Husqvarna 370BTS - Manuals

Husqvarna 370BTS – Manual in PDF format online.

Manuals:

Manual

Manual Husqvarna 370BTS

Summary

Page 2 - EC-declaration of conformity

English 2 EC-declaration of conformity [ 3 30BT] (Applies to Europe only) Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel +46-36-146500, declares under sole responsibility that the blowers Husqvarna 3 30BT with serial numbers dating 2007 and onwards (the year is clearly stated on the rating plate, fo...

Page 4 - Contents

English 4 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 SAFETY FIRST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Notes on types of war...

Page 5 - SAFETY FIRST; Notes on types of warnings; WARNING; Symbols; IMPORTANT; Warning labels on the machine

English 5 SAFETY FIRST Instructions contained in warnings within this manual and warning seals marked with a symbol on the blower concern critical points which must be taken into consideration to prevent possible serious bodily injury, and for this reason you are requested to read all such instructi...

Page 6 - Safety Precautions

English 6 For safe operation and maintenance, symbols are carved in relief on the machine. Using to these indications, please be careful not to make a mistake. (a) The port to refuel the "MIX GASOLINE" Position: FUEL TANK CAP (b) The direction to close the choke Position: INTAKE CUP (c) The ...

Page 7 - WORKING CONDITIONS; WORKING CIRCUMSTANCE; NOTE; WORKING PLAN

English 7 WORKING CONDITIONS 1. Refrain from operating the blower if you are tired, ill, or upset, or if you are under the influence of alcohol, drugs or medication 2. To reduce the risk of hearing loss associated with sound levels, hearing protection is required. 3. To reduce the risk of injury ass...

Page 8 - BEFORE STARTING THE ENGINE; USING THE PRODUCT

English 8 BEFORE STARTING THE ENGINE • Each time before starting the engine, inspect the entire unit to see if every part is in good order and is securely tightened in place. If any damage is found in the fuel line, the exhaust line, or the ignition wiring, do not use the blower until it has been re...

Page 9 - MAINTENANCE; TRANSPORTATION

English 9 MAINTENANCE 1. In order to maintain your product in proper working order, perform the maintenance and checking operations described in the manual at regular intervals. 2. Always be sure to turn off the engine and disconnect the spark plug before performing any maintenance or checking proce...

Page 10 - DISPOSAL

English 10 1. Frame2. Harness3. Spark Plug Cap4. Throttle Lever5. Guard Net6. Choke Lever7. Air Cleaner8. Volute Case, Cover9. “CAUTION” Label10. Elbow11. Fuel Tank12. Recoil Starter 13. Stop Switch with Throttle Position Setting14. Engine Cover15. Handle Bar (Option)16. Fan17. Shock Absorber (Sprin...

Page 14 - Technical data

English 14 • The data shown above are those in the case of one straight pipe. • Specifications are subject to change without notice. MODEL 3 30BT 3 50BT 3 70BT S 3 80BT S Dimensions (L x W x H) mm (in) 295x387x432 (11.6x15.2x17) 351x446x479 (13.8x17.6x18) 365x464x485 (14x18x19) 410x509x497 (16.1x20x...

Page 15 - SWIVEL JOINT; THROTTLE LEVER; Assembly

English 15 SWIVEL JOINT 1. Connect the blower and swivel joint with flexible hose. Clamp both ends of the flexible hose securely with the hardware supplied with the unit. NOTE A light lubricant may be used to ease assembly of flexible hose to blower tube. THROTTLE LEVER 1. Set up the throttle ho...

Page 16 - HARNESS

English 16 HARNESS NOTE The harness must always be worn when working with the machine. Failure to do so means you will be unable to maneuver safely and this can result in injury to yourself or others. A correctly adjusted harness and machine significantly facilitates the work. Adjust the harness t...

Page 17 - FUEL; HOW TO MIX FUEL; FUELING THE UNIT; Fuel

English 17 FUEL WARNING • Gasoline is very flammable. Avoid smoking or bringing any flame or sparks near fuel. Make sure to stop the engine and allow it cool before refueling the unit. Select outdoor bare ground for fueling and move at least 10ft (3m) away from the fueling point before starting th...

Page 18 - STARTING ENGINE; Operation

English 18 STARTING ENGINE IMPORTANT • Avoid operating the blower with the flexible tube and swivel joint disconnected. That will reduce the cooling air and the engine could be damaged by overheating. 1. Push the primer bulb until fuel flows out in the clear tube.2. When the engine is cool, close ...

Page 19 - ADJUSTING IDLE SPEED; STOPPING ENGINE

English 19 ADJUSTING IDLE SPEED [ 3 30BT] • The idling speed is set for 3000 rpm at the factory. If it is necessary to adjust the idle speed, use the adjustment screw on the top side of carburetor. (1) Idling Adjustment Screw [ 3 50BT] [ 3 70BT S ] [ 3 80BT S ] • The idling speed is set for 2200 r...

Page 20 - AIR CLEANER; Maintenance

English 20 Maintenance, replacement, or repair of the emission control device and systems may be performed by any non-road engine repair establishment or individual. WARNING Make sure that the engine has stopped and is cool before performing any service to the blower. Contact with rotating blower fa...

Page 21 - FUEL FILTER; SPARK PLUG; MUFFLER; SPARK ARRESTER

English 21 [ 3 70BT S ] [ 3 80BT S ] (F26) 1. Unscrew 2 knob bolts and remove the air cleaner cover. Then remove the prefilter mounted inside the air cleaner cover. (1) Knob Bolt (2) Prefilter (3) Inner Case [ 3 80BT S ] (4) Paper Filter 2. Wash the prefilter in fresh, non flammable cleaning solutio...

Page 22 - AIR INLET NET; IGNITION COIL AIR GAP INSPECTION; SHOLDER STRAP; Storage

English 22 AIR INLET NET IMPORTANT • Blown air is taken in from the air inlet net. If the air flow drops during opera- tion, stop the engine and inspect the air inlet net for blockage by obstacles. • Note that failure to remove any such obstacles may result in the engine becoming overheated and da...