Crimestopper RS-999TW1/TW2 - Manuals

Crimestopper RS-999TW1/TW2 – Manual in PDF format online.

Manuals:

Manual

Manual Crimestopper RS-999TW1/TW2

Summary

Page 2 - BEFORE BEGINNING; may include extra relays or Anti-Theft System Bypass modules.

TABLE OF CONTENTS Pre-Installation Considerations……….………...……...……………………………………………………………….……2 Cautions & Warnings…….…………...….……..…..……………………………………………………………….…..……3 Wiring……..…………………………....……………………………………………………………………………….…….3-7 Wiring High-Current Connector…….………………...…………………………………………………………………........

Page 3 - INSTALLATION CAUTIONS & WARNINGS; result in damage to the unit not covered under warranty.; DO NOT; WIRING

INSTALLATION CAUTIONS & WARNINGS **FOR SAFETY REASONS, DO NOT INSTALL in vehicles with MANUAL TRANSMISSIONS .** If accidentally left in gear, a remote started vehicle could become a self-propelled threat to life and property. DO NOT extend the Remote start ignition harness length. Mount the modu...

Page 5 - BROWN; Connect to+12V for Positive circuits

WIRING PIN 4: BROWN: (-) AUX OUTPUT (TRUNK POP) or DOME LIGHT ILLUMINATION OUTPUT This output is programmable for two modes of operation. See Programming Option Section. Mode (1) DEFAULT: Provides a Ground pulse when button #3 (Trunk) on the remote transmitter is pushed to activate a factory electri...

Page 8 - SEE DIAGRAM on NEXT PAGE

WIRING: 7-PIN HIGH-CURRENT CONNECTOR BROWN: +12V STARTER OUTPUT 30A: Connect to circuit in the vehicle that has power ONLY while the STARTER MOTOR is CRANKING. GRAY: +12V ACCESSORY OUTPUT 30A: Connect to circuit in the vehicle that provides Accessory Power for systems such as HEAT and A/C. Typically...

Page 9 - IGN; OR; ACC

WIRING: 7-PIN HIGH-CURRENT CONNECTOR FUSE RED PINK/WHITE 30A FUSE RED 30A + - BROWN PINK FUEL ENGINE BATTERY PUMP ECU GRAY + STARTER - COIL IGN OR ACC H/V/AC Diagram not to scale, for illustration purposes only. Your vehicle may differ. IGN 2 ACC 2 TOP WHITE START 2 FUSE PARKING LIGHTS IF NECESSARY ...

Page 10 - POWER DOOR LOCK WIRING CONNECTOR; Plug-in pulse inverter that converts the; DETERMINING DOOR LOCK TYPE:

POWER DOOR LOCK WIRING CONNECTOR PIN 1: BLUE: (-) Negative pulse for UNLOCK Crimestopper Door Lock Accessories: CS-6600DLM: Dual-relay plug-in module for Reverse Polarity, Positive, or Aftermarket Motors. CS-6500DLI: Plug-in pulse inverter that converts the Negative outputs of the system to Positive...

Page 11 - BASIC DOOR LOCK DIAGRAMS; NEGATIVE TRIGGER DOORLOCK WIRING

BASIC DOOR LOCK DIAGRAMS AFTERMARKET MOTOR/DOOR LOCK WIRING REVERSE POLARITY DOOR LOCK WIRING GREEN GREEN FUSED FUSED RED RED +12V +12V BLUE BLUE + + 86 85 86 85 86 85 86 85 87 87 87 87 30 87A 30 87A 30 87A 30 87A + L CUT UL CUT MASTER SWITCH NEGATIVE TRIGGER DOORLOCK WIRING POSITIVE TRIGGER DOORLOC...

Page 12 - “SMART TACHLESS” MODE; “SMART TACHLESS” ADJUSTMENT:

“SMART TACHLESS” MODE Your CoolStart system includes a unique voltage monitor called “Smart Tachless” mode. This mode allows this unit to efficiently start an engine without the use of a tach signal wire. These modules actively monitor the voltage level of the vehicle to control the starter motor ea...

Page 13 - TACH FINDER & USEFUL TIPS; TACH FINDER TIP: Erratic vs. Consistent light flashing; range of the system.

TACH FINDER & USEFUL TIPS TACH FINDER MODE: This Tach Finder mode can assist in locating a Tach source for your installation. When following the steps, the unit will begin to flash the parking lights if you have the Red/White wire connected to a tach source. If lights do not flash, then try anot...

Page 14 - TACH PROGRAMMING & TACH SIGNALS; INTRODUCTION; These Tach Signal locations mentioned are provided

TACH PROGRAMMING & TACH SIGNALS INTRODUCTION Tach signals will vary in levels and frequencies depending on many factors including the type of vehicle and the source of the signal. The signals from a vehicle’s injector wire and coil pac wire can vary greatly even on the same engine. The tach sign...

