Husqvarna 1151187-95 - Manuals

GENERAL SAFETY PRECA UTIONS 6 – English Impor tant Personal protective equipment HELMET A helmet should be w orn if the trees being cleared are taller than 2 m. HEARING PROTECTION Wear hearing protection that provides adequate noise reduction. EYE PROTECTION Always wear approved eye protection. If y...

GENERAL SAFETY PRECA UTIONS English – 7 BOO TS Wear boots with steel toe-caps and non-slip sole. CLOTHING Wear clothes made of a strong fabric and avoid loose clothing that can catch on twigs and branches. Always wear heavy, long pants. Do not wear jewellery, shorts sandals or go barefoot. Secure ha...

GENERAL SAFETY PRECAUTIONS English – 9 saw. Certain harnesses also have a quick release fitted to the support hook. Check that the harness straps are correctly positioned. Once the harness and machine have been adjusted, check that the harness quick release works correctly. Muffler The muffler is de...

GENERAL SAFETY PRECAUTIONS 10 – English should operate the socket spanner when loosening or tightening the nut. The nylon lining inside the locking nut must not be so worn that you can turn it by hand. The lining should offer a resistance of at least 1.5 Nm. The nut should be replaced after it has b...

GENERAL SAFETY PRECAUTIONS English – 11 Check the cutting attachment for damage or cracks. A damaged cutting attachment should always be replaced. Sharpening grass cutters and grass blades • See the cutting attachment packaging for correct sharpening instructions. Sharpen blades and cutters using a ...

GENERAL SAFETY PRECAUTIONS 12 – English Trimmer head • Only use the recommended trimmer heads and trimmer cords. These have been tested by the manufacturer to suit a particular engine size. This is especially important when a fully automatic trimmer head is used. Only use the recommended cutting att...

ASSEMBLY English – 13 Fitting the handlebar (232R) • Remove the screw at the rear of the throttle handle. • Slide the throttle handle onto the right side of the handlebar, (see diagram). • Align the screw hole in the throttle handle with the hole in the handlebar. • Refit the screw in the hole in th...

ASSEMBLY 14 – English • Fit the wiring as shown. • Put on the harness and hang the machine from the support hook. Now make a final adjustment so that the machine is in a comfortable working position when it hangs from the harness. Tighten the knob. Transport position, handlebar • The handlebar can e...

ASSEMBLY English – 19 Place the locking pin in the groove on the screw head and tighten. See diagram. • Fit the drive disc (B) on the output shaft. • Turn the blade shaft until one of the holes in the drive disc aligns with the corresponding hole in the gear housing. • Insert the locking pin (C) in ...

FUEL HANDLING 20 – English Fuel safety Never start the machine: 1 If you have spilled fuel on it. Wipe off the spillage and allow remaining fuel to evaporate. 2 If you have spilled fuel on yourself or your clothes, change your clothes. Wash any part of your body that has come in contact with fuel. U...

FUEL HANDLING English – 21 Mixing • Always mix the gasoline and oil in a clean container intended for fuel. • Always start by filling half the amount of the gasoline to be used. Then add the entire amount of oil. Mix (shake) the fuel mixture. Add the remaining amount of gasoline. • Mix (shake) the f...

STARTING AND STOPPING 22 – English Check before starting • Check the blade to ensure that no cracks have formed at the bottom of the teeth or by the centre hole. The most common reason why cracks are formed is that sharp corners have been formed at the bottom of the teeth while sharpening or that th...

STARTING AND STOPPING English – 23 Primer bulb: Press the air purge repeatedly until fuel begins to fill the bulb. The bulb need not be completely filled. Warm engine Ignition: Set the stop switch to the start position. Choke: Set the throttle to the start position by moving the choke control to the...

WORKING TECHNIQUES 24 – English General working instructions Basic safety rules 1 Look around you: • To ensure that people, animals or other things cannot affect your control of the machine. • To ensure that people, animals, etc., do not come into contact with the cutting attachment or loose objects...

