Husqvarna 585 - Manuals

• Never use the product above shoulder height. • Do not use the product in a situation where you cannot call for help in case of an accident. • Before moving your product, switch off the engine and lock the saw chain using the chain brake. Carry the product with the guide bar and saw chain pointing ...

Safety devices on the product WARNING: Read the warning instructions that follow before you use the product. • Do not use a product with safety devices that are damaged or do not operate correctly. • Do a check of the safety devices regularly. Refer to Maintenance and checks of the safety devices on...

Start/stop switchUse the start/stop switch to stop the engine. WARNING: The start/stop switch automatically goes back to start position. To prevent accidental start, remove the spark plug cap from the spark plug when you assemble or do maintenance on the product. Muffler WARNING: The muffler becomes...

• If you have spilled fuel or chain oil on the product. Wipe off the spillage and allow remaining fuel to evaporate. • If you have spilled fuel on yourself or on your clothes. Change your clothes and wash any part of your body that has come in contact with fuel. Use soap and water. • If the product ...

Assembly Introduction WARNING: Read and understand the safety chapter before you assemble the product. To assemble the guide bar and saw chain 1. Move the front handguard rearward to disengage the chain brake. 2. Remove the bar nuts and the clutch cover. Note: If the clutch cover is not easy to remo...

Note: The Husqvarna connectivity device has a built-in battery that cannot be replaced. Replace the Husqvarna connectivity device unit if it is necessary. 1. Remove the cylinder cover.2. Scan the QR code on the Husqvarna connectivity device. 3. Put the Husqvarna connectivity device in the holder for...

3. Make sure that the throttle lockout operates correctly and that it is not damaged. 4. Make sure that the start/stop switch operates correctly and that it is not damaged. 5. Make sure that there is no oil on the handles.6. Make sure that the vibration damping system operates correctly and that it ...

To fill the fuel tank WARNING: Obey the procedure that follows for your safety. 1. Stop the engine and let the engine become cool.2. Clean the area around the fuel tank cap. 3. Shake the container and make sure that the fuel is fully mixed. 4. Remove the fuel tank cap slowly to release the pressure....

but can also move in a different direction. It is how you use the product when the kickback occurs that causes the direction of the movement. A smaller bar tip radius decreases the force of the kickback.Use a low kickback saw chain to decrease the effects of kickback. Do not let the kickback zone to...

WARNING: If the saw chain is caught in the trunk, the product can be pushed at you. Hold the product tightly and make sure that the kickback zone of the guide bar does not touch the tree and causes a kickback. To use the cutting technique WARNING: Use full throttle when you cut and decrease to idle ...

2. Cut through the trunk on the pull stroke until the two kerfs touch. 1. 2. To cut a trunk that has support on two ends WARNING: Make sure that the saw chain does not get caught in the trunk during cutting. Obey the instructions below. 1. Cut on the pull stroke approximately ⅓ through the trunk. 2....

b) Cut on the push stroke. 3. Remove the limbs on the left side of the trunk. a) Select the applicable cutting technique for the tension in the branch. WARNING: If you are not sure about how to cut the branch, speak to a professional chainsaw operator before you continue. Refer to To cut trees and b...

4. Keep a position where the tree or branch can not hit you when the tension is released. 5. Make one or more cuts of sufficient depth necessary to decrease the tension. Cut at or near the point of maximum tension. Make the tree or branch break at the point of maximum tension. WARNING: Do not cut st...

Carburetor adjustment Because of environmental and emissions laws, your product has adjustment limitations on the carburetor adjuster screws. This decreases the harmful exhaust fumes from your product. You can only turn the adjustment screws maximum ½ turn. 1/2 1/2 H L Basic adjustments and run-in T...

2. Use a brush or shake the air filter clean. Use detergent and water to clean it fully. Note: An air filter that is used for a long time can not be fully cleaned. Replace the air filter regularly and always replace a damaged air filter. 3. Attach the air filter and make sure that the air filter sea...

To sharpen the cutters 1. Use a round file and a file gauge to sharpen the cutting teeth. Note: Refer to Accessories on page 36 for information about which file and gauge that Husqvarna recommends for your saw chain. 2. Apply the file gauge correctly on to the cutter. Refer to the instruction suppli...

Troubleshooting The engine does not start Product part to examine Possible cause Action Starter pawls The starter pawls are blocked. Adjust or replace the starter pawls. Clean around the pawls. Speak to an approved service work- shop. Fuel tank Incorrect fuel type. Drain the fuel tank and fill with ...

Transportation and storage Transportation and storage • For storage and transportation of the product and fuel, make sure that there are no leaks or fumes. Sparks or open flames, for example from electrical devices or boilers, can start a fire. • Always use approved containers for storage and transp...

Husqvarna 585 Husqvarna 592 XP Husqvarna 592 XPG Sound power level, measured dB(A) 118 118 118 Sound power level, guaranteed L WA dB(A) 119 119 119 Sound levels 3 Equivalent sound pressure level at the operator’s ear, dB(A) 112 112 112 Equivalent vibration levels, a hveq 4 Front handle, m/s 2 6.7 6....

Guide bar Saw chain Length, in/cm Pitch, in Gauge, in/mm Max. nose radius Type Length, drive links (no.) 18/46 3/8 0.058/1.5 11T or 34 mm Husqvarna S85 Husqvarna C85 68 20/50 34 mm 72 24/61 84 28/71 92 30/76 102 32/81 11T 105 36/91 115 24/61 0.404 0.063/1.6 34 mm Husqvarna H57 Husqvarna H64 76 28/71...

Declaration of Conformity EU Declaration of Conformity We, Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declare on our sole responsibility that the product: Description Chainsaws for forest service Brand Husqvarna Type / Model 585, 592 XP, 592 XPG Identification Serial numbers dati...

UK Declaration of Conformity We, Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declare on our sole responsibility that the product: Description Chainsaws for forest service Brand Husqvarna Type / Model 585, 592 XP, 592 XPG Identification Serial numbers dating from 2021 and onwards c...