Crimestopper CS-870RKE - Manual
Crimestopper CS-870RKE – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – TABLE OF CONTENTS; Wiring Diagram.......................................................................................................................13; PRE-INSTALLATION CONSIDERATIONS; BEFORE BEGINNING; with brake, and gas pedals, steering
- Page 3 – YELLOW WIRE: IGNITION SWITCHED “ON” AND “START” +12 VOLTS
- Page 4 – DETERMINING DOOR LOCK TYPE:
- Page 5 – POWER DOOR LOCK WIRING; Many Imports Late model Ford & General Motors
- Page 6 – Lock Outputs; NEGATIVE TRIGGER DOOR LOCK WIRING; Ground
- Page 8 – cut
- Page 10 – -WIRE RESISTOR DOOR LOCKS; See chart below for installation
- Page 12 – Watt; Green
- Page 13 – SYSTEM WIRING DIAGRAM; Jumper for Door Locks
- Page 14 – TRANSMITTER PROGRAMMING; indicating the unit is waiting for a 2; code, then press button #1 of a second transmitter or transceiver,; code and 4 times. If all 3; IGN
- Page 15 – OPERATION
CS-870RKE
REMOTE KEYLESS ENTRY SYSTEM
INSTALLATION & OPERATING INSTRUCTIONS
INTRODUCTION:
CONGRATULATIONS
on your choice of a Remote Keyless Entry System by Crimestopper Security Products
Inc. This booklet contains the information necessary for installing, and operating your system. If any
questions arise, contact your installation dealer or Crimestopper Security Products Inc. at the Tech Support
number below.
*IMPORTANT INFORMATION: Primary and Optional Features
-PRIMARY FEATURES:
These are features that must be connected in order for the system to operate
properly i.e. Power & Ground, along with the Primary features of Power Locks & Flashing Lights.
-OPTIONAL FEATURES:
Optional features are connected only if desired or agreed upon by the installing
dealer i.e. Horn Chirp and Trunk Pop. These features may require additional parts and labor charges. Consult
with your installer and come to an agreement about your optional features
before
installation. NOTE: The LED
is required for programmable options.
TECH SUPPORT
Mon-Fri 8:00 AM-4:30 PM Pacific Time
(800) 998-6880
www.crimestopper.com
[email protected]
REV. 01.2009
This device complies with FCC Rules part 15. Operation is subject to the
following two conditions: 1) This device may not cause interference, and (2)
this device must accept any interference that may be received, including
interference that may cause undesired operation. The manufacturer is not
responsible for any radio or TV interference caused by unauthorized
modification to this equipment. Such modification could void the user's
authority to operate the equipment.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
2 TABLE OF CONTENTS Pre-Installation & Component Mounting……………………..…………………………………………………2-3 Wiring……..……………………………………………………………………………………………………..…….3-4 Power Door Lock Wiring……………………………………………………….………..……………….…...……4-5 Negative Trigger Door Locks………………………….……………………...…......………………………………6 Positive Trig...
3 COMPONENT MOUNTING CONTROL MODULE: Locate the module underdash as high as possible. Driver’s Side usually provides an easy location for the majority of the wiring connections. The antenna wire should be routed away from any metal if possible. DO NOT alter the length of the antenna wire, or ground ...
4 WIRING WHITE WIRE: +12Volt PARKING LIGHT (On-Board Relay 10A) A) For Domestic Cars Signal Circuit: Cut 2 Diodes from W hite wire. Connect fused W hite wire to switched +12V parking light wire at back of light switch. If this is not possible, connect directly to one of the parking lights at the fro...