Page 15 - TIMED CRANK MODE; HOW TO USE THIS FEATURE:; attempt and may require a 2

TIMED CRANK MODE This feature provides an easy method of starting the vehicle without locating an exact tach wire. The system uses a timed cranking output combined with the use of the Red/White tach wire as an engine ON/OFF monitor. The Red/White Tach wire must still be used in this mode of operatio...

Page 16 - DIESEL GLOW PLUG DELAY; OPTIONS PROGRAMMING; OPTION PROGRAMMING CHART BEGINS ON NEXT PAGE

DIESEL GLOW PLUG DELAY This feature provides a solution for diesel vehicles without having to connect to the Glow Plug-“Wait to Start Circuit”. This may be needed for various reasons. If your vehicle does not have a viable “Wait to Start Circuit”, or you cannot locate and identify the circuit, then ...

Page 17 - To Engage Option Programming:

OPTIONS PROGRAMMING To Engage Option Programming: 1. Open hood (If no hood pin switch is installed, then ground the Gray wire) 2. Turn Key to the ON position. (Do not start vehicle) 3. Press the program / valet button 5 times. After a few seconds the unit will flash the lights 5 times. 4. Push the v...

Page 19 - OPTION DESCRIPTIONS:

OPTIONS PROGRAMMING OPTION DESCRIPTIONS: 1. Engine Monitoring: This option sets how the unit monitors your engine. You can program either for Tach mode in which the unit uses a Tach signal (RPM) or for Tachless mode that monitors voltage level. See pages 11-15 for more information and additional ste...

Page 20 - Brown Output Wire Function: Trunk Pop or Dome Light Output

OPTIONS PROGRAMMING 7. Horn Chirps on Remote Start: This option allows the unit to provide 3 short chirps when for audible confirmation of a remote start. The horn output wire must be connected for this feature. 8. Lock During/After Remote Start: This option controls whether the unit will automatica...

Page 22 - 00 VII TRANSMITTER / 999TW1/TW2 TRANSCEIVER CODE LEARNING; buttons; code, 3 flashes for the 3

900 VII TRANSMITTER / 999TW1/TW2 TRANSCEIVER CODE LEARNING Transmitter/Transceiver Code Learning: (Excludes RS901 model without remotes) Notes: Remote Transmitters/Transceivers come pre-programmed from the Factory. When re-learning remotes or adding remotes, ALL your system’s remote codes must be le...

Page 23 - COOLSTART

2-VEHICLE OPERATION The RS-900VII system can be used for 2 vehicle operation. A single remote can control two independent vehicles with an identical systems installed. NOTE: The RS-900 and RS-999 systems ARE NOT interchangeable. An RS-900VII system remote CANNOT control an RS-999TW1/TW2 and vice ver...

Page 24 - TROUBLESHOOTING: “BEFORE YOU CALL” SECTION; UNIT WILL NOT ATTEMPT A START (KEYLESS ENTRY FUNCTIONS NORMALLY):

TROUBLESHOOTING: “BEFORE YOU CALL” SECTION UNIT WILL NOT ATTEMPT A START (KEYLESS ENTRY FUNCTIONS NORMALLY): The unit is in Valet mode. Turn IGN ON, press and hold valet/programming button for 5-6 seconds then turn key off. Unit is now out of valet mode and should remote start. If optional LED is in...

Page 25 - JUMPER PIN DIAGRAMS

JUMPER PIN DIAGRAMS Jumper pins are used to change/configure the operation of the on board multi-function output PINK/WHITE wire, the Parking Light WHITE wire and the PINK glow plug input wire. See the diagrams below for Jumper Pin configurations. JUMPER PLUG SIDE VIEW JUMPER PINS JP1 JUMPERS: IGN 2...

Page 26 - ANTENNA DIAGRAM; WINDSHIELD

ANTENNA DIAGRAM WINDSHIELD ANTENNA LOCATIONS Blue Plug Black Plug RS-900 VII RS-999TW1RS-999TW2 Color of plug andreceptacle must match!! 26

Page 27 - BATTERY; SERIES; VII; VEHICLE

TRANSMISSION PROGRAM PARKING LIGHTS SW ITCH ECU RS900/901 ANTENNA/RECEIVER PLUG LED (-) UNLOCK OUTPUT +12 V FOR RELAYS (-) LOCK OUTPUT ENGINE ECU GREEN BLUERED FUEL PUMP PINK RED BROWN GRAY RED W HITE +10A or -.5A OUTPUT IGN RED/W HITE TACH INPUT ORANGE/BLACK: (-)HOOD SW ITCH GRAY (+12V) BRAKE PEDAL...

Page 28 - ONLINE TECHNICAL SUPPORT