212A 968999107 / W3213A 968999102 / W3612A 968999108 / W3613A 968999103 / W3614A 968999104 / W4814A 968999110 / W4815A Adjustment Instructions for: Gear Drive Intermediate Walk Behind

Page 8 - ETS Gear Drive Intermediate Walk Behind

8 Models: 968999117 / W3613ETS 968999120 / W4815ETS ETS Gear Drive Intermediate Walk Behind

Page 11 - Figure 1; CASTER HEIGHT ADJUSTMENT

11 AXLE ADJUSTMENTBOLTS POSITION A POSITION B POSITIONC POSITIOND PLACE JACKHERE Figure 1 REAR AXLE HEIGHT ADJUSTMENT LOOSEN BOLTS EACHSIDE CASTER SWIVEL 1/2" SPACERS MACHINERY BUSHING CASTER HEIGHT ADJUSTMENT Figure 2 Setup & Adjustments

Page 12 - CUTTING HEIGHT ADJUSTMENT CHART

12 CUTTING HEIGHT ADJUSTMENT CHART AXLE POSITION NUMBER OF SPACERS BELOW CASTER ARM NUMBER OF 1/4" BLADE SPACERS UNDER CUTTER HOUSING CUTTING HEIGHT (IN INCHES) 1 1/21 3/4 22 1/42 1/21 3/4 22 1/42 1/22 3/42 1/22 3/4 33 1/43 1/2 33 1/43 1/23 3/4 43 1/43 1/23 3/4 44 1/43 1/23 3/4 44 1/44 1/23 3/4 ...

Page 13 - Figure 3

13 BRAKE / TRACTION ADJUSMENT 1. Disconnect the brake linkage from the brakeband arm. 2.With the mower in gear, place the drive leversin the drive position. Firmly pull back on thehandles until the tires slide to seat the drivebelts into the pulleys. 3. Measure the distance between the back drivelev...

Page 15 - NOTE

15 Figure 6 AUXILARY BELT ADJUSTMENT ROD IDLER PIVOT POINT TURNBUCKLE ENGAGEMENT IDLER ASSEMBLY 1/4" BEFORE OPERATINGBe thoroughly familiar with all controls and howto use them before operating the mower. Knowbeforehand how to stop the engine, drivewheels, and mower blades in preparation forposs...

Page 16 - CUTTING HEIGHT; Hydro Intermediate Walk Behind

16 Adjustment Instructions for: MODELS / I.D. : 968999105 / WH3614A 968999111 / WH3615A 968999106 / WH4817A CUTTING HEIGHT 1. Before changing cutting heights make sure the blades are off, key switch is off, and removespark plug wire or wires.2. Cutting height ranges from 1 1/2” to 5” in 1/4” increme...

Page 18 - MOTION CONTROL ADJUSTMENT

18 CUTTING HEIGHT ADJUSTMENT CHART Note: To quickly achieve small changes in cuttingheights, move the spacers from under the cutter housingto above the cutter pulley. (Each spacer moved will givean additional 1/4" of cutting height ). USE ONLY 4 BLADE SPACERS MAXIMUM AXLE POSITION NUMBER OF SPAC...

Page 19 - REVERSE SPRING DETENT ADJUSTMENT

19 Figure 4 (Right side cut away view of console.) Figure 3 REVERSE SPRING DETENT ADJUSTMENT 1. To check if your reverse spring detent adjustment is set right. Make sure your ground speedlever is pulled back to the neutral position. Release the thumb latches (both sides) and pull up onthe control le...

Page 20 - BLADE DRIVE BELT ADJUSTMENT

20 Figure 5 AUXILARY BELT ADJUSTMENTROD IDLER PIVOT POINT TURNBUCKLE ENGAGEMENT IDLERASSEMBLY 1/4" BLADE DRIVE BELT ADJUSTMENT 1. Before performing adjustments on blade belt, turn the mower off and disconnect spark plug wireor wires.2. Remove front deck belt shield.3. Loosen nut on turnbuckle.4....

Page 21 - ENGINE BELT GUIDES; PUMP BELT

21 ENGINE BELT GUIDES 1. Before performing adjustments on belt guides, turn the mower off and disconnect spark plug wireor wires.2. Belt guides under the engine should be adjusted as shown in figure 6. Figure 6 PUMP BELT 1. Before performing adjustments on pump belt, turn the mower off and disconnec...

Page 22 - ETS Hydro Intermediate Walk Behind

22 Models: 968999127 / WHF4215ETS968999129 / WHF4818ETS968999130 / WHF5218ETS ETS Hydro Intermediate Walk Behind

Page 24 - FIGURE 3

24 ADJUSTMENTS FRONT DECK BELT ROUTING: PUMP BELT 1. Before performing adjustments on pump belt, turn the mower off and disconnect spark plug wire orwires.2. Check tension on the belt. If it feels loose adjustment will need to be made.3. Loosen the nut on the bottom of the idler pulley.4. Slide the ...

Page 25 - Mid Mount Zero Turn Riders 42” & 48”; Setup Instructions for:; ADJUSTMENTS

25 Mid Mount Zero Turn Riders 42” & 48” 968999157 / ZTHKH4818A968999158 / ZTHKH4820A 968999167 / ZTHKW4218A968999168 / ZTHKW4818A968999169 / ZTHKW4821A MODEL / I.D. : Setup Instructions for: ADJUSTMENTS PARK BRAKE:1. Stop engine and remove key. While the park brake lever”A” is in the on position...

Page 26 - FIGURE 2

26 FIGURE 2 CUTTING HEIGHT:1. Stop the mower and disengage the blades.2. Raise the deck height lever to the transport position.3. Remove the height adjustment pin and place it in the desired cutting height hole. Move deckheight lever down onto the pin and mow. NOTE: anti-scalp rollers must be in the...

Page 31 - Adjustments

31 Adjustments Cutting HeightStop the mower and disengage the blades. Raise the deck height lever to the transportposition. Remove the height adjustment pin andplace it in the desired cutting height hole.Lower the lift lever down onto pin. NOTE:Anti-scalp rollers must be in the properposition for ma...