Husqvarna 2.010 BP - Manuals

Page 3 - EE

40-43-46-49cc 52cc E5 E6 52 cc 40-43-46-49 cc H H F1 G I1 H1 H3 H4 I2 I3 L SUMMARY CHART TO IDENTIFY THE CORRECTGUARD NEEDED, WITH DIFFERENT CUTTINGATTACHMENTS ÜBERSICHTSTABELLE ZUR AUSWAHL DES RICHTI-GEN SCHUTZBLECHES FÜR DIE EINZELNENSCHNEIDWERKZEUGE TABLEAU RECAPITULATIF POUR LE CORRECTACCOUPLEME...

Page 4 - Explanation of Symbols; TRIGGER; B . S a f e t y p r e c a u t i o n s; ) Guaranteed noise level according to; Example of identification label

ENGLISH - 1 Warning Safety apparel: Approved protectivegoggles or visor, approved hard hatand hearing protection. Read the instructions for the usercarefully and make sure you under-stand how all the controls work. Safety apparel: Approved gloves. Safety apparel: Approved boots. Do not smoke when re...

Page 5 - Starting and stopping the engine

2 - ENGLISH Use of the manual • Anyone who uses the machine should have read the entire manual with extreme care. • All users should be familiar with the operations for use of the machine under absolutely safe conditions as described in this manual, and should be instructed in the proper cutting tec...

Page 6 - Apparel; • Closely fitting protective clothing (do not wear; Health precautions; Syndrome of Raynaud; Work zone

ENGLISH - 3 • possible contact with flying debris.Never use a brush cutter without its safety pole guard correctly in place. Only use blades or nylon string heads clearly marked with a maximum speed of at least 10,500 min -1 . Use only original or approved accessories and spare parts, which you can ...

Page 7 - Precautions for carrying the machine; Protection for transport; Fire prevention precautions; in the risk sector to prevent kickback.; Safety lever; automatically to their original positions.; C. Description of the safety devices on the machine

4 - ENGLISH obstacles. Use the machine holding it to the right of your body so that the exhaust fumes can escape freely without obstruction from your clothing. While working, grip the brush cutter firmly with both hands. Stand in a stable position on your feet. Keep the grips clean and dry. Do not u...

Page 9 - E . M o n t a g g i o / s m o n t a g g i o

E1. Setting the motor on the frame Position the motor so that the fuel cap facesupward and the bracket for fastening it to theframe is on one side. Screw pin A onto the motoras shown in the figure and tighten it securely.Fasten the motor to the frame and tighten itsecurely with the nut provided (B)....

Page 10 - Assembly of sawtooth blade and blade guard; ) with the sawtooth blade; F. Starting and stopping the engine; The cutting devices are now rotating.; G. Carburetor adjustment

ENGLISH - 7 Lower washer - e) Spacer - f) Rotating mower gauge - g) Blade locking screw (length mm 34,5). Assembly of sawtooth blade and blade guard  For assembly see figures ( E7, E8, E9 ).  Startup of cold engineF1. Stop switch ( A ) turned to “I” opposite the “STOP” mark. F2. Turn the fuel enri...

Page 11 - H. Routine maintenance

8 - ENGLISH  After every use In order to avoid overheating the motor, remove any dust and dirt from the slots on the cylinder cover and finds of the cylinder using a wooden scraper. Clean the backpack (if you wish, you can wash the padding after removing it from the frame). Store the machine in a d...

Page 12 - KICKBACK can occur when cutting is done; L. Environmental information; Make sure the STOP switch is on “I”.

ENGLISH - 9 Drawing out the string During cutting, the nylon string wears naturally causing an increase in the speed of the engine and a reduced cutting capacity. When this happens, to bring out more string bump the head against the ground: release the throttle trigger to reduce the engine speed to ...

Page 13 - starting from the serial numbers produced from 2006 on, manufac-; Maximum shaft rotation frequency (min; Measured sound power level Lw; Guaranteed noise level Lw

10 - ENGLISH O . Te c h n i c a l d a t a N . D e c l a r a t i o n o f c o n f o r m i t y The undersigned, authorized by Husqvarna Outdoor Products Italia SpA, declares that the following prod-ucts model /TYPE: BC011, BC012 starting from the serial numbers produced from 2006 on, manufac- tured by ...