Husqvarna 535FBX - Manuals

• Do a visual check for damage and deformation.• Make sure that the muffler is correctly attached to the product. • If the muffler on your product has a spark arrester screen, do a visual check. Replace the spark arrester screen if it is damaged.a) Clean the spark arrester screen if it is blocked. A...

To set the product in transport position 1. Loosen the knob and remove the top part of the load reducer. 2. Attach the top part (B) of the load reducer to the bottom part (A) of the load reducer. B A 3. Turn the knob 3 turns or more to loosen the coupling on the shaft. 4. Push and hold the button (C...

9. Hang the throttle hand guard on the frame. Operation 535FBX Introduction WARNING: Before you operate the product, you must read and understand the safety chapter. To check before starting 1. Inspect the working area. Remove any objects that could be thrown out. 2. Check the saw chain. Never use b...

2. Move the choke control up into choke position. WARNING: Be careful, risk of cut injuries. The saw chain starts to rotate immediately when you start the engine with the choke. To start the product WARNING: Read the warning instructions in the safety chapter before you start the product (refer to S...

Maintenance Daily Weekly Monthly Clean the external surface. X Make sure that the throttle trigger lock and the throttle works correctly. X Do a check of the stop switch to make sure that it works correctly. X Make sure that the saw chain does not rotate at idle speed. X Clean the air filter. Replac...

3. Adjust the idle speed with the idle adjustment screw T which is identified with "T" mark. Turn the idle adjustment screw clockwise until the saw chain starts to turn. T 4. Turn the idle adjustment screw counterclockwise until the saw chain stops. The idle speed is correct when the engine ...

To lubricate the drive shaft 1. Pull up the knob and remove the drive shaft sleeve from the clutch cover. a) Shake or pull the drive shaft out of the drive shaft sleeve. 2. Lubricate the drive shaft. 3. Push and turn the drive shaft at the same time to put it back in the drive shaft sleeve. Keep app...

6. Make sure that the bar tip sprocket turns freely and that the lubricating hole in the bar tip sprocket is not blocked. Clean and lubricate if it is necessary. 7. Turn the guide bar daily to extend its life cycle. To sharpen the saw chain Information about the guide bar and saw chain WARNING: Use ...

Troubleshooting The engine does not start Check Possible cause Procedure Stop switch. The stop switch is in the stop posi- tion. Let an approved service agent re- place the stop switch. Fuel tank. Incorrect fuel type. Drain the fuel tank and fill with cor- rect fuel. Spark plug and cylinder. The spa...

2. Disassemble and clean the saw chain and the groove in the guide bar. CAUTION: If the saw chain and guide bar are not cleaned, they can become rigid or blocked. 3. Attach the transportation guard.4. Clean the product. Refer to Maintenance 535RBX on page 18 for instructions. 5. Do a complete servic...

Accessories Recommended cutting equipment Recommended guide bar and saw chain combination. Guide bar Saw chain Length, in. Pitch, in. Gauge, mm Max. nose ra- dius Type Length, drive links, no. 13 0.325 1.3 10T Husqvarna H30 56 Husqvarna SP33G Filing equipment and filing angles Husqvarna file gauge g...

Declaration of Conformity 535FBX EU Declaration of Conformity We, Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declare on our sole responsibility that the product: Description Pole saw Brand Husqvarna Type / Model 535FBX Identification Serial numbers dating from 2022 and onwards co...

Declaration of conformity We, Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declare on our sole responsibility that the product: Description Pole saw Brand Husqvarna Type / Model 535FBX Identification Serial numbers dating from 2022 and onwards complies fully with the following UK r...

Product overview TA1100 1 3 2 6 7 9 10 8 11 4 5 4 1 1. Trimmer head2. Grease filler cap, bevel gear3. Bevel gear4. Cutting attachment guard5. Shaft6. Handle adjustment 7. Loop handle8. Operator's manual9. Hex key10. Locking pin11. Drive disc Safety TA1100 Safety instructions for operation WARNING: R...

Trimmer head WARNING: Always make sure the trimmer line is wound tightly and evenly around the drum to prevent harmful vibration. • Only use recommended trimmer heads and trimmer lines. • Only use recommended cutting attachments.• Smaller machines requires small trimmer heads and vice versa. • The l...

7. Turn the trimmer head /plastic blades (H) in the opposite direction from which the trimmer head/ plastic blades rotates. H H Operation TA1100 Grass trimming with a trimmer head To trim the grass 1. Hold the trimmer head immediately above the ground at an angle. Do not push the trimmer line into t...

3. Move the trimmer head from side to side and sweep the grass. WARNING: Clean the trimmer head cover each time you assemble new trimmer line to prevent unbalance and vibrations in the handles. Also do a check of the other parts of the trimmer head and clean it if necessary. Technical data TA1100 Te...

Declaration of Conformity TA1100 EU Declaration of Conformity We, Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declare on our sole responsibility that the product: Description Pole saw Brand Husqvarna Type / Model 535FBX Identification Serial numbers dating from 2022 and onwards co...