Husqvarna 323HD60, 325HD60X-Series, 325HD75X-Series - Manuals

English – 5 WHA T IS WHA T? What is what? 1 Operator ′ s manual 2 Grease fi ller cap, bevel gear 3 Gear housing 4 Blades 5 Blade guard 6 Front handle 7 Cylinder cover 8 Starter handle 9 Stop switch 10 Throttle lock 11 Adjustable handle 12 Throttle control 13 Lock for handle (325HD60, 325HD75) 14 Fue...

6 – English GENERAL SAFETY PRECA UTIONS Impor tant Personal protective equipment HEARING PR OTECTION Wear hearing protection that provides adequate noise reduction. EYE PROTECTION Always wear approved eye protection. If you use a visor then you must also wear approved protective goggles. Approved pr...

English – 7 GENERAL SAFETY PRECA UTIONS Mac hine ′′′′ s safety equipment This section descr ibes the machine ′ s safety equipment, its purpose, and how checks and maintenance should be carried out to ensure that it operates correctly. See the ”What is what?” section to locate where this equipment is...

8 – English GENERAL SAFETY PRECA UTIONS Vibration damping system Your machine is equipped with a vibration damping system that is designed to minimize vibration and make operation easier. The machine ′ s vibration damping system reduces the transfer of vibration between the engine unit/cutting equip...

English – 9 GENERAL SAFETY PRECAUTIONS Blades To ensure good cutting results it is important that the contact pressure between the blades is correct. The contact pressure is adjusted by turning the screws on the underside of the bar clockwise as far as they will go. Then turn the screws anticlockwis...

10 – English FUEL HANDLING Fuel safety Never start the machine: 1 If you have spilt fuel on it. Wipe off the spillage and allow remaining fuel to evaporate. 2 If you have spilt fuel on yourself or your clothes, change your clothes. Wash any part of your body that has come in contact with fuel. Use s...

English – 11 FUEL HANDLING Mixing • Always mix the petrol and oil in a clean container intended for fuel. • Always start by fi lling half the amount of the petrol to be used. Then add the entire amount of oil. Mix (shake) the fuel mixture. Add the remaining amount of petrol. • Mix (shake) the fuel m...

12 – English STARTING AND STOPPING Check before starting • Inspect the working area. Remove any objects that could be thrown out. • Check the cutting attachment. Never use blades that are dull, cracked or damaged. • Check that the machine is in perfect working order. Check that all nuts and screws a...

English – 13 STARTING AND STOPPING Starting Hold the body of the machine on the ground using your left hand (CAUTION! Not with your foot!). Grip the starter handle, slowly pull out the cord with your right hand until you feel some resistance (the starter pawls grip), now quickly and powerfully pull ...

14 – English WORKING TECHNIQUES General working instructions Personal protection • Wear personal protective equipment. See instructions under the heading Personal protective equipment. • Always wear working clothes and heavy-duty long trousers. • Never wear loose clothing or jewellery. • Make sure y...

English – 15 WORKING TECHNIQUES Safety instructions after completing work • The transport guard should always be fi tted to the cutting attachment when the machine is not in use. • Make sure the cutting attachment has stopped before cleaning, carrying out repairs or an inspection. Disconnect the HT ...

16 – English MAINTENANCE Carburettor Your Husqvarna product has been designed and manufactured to speci fi cations that reduce harmful emissions. After the engine has used 8-10 tanks of fuel the engine will be run-in. To ensure that it continues to run at peak performance and to minimise harmful exh...

English – 17 MAINTENANCE Fine adjustment of the idle speed T Adjust the idle speed with the idle adjustment screw T, if adjustment is necessary. First turn the idle adjustment screw T clockwise until the blades start to move. Then turn the idle adjustment screw T anticlockwise until the blades stop....

18 – English MAINTENANCE Cooling system To keep the working temperature as low as possible the machine is equipped with a cooling system. The cooling system consists of: 1 Air intake on the starter. 2 Fins on the fl ywheel. 3 Cooling fi ns on the cylinder. 4 Cylinder cover (directs cold air over the...

English – 19 MAINTENANCE Gear housing There is a grease nipple and a plug for fi lling lubricant on the gear housing. Use a grease gun to fi ll with grease. This should be done after every 60 working hours. Use Husqvarna’s special grease, no. 503 98 96-01. CAUTION! The gear housing must not be fi ll...

20 – English MAINTENANCE Maintenance schedule The following is a list of the maintenance that must be performed on the machine. Most of the items are described in the Maintenance section. The user must only carry out the maintenance and service work described in this Operator’s Manual. More extensiv...

English – 21 TECHNICAL DATA Technical data Note 1: Noise emissions in the environment measured as sound power (L WA ) in conformity with EC directive 2000/14/EC. Note 2: Equivalent sound pressure level is calculated as the time-weighted energy total for sound pressure levels under various working co...