Husqvarna 123C - Manuals

English – 5 SAFETY INSTRUCTIONS Vibration damping system Your machine is equipped with a vibration damping system that is designed to minimize vibration and make operation easier. Use of incorrectly wound cord or an incorrect cutting attachment increases the level of vibration. Muffler The muffler i...

6 – English SAFETY INSTRUCTIONS Checking, maintaining and servicing the machine ′′′′ s safety equipment Throttle lock • Make sure the throttle control is locked at the idle setting when the throttle lock is released. • Press the throttle lock and make sure it returns to its original position when yo...

English – 7 SAFETY INSTRUCTIONS Cutting equipment This section describes how to choose and maintain your cutting equipment in order to: • Obtain maximum cutting performance. • Extend the life of cutting equipment. General rules 1 Only use cutting attachments with the guards we recommend! See the cha...

8 – English SAFETY INSTRUCTIONS General safety precautions Starting • The complete clutch cover and shaft must be fitted before the machine is started, otherwise the clutch can come loose and cause personal injury. • Never start the machine indoors. Exhaust fumes can be dangerous if inhaled. • Obser...

English – 9 SAFETY INSTRUCTIONS • The transport guard must always be fitted to the cutting attachment when the machine is being transported or in storage. General working instructions Basic safety rules 1 Look around you: • To ensure that people, animals or other things cannot affect your control of...

English – 11 WHAT IS WHAT? What is what? C LD 1 Trimmer head 2 Grease filler cap 3 Bevel gear 4 Cutting attachment guard 5 Shaft 6 Loop handle 7 Throttle control 8 Stop switch 9 Throttle lock 10 Cylinder cover 11 Starter handle 12 Fuel tank 13 Choke control 14 Air purge 15 Air filter cover 16 Handle...

12 – English ASSEMBLY Fitting the loop handle • Position the handle on the shaft. Note that the handle must be mounted below the arrow on the shaft. • Fit the screw, securing plate and wing nut as shown in the diagram. • Tighten the wing nut. Assembling and dismantling the two-piece shaft (123LD) As...

English – 13 ASSEMBLY Fitting the trimmer guard and trimmer head (123C) Guard • Fit the guard as shown in the diagram. Tighten securely. Trimmer head • Fit the dust cup on the shaft. The nut must be completely covered by the dust cup. • Hold the dust cup with a spanner to prevent the shaft from rota...

14 – English FUEL HANDLING Fuel CAUTION! The machine is equipped with a two-stroke engine and must always been run using a mixture of gasoline and two-stroke engine oil. It is important to accurately measure the amount of oil to be mixed to ensure that the correct mixture is obtained. When mixing sm...

English – 15 FUEL HANDLING Fuelling • Clean the area around the fuel cap. Contamination in the tank can cause operating problems. • Ensure that the fuel is well mixed by shaking the container before filling the tank. ! WARNING! Taking the following precautions, will lessen the risk of fire: Do not s...

16 – English STARTING AND STOPPING Check before starting • Check that the support flange is not cracked due to fatigue or due to being tightened too much. Discard the support flange if it is cracked. • Ensure the locking nut has not lost its captive force. The nut lock should have a locking force of...

English – 17 STARTING AND STOPPING Warm engine Ignition: Set the stop switch to the start position. Choke: Set the throttle to the start position by moving the choke control to the choke position and then returning it to its original position. Air purge: Press the air purge diaphragm repeatedly unti...

18 – English MAINTENANCE Carburettor Your Husqvarna product has been designed and manufactured to specifications that reduce harmful emissions. After the engine has used 8-10 tanks of fuel the engine will be run-in. To ensure that it continues to run at peak performance and to minimise harmful exhau...

English – 19 MAINTENANCE Fine adjustment of the idle speed T Adjust the idle speed using the idle adjustment screw T, if it is necessary to readjust. First turn the idle adjustment screw T clockwise until the cutting attachment starts to rotate. Then turn the screw anticlockwise until the cutting at...

20 – English MAINTENANCE Cooling system To keep the working temperature as low as possible the machine is equipped with a cooling system. The cooling system consists of: 1 Air intake on the starter. 2 Fins on the flywheel. 3 Cooling fins on the cylinder. 4 Cylinder cover (directs cold air over the c...

English – 21 MAINTENANCE Put the filter in a plastic bag and pour the filter oil over it. Knead the plastic bag to distribute the oil. Squeeze the excess oil out of the filter inside the plastic bag and pour off the excess before fitting the filter to the machine. Never use common engine oil. This w...

22 – English TECHNICAL DATA Technical data Note 1: Equivalent noise pressure level is calculated as the time-weighted energy total for noise pressure levels under various working conditions with the following time distribution: 1/2 idle and 1/2 max. speed. NOTE! Noise pressure at the user’s ear and ...

24 – English FEDERAL EMISSION CONTROL WARRANTY STATEMENT YOUR WARRANTY RIGHTS AND OBLIGATIONS The EPA (The US Environmental Protection Agency), Environment Canada and Husqvarna Forest & Garden are pleased to explain the emissions control system warranty on your 2001 and later small nonroad engin...

´®z+H6G¶5I¨ ´®z+H6G¶5I¨ 6" 2) 1) ~ 15 cm 6" 7 8 9 10 11 15 cm 1 2 3 4 5 6 7,0 m 23" 2,0- mm , 080-." 12 cm 5" ~ 3,5 m 11" Trimmy VII