Husqvarna 324L, 324LD - Manuals

English – 5 WHA T IS WHA T? What is what? LD X 1 Trimmer head 2 Bevel gear 3 Grease filler cap, bevel gear 4 Cutting attachment guard 5 Shaft 6 Loop handle 7 Stop switch 8 Throttle control 9 Throttle lockout 10 Cylinder cover 11 Starter handle 12 Air purge 13 Fuel tank 14 Choke control 15 Air filter...

6 – English GENERAL SAFETY PRECA UTIONS Impor tant Personal protective equipment HEARING PR OTECTION Wear hearing protection that provides adequate noise reduction. EYE PROTECTION Always wear approved eye protection. If you use a visor then you must also wear approved protective goggles. Approved pr...

English – 7 GENERAL SAFETY PRECA UTIONS Mac hine ′′′′ s safety equipment This section descr ibes the machine ′ s safety equipment, its purpose, and how checks and maintenance should be carried out to ensure that it operates correctly. See the ”What is what?” section to locate where this equipment is...

8 – English GENERAL SAFETY PRECA UTIONS Vibration damping system Your machine is equipped with a vibration damping system that is designed to reduce vibration and make operation easier. Use of incorrectly wound cord or an incorrect cutting attachment increases the level of vibration. See instruction...

English – 9 GENERAL SAFETY PRECAUTIONS Locking nut A locking nut is used to secure some types of cutting attachment. When fitting, tighten the nut in the opposite direction to the direction of rotation of the cutting attachment. To remove it, undo the nut in the same direction as the cutting attachm...

10 – English ASSEMBLY Fitting the loop handle • Clip the loop handle onto the shaft. Note that the loop handle must be fitted between the arrows on the shaft. • Slide the spacer into the slot in the loop handle. • Fit the nut, knob and screw. Do not overtighten. • Now adjust the trimmer to give a co...

12 – English FUEL HANDLING Fuel handling Never start the machine: 1 If you have spilled fuel on it. Wipe off the spillage and allow remaining fuel to evaporate. 2 If you have spilled fuel on yourself or your clothes, change your clothes. Wash any part of your body that has come in contact with fuel....

English – 13 FUEL HANDLING Fueling Clean around the fuel cap. Clean the fuel and oil tank regularly. The fuel filter should be changed at least once a year. Contamination in the tanks causes malfunction. Always move the machine about 3 metres from the refuelling position before starting. ! WARNING! ...

14 – English STARTING AND STOPPING Check before starting • Check that the support flange is not cracked due to fatigue or due to being tightened too much. Discard the support flange if it is cracked. • Ensure the locking nut has not lost its captive force. The nut lock should have a locking force of...

English – 15 STARTING AND STOPPING Warm engine Ignition: Set the stop switch to the start position. Choke: Put the choke in working position. Primer bulb: Press the air purge repeatedly until fuel begins to fill the bulb. The bulb need not be completely filled. Starting Hold the body of the machine ...

16 – English WORKING TECHNIQUES General working instructions Basic safety rules 1 Look around you: • To ensure that people, animals or other things cannot affect your control of the machine. • To ensure that people, animals, etc., do not come into contact with the cutting attachment or loose objects...

English – 17 WORKING TECHNIQUES Grass trimming with a trimmer head Trimming • Hold the trimmer head just above the ground at an angle. It is the end of the cord that does the work. Let the cord work at its own pace. Never press the cord into the area to be cut. • The cord can easily remove grass and...

18 – English MAINTENANCE Carburetor Function • The carburetor governs the engine’s speed via the throttle control. Air and fuel are mixed in the carburetor. • Setting the carburettor involves adapting the engine to suit local conditions, e.g. climate, altitude and the petrol. Basic setting The basic...

English – 19 MAINTENANCE Cooling system To keep the working temperature as low as possible the machine is equipped with a cooling system. The cooling system consists of: 1 Air intake on the starter. 2 Fins on the flywheel. 3 Cooling fins on the cylinder. 4 Cylinder cover (directs cold air over the c...

20 – English MAINTENANCE Oiling the air filter Always use HUSQVARNA filter oil, art. no. 531 00 92-48. The filter oil contains a solvent to make it spread evenly through the filter. You should therefore avoid skin contact. Put the filter in a plastic bag and pour the filter oil over it. Knead the pl...

English – 21 MAINTENANCE Maintenance schedule The following is a list of the maintenance that must be performed on the machine. Most of the items are described in the Maintenance section. The user must only carry out the maintenance and service work described in this manual. More extensive work must...

22 – English TECHNICAL DATA Technical data Note 1: Equivalent noise pressure level is calculated as the time-weighted energy total for noise pressure levels under various working conditions with the following time distribution: 1/2 idle and 1/2 max. speed. NOTE! Noise pressure at the user’s ear and ...

24 – English FEDERAL AND CALIFORNIA EMISSIONS CONTROL WARRANTY STATEMENT YOUR WARRANTY RIGHTS AND OBLIGATIONS The EPA (U.S. Environmental Protection Agency), CARB (California Air Resources Board), Environment Canada and Husqvarna Forest & Garden are pleased to explain the emissions control syste...

English – 25 FEDERAL AND CALIFORNIA EMISSIONS CONTROL WARRANTY STATEMENT ADD -ON OR MODIFIED PARTS Add-on or modified parts that are not exempted by CARB or EPA may not be used. The use of any non-exempted add-on or modified parts will be grounds for disallowing a warranty claim. Husqvarna Forest &a...