Husqvarna 570, 575XP - Manuals

English – 5 WHAT IS WHAT? What is what on the chain saw? 1 5 3 6 8 7 9 15 16 11 12 13 14 10 25 24 22 21 20 19 18 17 23 4 2 28 26 27 1 Decompression valve 2 Switch for heated handle (575XPG) 3 Starter handle 4 Adjuster screws, carburetor 5 Stop switch (Ignition on/off switch.) 6 Rear handle 7 Choke c...

6 – English GENERAL SAFETY PRECAUTIONS Before using a new chain saw • Please read this manual carefully. • Check that the cutting equipment is correctly fitted and adjusted. See instructions under the heading Assembly. • Refuel and start the chain saw. See the instructions under the headings Fuel Ha...

English – 7 GENERAL SAFETY PRECAUTIONS chain saw usage if possible. Your dealer, forestry school or your library can provide information about which training materials and courses are available. Work is constantly in progress to improve the design and technology - improvements that increase your saf...

English – 9 GENERAL SAFETY PRECAUTIONS If the kickback is less violent or the kickback zone of the bar is closer to you the chain brake is designed to be activated manually by the movement of your left hand. • In the felling position the left hand is in a position that makes manual activation of the...

10 – English GENERAL SAFETY PRECAUTIONS The machine ′ s vibration damping system reduces the transfer of vibration between the engine unit/cutting equipment and the machine ′ s handle unit. The body of the chain saw, including the cutting equipment, is insulated from the handles by vibration damping...

English – 11 GENERAL SAFETY PRECAUTIONS • Keep the chain properly tensioned! If the chain is slack it is more likely to jump off and lead to increased wear on the bar, chain and drive sprocket. • Keep cutting equipment well lubricated and properly maintained! A poorly lubricated chain is more likely...

12 – English GENERAL SAFETY PRECAUTIONS Sharpening your chain and adjusting depth gauge setting General information on sharpening cutting teeth • Never use a blunt chain. When the chain is blunt you have to exert more pressure to force the bar through the wood and the chips will be very small. If th...

English – 13 GENERAL SAFETY PRECAUTIONS General advice on adjusting depth gauge setting • When you sharpen the cutting tooth (A) the depth gauge setting (C) will decrease. To maintain optimal cutting performance the depth gauge (B) has to be filed down to achieve the recommended depth gauge setting....

14 – English GENERAL SAFETY PRECAUTIONS Lubricating cutting equipment Chain oil Chain oil must demonstrate good adhesion to the chain and also maintain its flow characteristics regardless of whether it is warm summer or cold winter weather. As a chain saw manufacturer we have developed an optimal ch...

English – 15 GENERAL SAFETY PRECAUTIONS Needle bearing lubrication Both versions of sprockets have a needle bearing on the drive shaft, which has to be greased regularly (once a week). CAUTION! Use only high quality bearing grease or engine oil. Checking wear on cutting equipment Check the chain dai...

16 – English ASSEMBLY Fitting the bar and chain Check that the chain brake is in disengaged position by moving the front hand guard towards the front handle. Remove the bar nuts and remove the clutch cover (chain brake). Take off the transportation ring (A). Fit the bar over the bar bolts. Place the...

English – 17 FUEL HANDLING Fuel Note! The machine is equipped with a two-stroke engine and must always be run using a mixture of gasoline and two-stroke oil. It is important to accurately measure the amount of oil to be mixed to ensure that the correct mixture is obtained. When mixing small amounts ...

18 – English FUEL HANDLING Fueling Clean the area around the fuel cap. Clean the fuel and chain oil tanks regularly. The fuel filter must be replaced at least once a year. Contamination in the tanks causes malfunction. Make sure the fuel is well mixed by shaking the container before refuelling. The ...

English – 19 STARTING AND STOPPING Starting and stopping Cold engine Starting: The chain brake should be activated when starting the chain saw. Activate the chain brake by pushing the front hand guard forwards. Ignition; choke: Set the choke control in the choke position. This should automatically s...

20 – English STARTING AND STOPPING CAUTION! Do not pull the starter cord all the way out and do not let go of the starter handle when the cord is fully extended. This can damage the machine. Note! Pull the front hand guard towards the front handle. The chain brake is now disengaged. Your saw is read...

English – 21 WORKING TECHNIQUES Before use: 1 Check that the chain brake works correctly and is not damaged. 2 Check that the rear right hand guard is not damaged. 3 Check that the throttle lock works correctly and is not damaged. 4 Check that the stop switch works correctly and is not damaged. 5 Ch...

English – 23 WORKING TECHNIQUES 5 In order to keep control of your saw, always maintain a firm foothold. Never work on a ladder, in a tree or on any other insecure support. 6 Always use a fast cutting speed, i.e. full throttle. 7 Take great care when you cut with the top edge of the bar, i.e. when c...

