Husqvarna 435i - Manuals

are on a ladder or in a tree. Do not use the product if you are not on stable ground. • Working in a tree requires the use of special cutting and working techniques which must be observed in order to reduce the increased risk of personal injury. Never work in a tree unless you have received specific...

• Most chainsaw accidents occur when the saw chain touches the operator. You must use approved personal protective equipment during operation. Personal protective equipment does not give you full protection from injuries but it decreases the degree of injury if an accident occurs. Speak to your serv...

Safety instructions for the cutting equipment WARNING: Read the warning instructions that follow before you use the product. • Only use approved guide bar/saw chain combinations and filing equipment. Refer to Technical data on page 33 for instructions. • Use protective gloves when you use or do main...

Operation Introduction WARNING: Read and understand the safety chapter before you use the product. To do a function check before you use the product 1. Do a check of the chain brake (A) to make sure that it operates correctly and that it is not damaged. 2. Do a check of the rear right hand guard (B)...

WARNING: No saw chain fully prevents kickback. Always obey the instructions. Common questions about kickback • Will the hand always engage the chain brake during a kickback?No. It is necessary to use some force to push the front hand guard forward. If you do not use the force necessary, the chain br...

WARNING: There is a high accident risk when you use the limbing technique. Refer to To cut trees and branches that are in tension on page 22 for instructions how to prevent kickback. WARNING: Cut limbs one by one. Be careful when you remove small limbs and do not cut bushes or many small limbs at th...

1 2 2 1 3 To fell a tree Husqvarna recommends you to make the directional cuts and then use the safe corner method when you fell a tree. The safe corner method helps you to make a correct felling hinge and control the felling direction. WARNING: Do not fell trees with a diameter that is more than tw...

2. Figure out where the point of maximum tension is. 3. Examine which is the safest procedure to release the tension. Note: In some situations the only safe procedure is to use a winch and not your product. 4. Keep a position where the tree or branch can not hit you when the tension is released. 5. ...

Maintenance Introduction WARNING: Read and understand the safety chapter before you do maintenance on the product. Maintenance schedule WARNING: Remove the battery before you do maintenance. The following is a list of the maintenance steps that you must do on the product. See Maintenance on page 24 ...

Maintenance and checks of the safety devices on the product To do a check of the front hand guard Regularly do a check of the front hand guard and the inertia brake release.1. Make sure that the front hand guard does not have damages such as cracks. 2. Make sure that the front hand guard moves freel...

3. Make sure that the power trigger is locked at the idle position when the power trigger lockout is released. 4. Start the product and apply full power.5. Release the power trigger and make sure that the saw chain stops and stays stationary. WARNING: If the saw chain rotates when the power trigger ...

To sharpen the saw chain Information about the guide bar and saw chain WARNING: Use protective gloves when you use or do maintenance on the saw chain. A saw chain that does not move can also cause injuries. Replace a worn or damaged guide bar or saw chain with the guide bar and saw chain combination...

7. Turn the guide bar daily to extend its life cycle. Troubleshooting User interface LED screen Possible faults Possible solution The warning in- dicator flashes. Chain brake is engaged. Disengage the chain brake. Temperature deviation. Let the product to cool down. Overload. The saw chain can not m...

Battery charger LED display Possible faults Possible action Warning indicator flashing. Temperature deviation. Use the battery in surroundings where temperatures are between 5°C/41°F and 40°C/104°F. Warning indicator lit. Turn to your servicing dealer. Transportation, storage and disposal Transporta...

435i Features Low energy mode savE Lubrication system Type of oil pump Automatic Oil tank capacity, l/cm 3 0.18/180 Weight Chainsaw without battery, guide bar, saw chain and empty chain oil tank, kg 2.7/2.8 (Tool / Tool less drive sprock- et cover) Water protection level IPX4 Yes Noise emissions 2 S...

Declaration of Conformity EU Declaration of Conformity We, Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declare on our sole responsibility that the product: Description Battery-operated chainsaw Brand Husqvarna Type / Model 435i Identification Serial numbers dating from 2024 and on...

UK Declaration of Conformity We, Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declare on our sole responsibility that the product: Description Battery-operated chainsaw Brand Husqvarna Type / Model 435i Identification Serial numbers dating from 2024 and onwards complies fully with ...