Husqvarna 1153191-26 - Manuals

SAFETY INSTR UCTIONS English – 5 P ersonal protective equipment • Gloves should be worn when necessary. • Wear hearing protection that provides adequate noise reduction. • Always wear approved eye protection. If you use a visor then you must also wear approved protective goggles. Approved protective...

SAFETY INSTR UCTIONS 6 – English Vibration damping system Y our machine is equipped with a vibration damping system that is designed to minimize vibration and make operation easier. Muffl er The m uffler is designed to keep noise levels to a minimum and to direct exhaust fumes away from the user. In...

SAFETY INSTR UCTIONS English – 7 Vibration damping system • Check the vibration damping units regularly for cracks or deformation. Replace them if damaged. • Check that the vibration damping element is undamaged and securely attached. Muffl er • Never use a machine that has a faulty muffler. • Regul...

SAFETY INSTRUCTIONS 8 – English Starting • Never start the machine indoors. Exhaust fumes can be dangerous if inhaled. • Observe the surroundings and ensure that no people or animals can come into contact with the blower. • Place the machine on the ground, press the machine body against the ground w...

SAFETY INSTRUCTIONS English – 9 Place the hip strap over the hip and not too far down on the stomach. Tighten the hip strap so that you feel the weight of the blower resting on your hip. General working instructions Show consideration to persons in your surroundings by avoiding using the machine at ...

SAFETY INSTRUCTIONS 10 – English Basic working techniques • The speed of the air jet is regulated by means of the throttle. Select the speed best suited for respective tasks. You can set the throttle position using the ”stop switch” and by doing so not need to hold your finger on the throttle all th...

ASSEMBLY 12 – English Assembling the blow pipe and control handle • Loosen the two screws on the fan’s outlet pipe and remove the two wear ring halves located on the outlet pipe. • Place these on the pipe bend so that the guide on the wear ring halves aligns with the slot on the pipe bend. • Refit t...

ASSEMBLY English – 13 Accessories Handlebar Disassemble the intermediate pipe. Disassemble the knob from the holder and puch the holder on to the holder pipe. Assemble the knob and tighten. Assemble the intermediate pipe. Flat nozzle • If higher air speed is required, the round blow pipe is replaced...

FUEL HANDLING 14 – English Fuel CAUTION! The machine is equipped with a two-stroke engine and must always been run using a mixture of petrol and two-stroke oil. It is important to accurately measure the amount of oil to be mixed to ensure that the correct mixture is obtained. When mixing small amoun...

FUEL HANDLING English – 15 Fuelling • Move the machine at least 3 m from the refuelling point before starting it. • Clean the area around the fuel cap. Contamination in the tank can cause operating problems. • Ensure that the fuel is well mixed by shaking the container before filling the tank. ! WAR...

STARTING AND STOPPING 16 – English Starting and stopping Cold engine Ignition: Set the stop switch to the start position. Start position is achieved by moving the stop switch slightly backwards until the stop switch clicks into start position. It is not allowed to set the stop switch in full throttl...

MAINTENANCE English – 17 Carburettor Your Husqvarna product has been designed and manufactured to specifications that reduce harmful emissions. After the engine has used 8-10 tanks of fuel the engine will be run-in. To ensure that it continues to run at peak performance and to minimise harmful exhau...

MAINTENANCE 18 – English Loosen the muffler’s 2 screws and remove the muffler. Pull out the spark arrestor mesh and clean using a wire brush. Replace the spark arrestor mesh if it is defective. CAUTION! Never use a machine with a defective muffler. Cooling system To keep the working temperature as l...

MAINTENANCE English – 19 Clean the filter every 40 hours, or more regularly if conditions are exceptionally dusty. Avoid contact with hot surfaces on muffler, cylinder etc. Contact can result in burns to the skin. Cleaning the air filter Dismantle the outer cover with the help of the four fasteners ...

MAINTENANCE 20 – English Maintenance schedule Below you will find some general maintenance instructions. If you need further information please contact your service workshop. Daily maintenance 1 Clean the outside of the machine. 2 Check that the throttle control functions safely. 3 Check that the st...

English – 21 TECHNICAL DATA Technical data Note 1: Noise emissions in the environment measured as sound power (L WA ) in conformity with EC directive 2000/14/ EC. Reported sound power level for the machine has been measured with the original cutting attachment that gives the highest level. The diffe...

Original instructions ´®z+U3,¶6;¨ ´®z+U3,¶6;¨ 2010-05-18 1153191-26