WORKING TECHNIQUES English – 25 The ABC of clearing • Always use the correct equipment. • Make sure the equipment is well adjusted. • Follow the safety precautions. • Organise your work carefully. • Always use full throttle when starting to cut with the blade. • Always use sharp blades. • Avoid ston...

WORKING TECHNIQUES 26 – English conditions, so that cleared stems fall in the cleared area of the stand. Forestry clearing using a saw blade • The risk of blade thrust increases with increasing stem size. You should therefore avoid cutting with the area of the blade between 12 o’clock and 3 o’clock....

WORKING TECHNIQUES English – 27 Brush cutting with a saw blade • Thin stems and brush are mown down. Work with a sawing movement, swinging sideways. • Try to cut several stems in a single sawing movement. • With groups of hardwood stems, first clear around the group. Start by cutting the stems high ...

MAINTENANCE English – 29 Carburetor Your Husqvarna product has been designed and manufactured to specifications that reduce harmful emissions. After the engine has used 8-10 tanks of fuel the engine will be run-in. To ensure that it continues to run at peak performance and to minimise harmful exhaus...

MAINTENANCE 30 – English Low speed jet L Try to find the highest idling speed, turning the low speed needle L clockwise respectively counter-clockwise. When the highest speed has been found, turn the low speed needle L 1/4 turn counter-clockwise. CAUTION! If the cutting attachment rotates when the e...

MAINTENANCE English – 31 Adjusting the start throttle speed The correct start throttle speed is set by means of an adjuster on the rear of the handle next to the cable. Use this screw (4 mm Allen screw) to increase or decrease the start throttle speed. Proceed as follows: 1 Run the machine at idle. ...

MAINTENANCE 32 – English 4 Cylinder cover (directs cold air over the cylinder). Clean the cooling system with a brush once a week, more often in demanding conditions. A dirty or blocked cooling system results in the machine overheating which causes damage to the piston and cylinder. Bevel gear The b...

English – 33 MAINTENANCE Maintenance schedule The following is a list of the maintenance that must be performed on the machine. Most of the items are described in the Maintenance section. The user must only carry out the maintenance and service work described in this manual. More extensive work must...

34 – English TECHNICAL DATA Technical data Note 1: Equivalent noise pressure level is calculated as the time-weighted energy total for noise pressure levels under various working conditions with the following time distribution: 1/2 idle and 1/2 max. speed. NOTE! Noise pressure at the user’s ear and ...

FEDERAL EMISSION CONTROL WARRANTY STATEMENT 36 – English YOUR WARRANTY RIGHTS AND OBLIGATIONS The EPA (The US Environmental Protection Agency), Environment Canada and Husqvarna Forest & Garden are pleased to explain the emissions control system warranty on your 2001 and later small nonroad engin...

FEDERAL EMISSION CONTROL WARRANTY STATEMENT English – 37 MAINTENANCE, REPLACEMENT AND REPAIR OF EMISSION-RELATED PARTS Any Husqvarna Forest & Garden approved replacement part used in the performance of any warranty maintenance or repairs on emission-related parts, will be provided without charge...

1 Trimmy Hit 2 3 4 5 6 7 8 9 10 11 “Click” “Click” 7,0 m 23' " 12 cm 5" ~ 3,5 m 11' 15 cm 6 " " 2,0-2,4 mm .080-.095 ~ 15 cm 6

1 Trimmy Hit Pro 2 5 6 7 8 9 10 12 “Click” 3 4 7,5 m 25' 2,0-2,4 mm .080-.095" 15 cm 6" ~ 3,7 m 12' 1.) 2.) 11 15 cm 6" 15 cm 6"

1 2 3 4 5 6 7 8 9 35-50 NM ~ 15 cm 6' "Clic" ~ 3,5 m 11' 7,0 m 23' 2,4-3,3 mm .095"-.130" 12 cm 5" Trimmy SII