24 – English WORKING TECHNIQUES Two factors decide whether the chain will jam or the object that you are cutting will split: the first is how the object is supported before and after cutting, and the second is whether it is in tension. In most cases you can avoid these problems by cutting in two sta...

English – 25 WORKING TECHNIQUES The log is supported at both ends. There is a high risk that the chain will jam. Start by cutting from above (about 1/3 of the way through). Finish by cutting from below so that the two cuts meet. Tree felling technique Safe distance The safe distance between a tree t...

26 – English WORKING TECHNIQUES Remove any undergrowth from the base of the tree and check the area for obstacles (stones, branches, holes, etc.) so that you have a clear path of retreat when the tree starts to fall. Your path of retreat should be roughly 135 degrees away from the intended felling d...

English – 27 WORKING TECHNIQUES Finish the felling cut parallel with the directional cut line so that the distance between them is at least 1/10 of the trunk diameter. The uncut section of the trunk is called the felling hinge. The felling hinge controls the direction that the tree falls in. All con...

28 – English WORKING TECHNIQUES Cutting trees and branches that are in tension Preparations: Work out which side is in tension and where the point of maximum tension is (i.e. where it would break if it was bent even more). Decide which is the safest way to release the tension and whether you are abl...

30 – English MAINTENANCE General The user must only carry out the maintenance and service work described in this manual. More extensive work must be carried out by an authorised service workshop. Carburetor adjustment Due to existing environmental and emissions legislation your chain saw is equipped...

English – 31 MAINTENANCE High speed jet H At the factory the engine is adjusted at sea level. When working at a high altitude or in different weather conditions, temperatures and atmospheric humidity, it may be necessary to make minor adjustments to the high speed jet. CAUTION! If the high speed jet...

32 – English MAINTENANCE Checking the inertia brake release With the engine turned off, hold the chain saw over a stump or other firm object. Let go of the front handle so that the bar drops towards the stump as the chain saw rotates around the rear handle. When the bar hits the stump the brake shou...

English – 33 MAINTENANCE Right hand guard Check that the right hand guard is not damaged and that there are no visible defects, such as cracks. Vibration damping system Regularly check the vibration damping units for cracks or deformation. Make sure the vibration damping units are securely attached ...

34 – English MAINTENANCE Starter Changing a broken or worn starter cord • Loosen the screws that hold the starter against the crankcase and remove the starter. • Pull out the cord approx. 30 cm (12 inches) and hook it into the notch in the rim of the pulley. Release the recoil spring by letting the ...

English – 35 MAINTENANCE Air filter The air filter must be regularly cleaned to remove dust and dirt in order to avoid: • Carburettor malfunctions • Starting problems • Loss of engine power • Unnecessary wear to engine parts • Excessive fuel consumption. • Remove the air filter after taking off the ...

36 – English MAINTENANCE Adjustment of the oil pump The oil pump is adjustable. Adjustments are made by turning the screw using a screwdriver or combination spanner. The machine is supplied from the factory set to 1 turn open. Turning the screw clockwise will reduce the oil flow and turning the scre...

English – 37 MAINTENANCE Winter use Running problems can occur when using the machine in the cold and snowy conditions caused by: • Too low engine temperature. • Icing of the air filter and carburetor. Special measures are therefore often required: • Preheat the intake air to the carburetor by using...

38 – English MAINTENANCE Maintenance schedule The following is a list of the maintenance that must be performed on the machine. Most of the items are described in the Maintenance section. Daily maintenance Weekly maintenance Monthly maintenance Clean the outside of the machine. On chain saws without...

English – 39 TECHNICAL DATA Technical data 570 575XP Engine Cylinder displacement, cu.in/cm 3 4,1/68 4,5/73,5 Cylinder bore, inch/mm 1,93/49 2,0/51 Stroke, inch/mm 1,42/36 1,42/36 Idle speed, rpm 2700 2700 Power, kW/hp @ rpm 3,6/4,9 @ 9600 4,0/5,5 @ 9600 Ignition system Manufacturer of ignition syst...

English – 41 FEDERAL EMISSION CONTROL WARRANTY STATEMENT YOUR WARRANTY RIGHTS AND OBLIGATIONS The EPA (The US Environmental Protection Agency), Environment Canada and Husqvarna Forest & Garden are pleased to explain the emissions control system warranty on your 2001 and later small nonroad engin...

42 – English AMERICAN STANDARD SAFETY PRECAUTIONS ´®z+H8)¶5m¨ ´®z+H8)¶5m¨ Safety precautions for chain saw users (ANSI B 175.1-2000 Annex C) Kickback safety precautions With a basic understanding of kickback, you can reduce or eliminate the element of surprise. Sudden surprise contributes to acciden...