Husqvarna 170BT - Manuals - manualsarea.com

Page 2 - EC-declaration of conformity

English 2 EC-declaration of conformity (Applies to Europe only) Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel +46-36-146500, declares under sole responsibility that the blowers Husqvarna 170BT with serial numbers dating 2006 and onwards (the year is clearly stated on the rating plate, followed by t...

Page 3 - Contents

English 3 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 SAFETY FIRST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Notes on types of war...

Page 4 - SAFETY FIRST; Notes on types of warnings; Symbols; Warning labels on the machine

English 4 SAFETY FIRST Instructions contained in warnings within this manual and warning seals marked with a symbol on the blower concern critical points which must be taken into consideration to prevent possible serious bodily injury, and for this reason you are requested to read all such instructi...

Page 5 - Safety Precautions

English 5 For safe operation and maintenance, symbols are carved in relief on the machine. Using to these indications, please be careful not to make a mistake. (a) The port to refuel the "MIX GASOLINE" Position: FUEL TANK CAP (b) The direction to close the choke Position: INTAKE CUP (c) The ...

Page 7 - USING THE PRODUCT; MAINTENANCE; TRANSPORTATION

English 7 WARNING Check to see if the shock-absorbing rubber mount has become cracked or otherwise damaged. Note that failing to replace this rubber mount when it has become cracked or damaged may cause the engine to come loose from its frame during use, thus resulting in possible serious bodily inj...

Page 8 - DISPOSAL

English 8 1. Frame2. Shoulder Strap3. Spark Plug Cap4. Throttle Lever5. Net6. Choke Lever7. Air Cleaner8. Volute Case 9. “CAUTION” Label10.Elbow11. Fuel Tank12.Recoil Starter13.Ignition Switch14.Engine Cover15.Handle Bar (Accessory)16.Fan 16 7 3 8 11 15 1 2 5 6 12 14 10 13 4 9 DISPOSAL When dispos...

Page 9 - Technical data

English 9 * The data shown above are those in the case of one straight pipe. * Specifications are subject to change without notice. MODEL 170BT Dimensions (L x W x H) mm (in) 365x464x485 (14x18x19) Dry Weight kg (lbs) (including pipe) 12 (26.5) (total weight) Fuel Tank Capacity liter (fl. oz) 1.75 (...

Page 10 - SWIVEL JOINT; THROTTLE LEVER; Assembly

English 10 SWIVEL JOINT 1. Connect the blower and swivel joint with flexible hose. Clamp both ends of the flexible hose securely with the hardware supplied with the unit. THROTTLE LEVER 1. Set up the throttle holder to the swivel and tighten the screw on the holder. When setting up the holder, p...

Page 11 - HARNESS; WAIST BELT

English 11 HARNESS NOTE The harness must always be worn when working with the machine. Failure to do so means you will be unable to maneuver safely and this can result in injury to yourself or others. A correctly adjusted harness and machine significantly facilitates the work. Adjust the harness t...

Page 12 - FUEL; HOW TO MIX FUEL; FUELING THE UNIT; Fuel

English 12 FUEL WARNING • Gasoline is very flammable. Avoid smoking or bringing any flame or sparks near fuel. Make sure to stop the engine and allow it cool before refueling the unit. Select outdoor bare ground for fueling and move at least 10ft (3m) away from the fueling point before starting th...

Page 13 - STARTING ENGINE; ADJUSTING IDLE SPEED; STOPPING ENGINE; Operation

English 13 STARTING ENGINE IMPORTANT • Avoid operating the blower with the flexible tube and swivel joint disconnected. That will reduce the cooling air and the engine could be damaged by overheating. 1. Push the primer bulb until fuel flows out in the clear tube. (F12)2. When the engine is cool, ...

Page 14 - AIR CLEANER; FUEL FILTER; Maintenance

English 14 Maintenance, replacement, or repair of the emission control device and systems may be performed by any non-road engine repair establishment or individual. WARNING Make sure that the engine has stopped and is cool before performing any service to the blower. Contact with rotating blower fa...

Page 15 - SPARK PLUG; MUFFLER; SPARK ARRESTER; AIR INLET NET

English 15 SPARK PLUG • The spark plug may gather carbon deposits on its firing end with reasonable use. Remove and inspect the spark plug every 25 hours and clean the electrodes as necessary with a wire brush. The spark gap should be adjusted to .025 in (0.6 to 0.7mm). • Plug manufacturers recomm...

Page 16 - IGNITION COIL AIR GAP INSPECTION; SHOLDER STRAP; Storage

English 16 IGNITION COIL AIR GAP INSPECTION • If the gap is not accurate or when installing the coil or rotor, adjust the air gap between the ignition coil and the iron core of the rotor. Air Gap: 0.40mm (0.35 to 0.45mm)0.016 in (0.014 to 0.017 in) (1) Rotor(2) Ignition coil SHOLDER STRAP • If t...