Husqvarna 325 L XT-Series - Manuals

English – 7 SAFETY INSTRUCTIONS 6. Cutting equipment The section describes how through correct maintenance andthrough using the right type of cutting equipment you can:• Obtain maximum clearing capacity.• Increase the service life of the cutting equipment. Two basic rules: 1)Only use the cutting and...

8 – English SAFETY INSTRUCTIONS General safety instructions Transport and storage • Store and transport the machine and fuel so that any leakage or fumes do not risk coming into contact with sparks ornaked flames. For example, electric machines, electricmotors, electrical switches/power switches, he...

English – 9 ! General working instructions SAFETY INSTRUCTIONS Basic working techniques • Always drop to idling speed after each working operation. Longer periods running at full throttle without loading theengine (that is without resistance, which the engine feelsfrom the cutting equipment when tri...

English – 11 WHAT IS WHAT? What is what on the trimmer? 1. Trimmer head 2. Grease filler cap 3. Angle gear 4. Spray guard 5. Shaft 6. Loop handlebar 7. Throttle 8. Stop switch 9. Throttle trigger lock 10. Cylinder cover 11. Starter handle 12. Fuel tank 13. Choke 14. Air purge 15. Air filter cover 16...

12 – English ASSEMBLY Assembly of the trimmer head ! WARNING!Under no circumstances may the cuttingequipment be used without an approvedguard fitted. See the chapter “Technical data”. If the wrong guard or a defectiveguard is fitted this can cause seriouspersonal injury. Assembling the loop handleba...

English – 15 FUEL HANDLING Fuel mixture ! WARNING!Always provide good ventilation whenhandling fuel. NOTE! The machine is fitted with a two-stroke engine and mustalways be run on a mixture of gasoline and two-stroke oil. It isimportant to measure the quantity of oil accurately, to ensurethe correct ...

16 – English START AND STOP Cold engine IGNITION:Set the stop switch to thestart position.CHOKE:Set the choke control in thechoke position.AIR PURGE:Press the air purgediaphragm repeatedly untilfuel begins to fill thediaphragm. The diaphragmneed not be completelyfilled. Warm engine Use the same star...

English – 17 Fine adjustment • When the machine has been ”run-in” the carburetor should be finely adjusted. The fine adjustment should be carried out by qualified person. First adjust the L-jet, then the idling screw T and then the H-jet. Conditions • Before any adjustments are made the airfilter sh...

18 – English Correctly adjusted carburetor A correctly adjusted carburetor means that the machineaccelerates without hesitation and the machine 4-cycles a littleat max speed. Furthermore, the cutting attachment must notrotate/move at idling. A too lean adjusted low speed needle Lmay cause starting d...

English – 19 MAINTENANCE Cooling system To maintain as low opera-ting temperature as possiblethe engine is equipped witha cooling system.The cooling system consistsof:1. An air intake on the starter unit. 2. Cooling fins on the flywheel. 3. Cooling fins on the cylinder 4. Cylinder cover (leads cold ...

20 – English MAINTENANCE NOTE: Use only HUSQVARNA replacement parts. Use ofother brands of replacement parts can cause damage to yourunit or injury to the operator or others. Your warranty doesnot cover damage or liability caused by the use of accessoriesand/or attachments not specifically recommend...

English – 21 TECHNICAL DATA Technical data Engine Displacement, cu. in/cm 3 Cylinder bore, inch/mmStroke length, inch/mmRecommended max. speed, rpmIdling speed, rpmSpeed of output shaft, rpmMax. engine output, acc. to ISO 8893,kW/rpmCatalytic converter mufflerSpeed-regulated ignition system Ignition...

24 – English EMISSION CONTROL WARRANTY STATEMENT YOUR WARRANTY RIGHTS AND OBLIGATIONS The EPA (The US Environmental Protection Agency),Environment Canada and Husqvarna Forest & Garden arepleased to explain the emissions control system warrantyon your 2001 and later small nonroad engine. In U.S. ...

26 – English 1 Tri Cut 2 3 4 5 6 7 8 >20mm >20mm ! B A 6 Nm X 10

English – 27 1 Trimmy H II 2 3 4 5 6 7 8 9 7,5 m 25' 2,0-2,4 mm .080-.095" 1 2 15 cm 6" ~ 3,7 m 12' 15 cm 6"

28 – English 1 Trimmy Hit 2 3 4 5 6 7 8 9 10 11 “Click” “Click” 7,0 m 23' " 12 cm 5" ~ 3,5 m 11' 15 cm 6 " " 2,0-2,4 mm .080-.095 ~ 15 cm 6

English – 29 1 Trimmy Hit Junior 2 5 6 7 8 9 10 12 “Click” 3 4 5,75 m 19' 2,0-2,4 mm .080-.095" 15 cm 6" ~ 2,8 m 9' 1.) 2.) 11 15 cm 6" 15 cm 6"

30 – English 1 Trimmy Hit Pro 2 5 6 7 8 9 10 12 “Click” 3 4 7,5 m 25' 2,0-2,4 mm .080-.095" 15 cm 6" ~ 3,7 m 12' 1.) 2.) 11 15 cm 6" 15 cm 6"

English – 31 1 Trimmy Hit VI 2 5 6 3 4 7 8 9 10 11 “Click” 7,0 m 23' " 12 cm 5" ~ 3,5 m 11' 15 cm 6 " " 2,0-2,4 mm .080-.095 ~ 15 cm 6

32 – English 1 2 3 4 5 6 7 8 9 35-50 NM ~ 15 cm 6' "Clic" ~ 3,5 m 11' 7,0 m 23' 2,4-3,3 mm .095"-.130" 12 cm 5" Trimmy SII

34 – English 6" 2) 1) ~ 15 cm 6" 7 8 9 10 11 15 cm 1 2 3 4 5 6 7,0 m 23" 2,0- mm , 080-." 12 cm 5" ~ 3,5 m 11" Trimmy VII ´+H)y¶5h¨