Husqvarna 235R - Manuals

English – 5 WHA T IS WHA T? What is what? 28 27 1 Blade 2 Grease fi ller cap, bevel gear 3 Bevel gear 4 Cutting attachment guard 5 Shaft 6 Handlebar 7 Throttle control 8 Stop switch 9 Throttle lock 10 Support eyes for harness 11 Cylinder cover 12 Starter handle 13 Fuel tank 14 Choke control 15 Air p...

6 – English GENERAL SAFETY PRECA UTIONS Impor tant Personal protective equipment HELMET A helmet should be w orn if the trees being cleared are taller than 2 m. HEARING PROTECTION Wear hearing protection that provides adequate noise reduction. EYE PROTECTION Always wear approved eye protection. If y...

English – 7 GENERAL SAFETY PRECA UTIONS Mac hine ′′′′ s safety equipment This section descr ibes the machine ′ s safety equipment, its purpose, and how checks and maintenance should be carried out to ensure that it operates correctly. See the ”What is what?” section to locate where this equipment is...

English – 9 GENERAL SAFETY PRECAUTIONS Never use a machine that has a faulty muf fl er. Regularly check that the muf fl er is securely attached to the machine. If the muf fl er on your machine is fi tted with a spark arrestor mesh this must be cleaned regularly. A blocked mesh will cause the engine ...

10 – English GENERAL SAFETY PRECAUTIONS Cutting equipment Saw blades are intended for cutting fi brous types of wood. Grass blades and grass cutters are intended for cutting coarse grass. A trimmer head is intended for trimming grass. General rules Only use cutting attachments with the guards we rec...

English – 11 GENERAL SAFETY PRECAUTIONS so, this should be done before fi ling with a round fi le. The top edges must be fi led down by the same amount for all the teeth. Adjust the blade setting. This should be 1 mm. Trimmer head • Only use the recommended trimmer heads and trimmer cords. These hav...

12 – English ASSEMBLY Fitting the handlebar (232R) • Remove the screw at the rear of the throttle handle. • Slide the throttle handle onto the right side of the handlebar, (see diagram). • Align the screw hole in the throttle handle with the hole in the handlebar. • Re fi t the screw in the hole in ...

English – 13 ASSEMBLY Transport position, handlebar • The handlebar can easily be turned to fi t along the shaft for easier transportation and storage. • Loosen the knob. Turn the handlebar clockwise so that the throttle handle rests against the engine. • Now twist the handlebar around the shaft. Ti...

English – 17 ASSEMBLY Fitting other guards and cutting attachments (235R) • Fit the trimmer guard/combination guard (A) intended for use with the trimmer head/plastic blades. CAUTION! Ensure that the guard extension is fi tted. Hang the trimmer guard/combination guard (A) on the two hooks on the pla...

18 – English FUEL HANDLING Fuel safety Never start the machine: 1 If you have spilt fuel on it. Wipe off the spillage and allow remaining fuel to evaporate. 2 If you have spilt fuel on yourself or your clothes, change your clothes. Wash any part of your body that has come in contact with fuel. Use s...

English – 19 FUEL HANDLING Mixing • Always mix the gasoline and oil in a clean container intended for fuel. • Always start by fi lling half the amount of the gasoline to be used. Then add the entire amount of oil. Mix (shake) the fuel mixture. Add the remaining amount of gasoline. • Mix (shake) the ...

20 – English STARTING AND STOPPING Check before starting • Check the blade to ensure that no cracks have formed at the bottom of the teeth or by the centre hole. The most common reason why cracks are formed is that sharp corners have been formed at the bottom of the teeth while sharpening or that th...

English – 21 STARTING AND STOPPING Warm engine Ignition: Set the stop switch to the start position. Choke: Set the throttle to the start position by moving the choke control to the choke position and then returning it to its original position. Primer bulb: Press the air purge repeatedly until fuel b...

22 – English WORKING TECHNIQUES General working instructions Basic safety rules 1 Look around you: • To ensure that people, animals or other things cannot affect your control of the machine. • To ensure that people, animals, etc., do not come into contact with the cutting attachment or loose objects...

English – 23 WORKING TECHNIQUES Working methods • Before you start clearing, check the clearing area, the type of terrain, the slope of the ground, whether there are stones, hollows etc. • Start at whichever end of the area is easiest, and clear an open space from which to work. • Work systematicall...

24 – English WORKING TECHNIQUES • Large stems must be cut from two sides. First determine which direction the stem will fall. Make the fi rst cut on the felling side. Then fi nish cutting the stem from the other side. Adjust the cutting pressure to match the size of the stem and the hardness of the ...

26 – English MAINTENANCE Carburetor Your Husqvarna product has been designed and manufactured to speci fi cations that reduce harmful emissions. After the engine has used 8-10 tanks of fuel the engine will be run-in. To ensure that it continues to run at peak performance and to minimise harmful exha...

English – 27 MAINTENANCE will run smoothly in every position. The idle speed should also be well below the speed at which the cutting attachment starts to rotate. High speed jet H The high speed jet H affects the engine power, speed, temperature and fuel consumption. If the high speed jet H is set t...

28 – English MAINTENANCE Cooling system To keep the working temperature as low as possible the machine is equipped with a cooling system. The cooling system consists of: 1 Air intake on the starter. 2 Fins on the fl ywheel. 3 Cooling fi ns on the cylinder. 4 Cylinder cover (directs cold air over the...

English – 29 MAINTENANCE Spark plug The spark plug condition is in fl uenced by: • Incorrect carburetor adjustment. • An incorrect fuel mixture (too much or incorrect type of oil). • A dirty air fi lter. These factors cause deposits on the spark plug electrodes, which may result in operating problem...

30 – English MAINTENANCE Maintenance schedule The following is a list of the maintenance that must be performed on the machine. Most of the items are described in the Maintenance section. The user must only carry out the maintenance and service work described in this manual. More extensive work must...

English – 31 TECHNICAL DATA Technical data Note 1: Equivalent noise pressure level is calculated as the time-weighted energy total for noise pressure levels under various working conditions with the following time distribution: 1/2 idle and 1/2 max. speed. NOTE! Noise pressure at the user’s ear and ...

English – 33 FEDERAL EMISSION CONTROL WARRANTY STATEMENT YOUR WARRANTY RIGHTS AND OBLIGATIONS The EPA (The US Environmental Protection Agency), Environment Canada and Husqvarna Forest & Garden are pleased to explain the emissions control system warranty on your 2001 and later small nonroad engin...

1 Trimmy Hit 2 3 4 5 6 7 8 9 10 11 “Click” “Click” 7,0 m 23' " 12 cm 5" ~ 3,5 m 11' 15 cm 6 " " 2,0-2,4 mm .080-.095 ~ 15 cm 6

1 Trimmy Hit Pro 2 5 6 7 8 9 10 12 “Click” 3 4 7,5 m 25' 2,0-2,4 mm .080-.095" 15 cm 6" ~ 3,7 m 12' 1.) 2.) 11 15 cm 6" 15 cm 6"

1 2 3 4 5 6 7 8 9 35-50 NM ~ 15 cm 6' "Clic" ~ 3,5 m 11' 7,0 m 23' 2,4-3,3 mm .095"-.130" 12 cm 5" Trimmy SII