Husqvarna 525P4S - Manuals - manualsarea.com

Page 2 - Intended use

Contents Introduction..................................................................... 2Safety..............................................................................4Assembly........................................................................ 9Operation...................................

Page 3 - Symbols on the product

19. Chain oil tank20. Operator's manual21. Transport guard, bar22. Hex key23. Combination wrench24. Combination wrench, chain tensioner25. Harness 525P5S26. Harness 525P4S27. Shaft coupling28. Impact guard29. Spark plug cap and spark plug Symbols on the product WARNING! This product is dangerous. In...

Page 4 - Safety

Note: Other symbols/decals on the product refer to certification requirements for other commercial areas. Euro V Emissions WARNING: Tampering with the engine voids the EU type-approval of this product. Product damage We are not responsible for damages to our product if: • the product is incorrectly ...

Page 9 - Assembly; To assemble the cutting head

and chain drive sprocket. Refer to To tension the chain on page 21. • Do maintenance on the cutting equipment regularly and keep it correctly lubricated. If the saw chain is not correctly lubricated, the risk of wear on the guide bar, saw chain and chain drive sprocket increases. Assembly To assembl...

Page 11 - To assemble the impact guard; Operation; Introduction

4. Pull the attachment straight out of the coupling. C To assemble the impact guard 1. Assemble the guard with 3 screws. 2. Tighten the screws to 30 ft/lbs (4 Nm).3. Tighten the screws again when the product has been in use for about 20 hours. Operation Introduction WARNING: Before you operate the p...

Page 13 - To use the product

To use the correct chain oil WARNING: Do not use waste oil, which can cause injury to you and the environment. Waste oil also causes damage to the oil pump, the guide bar and the saw chain. WARNING: The saw chain can break if the lubrication of the cutting equipment is not sufficient. Risk of seriou...

Page 15 - To stop the product; Maintenance

To stop the product 1. Move the stop switch into the stop position to stop the engine. CAUTION: The stop switch automatically goes back to its initial position. In order to prevent accidental starting, the spark plug cap must be removed from the spark plug when assembling, checking and/or maintenanc...

Page 18 - To check the chain drive sprocket

To clean the air filter CAUTION: An air filter that is damaged, very dirty, or soaked with fuel must always be replaced. Clean the air filter from dirt and dust regularly. This prevents carburetor malfunctions, starting problems, loss of engine power, wear to engine parts and more fuel consumption t...

Page 23 - Troubleshooting; The engine does not start; Transportation, storage and disposal; Transportation and storage

Troubleshooting The engine does not start Check Possible cause Procedure Stop switch. The stop switch is in the stop posi- tion. Let an approved service agent re- place the stop switch. Fuel tank. Incorrect fuel type. Drain the fuel tank and fill with cor- rect fuel. Spark plug and cylinder. The spa...

Page 24 - Technical data

2. Disassemble and clean the saw chain and the groove in the guide bar. CAUTION: If the saw chain and guide bar are not cleaned, they can become rigid or blocked. 3. Attach the transportation guard.4. Clean the product. Refer to Maintenance on page 15 for instructions. 5. Do a complete servicing of ...

Page 25 - Accessories; Guidebar and saw chain combinations

525P4S 525P5S Equivalent vibration levels (a hv,eq ) at handles, measured according to ISO 22867, m/s 2 : Equipped with approved accessory (original), front/rear 3.6/3.5 3.6/3.5 Accessories Guidebar and saw chain combinations Recommended guide bar and saw chain combination. Guide bar Saw chain Lengt...

Page 26 - Declaration of Conformity; EU Declaration of Conformity

Declaration of Conformity EU Declaration of Conformity We, Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declare on our sole responsibility that the product: Description Pole saws Brand Husqvarna Type / Model 525P4S, 525P5S Identification Serial numbers dating from 2022 and onwards ...

Page 27 - UK Declaration of Conformity

UK Declaration of Conformity We, Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declare on our sole responsibility that the product: Description Pole saws Brand Husqvarna Type / Model 525P4S, 525P5S Identification Serial numbers dating from 2022 and onwards complies fully with the fo...