Husqvarna 966957301 - Manuals

Page 2 - IMPORTANT MESSAGE TO THE CONSUMER AND/OR OPERATOR

2 SAFETY RULES AND PRECAUTIONS As with any item of power equipment it is necessary that you learn and observe ALL safety precautions. This includes the care for the machine as well as personal safety. This machine is only as dangerous as the person who is operating it. DO NOT BE CARELESS! In the beg...

Page 4 - TABLE OF CONTENTS; DESCRIPTION PAGE; PLEASE READ CAREFULLY!

4 TABLE OF CONTENTS DESCRIPTION PAGE Safety Rules and Precautions.......................................................................................................2-3Assembly............................................................................................................................

Page 5 - ASSEMBLY; position behind the unit.; ASSEMBLY—DRAG STAKE/WHEEL TRANSPORT; ITEM ORDER

5 ASSEMBLY With the exception of handlebars, controls and transport kit, your new tiller has been completely assembled at the factory. It should be noted that right and left sides are determined by the operators position behind the unit. HANDLEBARS (LOWER) (See Fig. 1) 1. Place a curved washer onto ...

Page 6 - THROTTLE CABLE; Unwind throttle cable from around engine.; STARTING INSTRUCTIONS

6 THROTTLE CABLE Unwind throttle cable from around engine. CAUTION: Be careful not to kink cable. ON/OFF SWITCH 1. Place 1 3/8” long slotted pan head screw into switch plate and down through hole in upper right hand handlebar. (See Fig. 2) 2. Place rubber isolator over screw underneath handlebar. Fo...

Page 7 - containers. Do not mix directly in fuel tank. Do not use; Fig. 6 Typical Engine Choke Symbol; Full Choke Position

7 WARNING-24:1- Disregard instructions on oil containers. Do not mix directly in fuel tank. Do not use multi-viscosity oils. Use high speed air cooled 2-cycle oil . U.S Imperial Metric Gas OilGal. Oz. Gas OilGal. Oz. Gas OilGal. Oz. 1 5 2 10 1 6 2 12 4 166 8 322 To start engine, place the unit in a ...

Page 8 - Full Choke; OPERATING TECHNIQUE AND HANDY TIPS

8 WARNING: When pulling starter rope, the rope can unexpectedly jerk back toward engine causing serious injury. To avoid this risk, carefully follow these instructions: Move rocker switch to "I" position.5. Grasp starter cord handle. Se Fig. 9 a. Pull rope out slowly until you feel drag. b. ...

Page 9 - TINE SPACERS; REMOVE SPARK PLUG WIRE BEFORE TRYING TO; ADJUSTMENTS/MAINTENANCE; KEEP YOUR AIR FILTER CLEAN!

9 TINE SPACERS The two tine spacers provided can be used to replace outside tines to narrow tilled path. DANGER! ALWAYS MOVE SWITCH TO "O" POSITION AND REMOVE SPARK PLUG WIRE BEFORE TRYING TO REMOVE OBSTRUCTIONS. CLEAN UNIT AFTER EACH OPERATION.* *ALWAYS CLEAN UNIT AFTER EACH OPERATION. This...

Page 10 - SPARK PLUG; TINE REPLACEMENT; ALWAYS MOVE SWITCH TO “O” POSITION

10 TO CLEAN SCREEN a) Wash SCREEN in water and detergent solution. b) Rinse thoroughly in clean water, then air dry. TO CLEAN AND RE-OIL FOAM FILTER a) Wash FOAM FILTER in water and detergent solution and squeeze (don’t twist) until all dirt is removed. b) Rinse thoroughly in clear water. c) Wrap in...

Page 12 - NARROW CULTIVATING; CARBURETOR ADJUSTMENT

12 IDLE SCREW NARROW CULTIVATING The two outer tines can be removed to give you a narrower cultivating width. This width is approximately 6". This will give you the ability to get between very closely spaced plants. In order to do this, pull the hairpin out of the hole in the outboard end of the...

Page 13 - THROTTLE CONTROL/THROTTLE CABLE

13 HANDLEBARS/GRIP/ON-OFF SWITCH/ THROTTLE CONTROL/THROTTLE CABLE ITEM ORDER NO. NO. DESCRIPTION QTY. REQ. 1 505 29 00-01 Grip, Handlebar 2 2 505 29 00-02 Screw, #10-24 x 1 3/8 1 3 505 29 00-03 Switch Assy, w/Mtg Plate 1 4 505 29 00-04 Isolator 1 5 505 29 00-05 Nut, Throttle/Switch Assy 1 6 505 29 0...

Page 14 - TRANSMISSION ASSEMBLY; ITEM ORDER

14 TRANSMISSION ASSEMBLY ITEM ORDER NO. NO. DESCRIPTION QTY. REQ . 1 505 29 00-18 Seal 2 2 505 29 00-19 Screw, Phillips Pan Hd 1/4-20 x 1/2 2 4 505 29 00-20 Bushing, Bronze 2 5 505 29 00-21 Drum & Hub, Clutch 1 6 505 29 00-22 Bearing, Roller 1 7 505 29 00-23 Shaft, Connecting 1 8 505 29 00-24 Bu...

Page 16 - DESCRIPTION

16 TRANSPORT KIT ASSEMBLY 1. Assemble the wheel assembly and install the wheel assembly on the tiller with the arrow up as shown. Torque: 14 ft-lb (20 N-m). Fig. 20 1 HEX BOLT, 3/8-16 X 8 inch 2 INNER COLLAR (2) 3 OUTER COLLAR (2) 4 WHEEL BAR ("UP" ARROW) 5 WHEEL (2) CLEVIS PIN 7 LOCK NUT, 3...

Page 17 - NOTES

Page 20 - WARRANTY STATEMENT

SECTION 1: LIMITED WARRANTY Husqvarna Forest & Garden Company (“Husqvarna”) warrants Husqvarna product to the original purchaser to be free fromdefects in material and workmanship from the date of purchase for the “Warranty Period” of the product as set forth below: Lifetime Warranty (Parts and ...