Husqvarna 365 EPA I - Manuals

6 – English WHA T IS WHA T? What is what on the chain saw? 1 Cylinder cover 2 Front handle 3 Chain brake and front hand guard 4 Starter 5 Chain oil tank 6 Starter handle 7 Adjuster screws carburetor 8 Choke control/Start throttle lock 9 Rear handle 10 Stop switch (Ignition on/off switch.) 11 Fuel ta...

English – 7 GENERAL SAFETY PRECA UTIONS Bef ore using a new chain saw • Please read this manual carefully. • Check that the cutting equipment is correctly fitted and adjusted. See instructions under the heading Assembly. • Refuel and start the chain saw. See the instructions under the headings Fuel ...

8 – English GENERAL SAFETY PRECAUTIONS chain saw usage if possible. Your dealer, forestry school or your library can provide information about which training materials and courses are available. Work is constantly in progress to improve the design and technology - improvements that increase your saf...

10 – English GENERAL SAFETY PRECAUTIONS Will my inetria activated chain brake always activate during kickback in the event of a kickback? No. First your brake must be in working order. Testing the brake is simple, see instructions under the heading Checking, maintaining and servicing chain saw safet...

English – 11 GENERAL SAFETY PRECAUTIONS Stop switch Use the stop switch to switch off the engine. Muffler The muffler is designed to keep noise levels to a minimum and to direct exhaust fumes away from the user. In areas with a hot, dry climate there is a high risk of fires. These areas are sometime...

12 – English GENERAL SAFETY PRECAUTIONS Chain A chain is made up of a number of links, which are available in standard and low-kickback versions. Some terms that describe the bar and chain To maintain the safety features of the cutting equipment, you should replace a worn or damaged bar or chain wit...

English – 13 GENERAL SAFETY PRECAUTIONS 2 Cutting angle 3 File position 4 Round file diameter It is very difficult to sharpen a chain correctly without the right equipment. We recommend that you use our file gauge. This will help you obtain the maximum kickback reduction and cutting performance from...

14 – English GENERAL SAFETY PRECAUTIONS Tensioning the chain The more you use a chain the longer it becomes. It is therefore important to adjust the chain regularly to take up the slack. Check the chain tension every time you refuel. NOTE! A new chain has a running-in period during which you should ...

English – 15 GENERAL SAFETY PRECAUTIONS Checking chain lubrication • Check the chain lubrication each time you refuel. See instructions under the heading Lubricating the bar tip sprocket. Aim the tip of the bar at a light coloured surface about 20 cm (8 inches) away. After 1 minute running at 3/4 th...

English – 17 ASSEMBLY Fitting the bar and chain Check that the chain brake is in disengaged position by moving the front hand guard towards the front handle. Remove the bar nuts and remove the clutch cover (chain brake). Take off the transportation ring (A). Fit the bar over the bar bolts. Place the...

18 – English FUEL HANDLING Fuel Note! The machine is equipped with a two-stroke engine and must always be run using a mixture of gasoline and two-stroke oil. It is important to accurately measure the amount of oil to be mixed to ensure that the correct mixture is obtained. When mixing small amounts ...

English – 19 FUEL HANDLING Fueling Clean the area around the fuel cap. Clean the fuel and chain oil tanks regularly. The fuel filter must be replaced at least once a year. Contamination in the tanks causes malfunction. Make sure the fuel is well mixed by shaking the container before refuelling. The ...

20 – English STARTING AND STOPPING Starting and stopping Cold engine Starting: Ignition: Slide the ignition switch to the left. Choke: Set the choke control in the choke position. Start throttle: The correct choke/start throttle setting is obtained by moving the control to the choke position. If the...

English – 21 STARTING AND STOPPING • Never start a chain saw unless the bar, chain and all covers are fitted correctly. See instructions under the heading Assembly. Without a bar and chain attached to the chain saw the clutch can come loose and cause serious injury. • The chain brake should be activ...

22 – English WORKING TECHNIQUES Before use: 1 Check that the chain brake works correctly and is not damaged. 2 Check that the rear right hand guard is not damaged. 3 Check that the throttle lockout works correctly and is not damaged. 4 Check that the stop switch works correctly and is not damaged. 5...

24 – English WORKING TECHNIQUES 8 Unless the user resists this pushing force there is a risk that the chain saw will move so far backwards that only the kickback zone of the bar is in contact with the tree, which can lead to a kickback. Cutting with the bottom edge of the bar, i.e. from the top of t...

English – 25 WORKING TECHNIQUES Limbing When limbing thick branches you should use the same approach as for cutting. Cut difficult branches piece by piece. Cutting If you have a pile of logs, each log you attempt to cut should be removed from the pile, placed on a saw horse or runners and cut indivi...

