Husqvarna 326SX-Series - Manuals

English – 5 WHAT IS WHAT? What is what on the sweeper? 1 Blade 2 Sweeper roller 3 Roller shaft 4 Pin 5 Hairpin spring 6 Plastic sleeve 7 Tube 8 Gearbox 9 Split Pin 10 Loop handle 11 Handle adjustment 12 Stop switch 13 Throttle lock 14 Cylinder cover 15 Starter handle 16 Fuel tank 17 Air fi lter cove...

6 – English SAFETY INSTRUCTIONS Important Personal protective equipment HEARING PROTECTION Wear hearing protection that provides adequate noise reduction. EYE PROTECTION Always wear approved eye protection. If you use a visor then you must also wear approved protective goggles. Approved protective g...

English – 7 SAFETY INSTRUCTIONS Machine ′′′′ s safety equipment This section describes the machine ′ s safety equipment, its purpose, and how checks and maintenance should be carried out to ensure that it operates correctly. See the ”What is what?” section to locate where this equipment is positione...

8 – English SAFETY INSTRUCTIONS The machine ′ s vibration damping system reduces the transfer of vibration between the engine unit/cutting equipment and the machine ′ s handle unit. Regularly check the vibration damping units for cracks or deformation. Check that the vibration damping element is und...

9 – English ASSEMBLY Assembling the sweeper • Slide the plastic sleeve (wear protection) (A) onto the shaft (B). • Fit the gearbox (C) on the tube (B). Tighten clamp screw (D) at the gearbox. Tighten the two locking screws (E) on the gearbox. • Press one of the roller shafts (F) onto one of the two ...

10 – English FUEL HANDLING Fuel safety Never start the machine: 1 If you have spilt fuel on it. Wipe off the spillage and allow remaining fuel to evaporate. 2 If you have spilt fuel on yourself or your clothes, change your clothes. Wash any part of your body that has come in contact with fuel. Use s...

English – 11 FUEL HANDLING Mixing • Always mix the gasoline and oil in a clean container intended for fuel. • Always start by fi lling half the amount of the gasoline to be used. Then add the entire amount of oil. Mix (shake) the fuel mixture. Add the remaining amount of gasoline. • Mix (shake) the ...

12 – English STARTING AND STOPPING Starting and stopping Starting Primer bulb: Press the primer bulb repeatedly until fuel begins to fi ll the bulb. The bulb need not be completely fi lled. Choke: Set the choke control in the choke position. Hold the body of the machine on the ground using your left...

English – 13 WORKING TECHNIQUES General working instructions Basic safety rules 1 Look around you: • To ensure that people, animals or other things cannot affect your control of the machine. • To prevent the above-mentioned from coming into contact with the sweeper or being hit by loose objects that...

English – 15 MAINTENANCE Carburetor Your Husqvarna product has been designed and manufactured to speci fi cations that reduce harmful emissions. After the engine has used 8-10 tanks of fuel the engine will be run-in. To ensure that it continues to run at peak performance and to minimise harmful exha...

16 – English MAINTENANCE Low speed jet L Try to fi nd the highest idling speed, turning the low speed needle L clockwise respectively counter-clockwise. When the highest speed has been found, turn the low speed needle L 1/4 turn counter-clockwise. CAUTION! If the sweeper rollers rotates/moves while ...

English – 17 MAINTENANCE Muf fl er CAUTION! Some muf fl ers are fi tted with a catalytic converter. See chapter on Technical data to see whether your machine is fi tted with a catalytic converter. The muf fl er is designed to reduce the noise level and to direct the exhaust gases away from the opera...

18 – English MAINTENANCE Air fi lter The air fi lter must be regularly cleaned to remove dust and dirt in order to avoid: • Carburettor malfunctions • Starting problems • Loss of engine power • Unnecessary wear to engine parts • Excessive fuel consumption. Clean the fi lter every 8 hours, or more re...

English – 19 MAINTENANCE Maintenance schedule The following is a list of the maintenance that must be performed on the machine. Most of the items are described in the Maintenance section. The user must only carry out the maintenance and service work described in this manual. More extensive work must...

20 – English TECHNICAL DATA Technical data Note 1: Equivalent noise pressure level is calculated as the time-weighted energy total for noise pressure levels under various working conditions with the following time distribution: 1/2 idle and 1/2 max. speed. Technical data 326SX Engine Cylinder displa...

English – 21 FEDERAL EMISSION CONTROL WARRANTY STATEMENT YOUR WARRANTY RIGHTS AND OBLIGATIONS The EPA (The US Environmental Protection Agency), Environment Canada and Husqvarna Forest & Garden are pleased to explain the emissions control system warranty on your 2001 and later small nonroad engin...