26 – English WORKING TECHNIQUES Tree felling technique Safe distance The safe distance between a tree that is to be felled and anyone else working nearby is at least 2 1/2 tree lengths. Make sure that no-one else is in this ”risk zone” before or during felling. Felling direction The aim is to fell t...

English – 27 WORKING TECHNIQUES Felling Felling is done using three cuts. First you make the directional cuts, which consist of the top cut and the bottom cut, then you finish with the felling cut. By placing these cuts correctly you can control the felling direction very accurately. Directional cut...

28 – English WORKING TECHNIQUES We recommend that you use a bar that is longer than the diameter of the tree, so that you can make the felling cut and directional cuts with single cutting strokes. See instructions under the heading Technical data section to find out which lengths of bar are recommen...

English – 29 WORKING TECHNIQUES How to avoid kickback What is kickback? The word kickback is used to describe the sudden reaction that causes the chain saw and bar to jump off an object when the upper quadrant of the tip of the bar, known as the kickback zone, touches an object. Kickback always occu...

30 – English MAINTENANCE General The user must only carry out the maintenance and service work described in this manual. Carburetor adjustment Due to existing environmental and emissions legislation your chain saw is equipped with movement limiters on the carburetor adjuster screws. These limit the ...

English – 31 MAINTENANCE High speed jet H At the factory the engine is adjusted at sea level. When working at a high altitude or in different weather conditions, temperatures and atmospheric humidity, it may be necessary to make minor adjustments to the high speed jet. CAUTION! If the high speed jet...

32 – English MAINTENANCE Checking the inertia brake release With the engine turned off, hold the chain saw over a stump or other firm object. Let go of the front handle so that the bar drops towards the stump as the chain saw rotates around the rear handle. When the bar hits the stump the brake shou...

English – 33 MAINTENANCE Right hand guard Check that the right hand guard is not damaged and that there are no visible defects, such as cracks. Vibration damping system Regularly check the vibration damping units for cracks or deformation. Make sure the vibration damping units are securely attached ...

34 – English MAINTENANCE Starter Changing a broken or worn starter cord • Loosen the screws that hold the starter against the crankcase and remove the starter. • Pull out the cord approx. 30 cm (12 inches) and hook it into the notch in the rim of the pulley. Release the recoil spring by letting the ...

English – 35 MAINTENANCE Air filter The air filter must be regularly cleaned to remove dust and dirt in order to avoid: • Carburettor malfunctions • Starting problems • Loss of engine power • Unnecessary wear to engine parts • Excessive fuel consumption. • Remove the air filter after taking off the ...

36 – English MAINTENANCE Cooling system To keep the working temperature as low as possible the machine is equipped with a cooling system. The cooling system consists of: 1 Air intake on the starter. 2 Air guide plate. 3 Fins on the flywheel. 4 Cooling fins on the cylinder. 5 Cylinder cover (directs ...

English – 37 MAINTENANCE Heated handles (372XPG) On models with the designation XPG/G, the front as well as the rear handle are equipped with electric heating coils. These are fed with electrical current from an integrated generator in the chain saw. When the red mark on the switch is visible, the h...

38 – English MAINTENANCE Maintenance schedule The following is a list of the maintenance that must be performed on the machine. Most of the items are described in the Maintenance section. Daily maintenance Weekly maintenance Monthly maintenance Clean the outside of the machine. On chain saws without...

English – 39 TECHNICAL DATA Technical data 365 372XP Engine Cylinder displacement, cu.in/cm 3 3,97/65,1 4,31/70,7 Cylinder bore, inch/mm 1,89/48 1,97/50 Stroke, inch/mm 1,42/36 1,42/36 Idle speed, rpm 2700 2700 Power, kW/ rpm 3,4/9300 3,9/9600 Ignition system Manufacturer of ignition system SEM SEM ...

40 – English TECHNICAL DATA Recommended original and replacement bar and chain combinations These Husqvarna chain saw models are in the ANSI category of saws above 3,8 cu. in. and are not required to comply with low kickback performance requirements. However, for these models we recommend the follow...

English – 41 FEDERAL EMISSION CONTROL WARRANTY STATEMENT YOUR WARRANTY RIGHTS AND OBLIGATIONS The EPA (The US Environmental Protection Agency), Environment Canada and Husqvarna Forest & Garden are pleased to explain the emissions control system warranty on your 2001 and later small nonroad engin...

42 – English AMERICAN STANDARD SAFETY PRECAUTIONS ´®z+Rse¶5S¨ ´®z+Rse¶5S¨ Safety precautions for chain saw users (ANSI B 175.1-2000 Annex C) Kickback safety precautions With a basic understanding of kickback, you can reduce or eliminate the element of surprise. Sudden surprise contributes to acciden...