Crimestopper RS-1303DP - Manual

8 WIRING: 7-PIN HIGH-CURRENT CONNECTOR BROWN: +12V STARTER OUTPUT 30A: Connect to circuit in the vehicle that has power ONLY while the STARTER MOTOR is CRANKING. GRAY: +12V ACCESSORY OUTPUT 30A: Connect to circuit in the vehicle that provides Accessory Power for systems such as HEAT and A/C. Typical...

9 WIRING: 7-PIN HIGH-CURRENT CONNECTOR FUSE RED PINK/WHITE 30A FUSE RED 30A + - BROWN PINK FUEL ENGINE BATTERY PUMP ECU GRAY + STARTER - COIL IGN OR ACC H/V/AC Diagram not to scale, for illustration purposes only. Your vehicle may differ. IGN 2 ACC 2 TOP WHITE START 2 FUSE PARKING LIGHTS IF NECESSAR...

10 Crimestopper Door Lock Accessories: CS-6600DLM: Dual-relay plug-in module for Reverse Polarity, Positive, or Aftermarket Motors. CS-6500DLI: Plug-in pulse inverter that converts the Negative outputs of the system to Positive type for Positive Door Lock systems. CS-610S1: Aftermarket door lock act...

11 BASIC DOOR LOCK DIAGRAMS AFTERMARKET MOTOR/DOOR LOCK WIRING REVERSE POLARITY DOOR LOCK WIRING GREEN GREEN FUSED FUSED RED RED +12V +12V BLUE BLUE + + 86 85 86 85 86 85 86 85 87 87 87 87 30 87A 30 87A 30 87A 30 87A + L CUT UL CUT MASTER SWITCH NEGATIVE TRIGGER DOORLOCK WIRING POSITIVE TRIGGER DOOR...

12 “SMART TACHLESS” MODE Your CoolStart system includes a unique voltage monitor called “Smart Tachless” mode. This mode allows this unit to efficiently start an engine without the use of a tach signal wire. These modules actively monitor the voltage level of the vehicle to control the starter motor...

13 TACH FINDER & USEFUL TIPS TACH FINDER MODE: This Tach Finder mode can assist in locating a Tach source for your installation. W hen following the steps, the unit will begin to flash the parking lights if you have the Red/W hite wire connected to a tach source. If lights do not flash, then try...

14 TACH PROGRAMMING & TACH SIGNALS INTRODUCTION Tach signals will vary in levels and frequencies depending on many factors including the type of vehicle and the source of the signal. The signals from a vehicle’s injector wire and coil pack wire can vary greatly even on the same engine. The tach ...

15 TIMED CRANK MODE This feature provides an easy method of starting the vehicle without locating an exact tach wire. The system uses a timed cranking output combined with the use of the Red/W hite tach wire as an engine ON/OFF monitor. The Red/W hite Tach wire must still be used in this mode of ope...

16 DIESEL GLOW PLUG DELAY This feature provides a solution for diesel vehicles without having to connect to the Glow Plug-“W ait to Start Circuit”. This may be needed for various reasons. If your vehicle does not have a viable “W ait to Start Circuit”, or you cannot locate and identify the circuit, ...

17 OPTIONS PROGRAMMING To Engage Option Programming: 1. Open hood (If no hood pin switch is installed, then ground the Gray wire) 2. Turn Key to the ON position. (Do not start vehicle) Pink wire must be connected! 3. Press the program / valet button 5 times. W ait for the unit to flash the lights an...

19 OPTIONS PROGRAMMING OPTION DESCRIPTIONS: 1. Engine Monitoring: This option sets how the unit monitors your engine. You can program either for Tach mode in which the unit uses a Tach signal (RPM) or for Tachless mode that monitors voltage level. See pages 11-15 for more information and additional ...

20 OPTIONS PROGRAMMING 7. Horn Chirps on Remote Start: This option allows the unit to provide 3 short chirps for audible confirmation of a remote start. The horn output wire must be connected for this feature. 8. Lock During/After Remote Start: This option controls whether the unit will automaticall...

22 TRANSMITTER PROGRAMMING Transmitter Programming: (Excludes RS-1300DP model without remotes) Notes: Remote Transmitters/Transceivers come pre-programmed from the Factory. When re-learning remotes or adding remotes, ALL your system’s remote codes must be learned at time of programming!! These syste...

23 2-VEHICLE OPERATION The RS-1300DP series can be used for 2 vehicle operation. A single remote can control two independent vehicles with identical systems installed. NOTE: The RS-1304/3/1DP and RS-1604TW1/1704TW2/1804FM systems ARE NOT interchangeable. An RS-1604TW1 system remote CANNOT control an...

24 TROUBLESHOOTING: “BEFORE YOU CALL” SECTION UNIT WILL NOT ATTEMPT TO START (KEYLESS ENTRY FUNCTIONS NORMALLY): The unit is in Valet mode. Turn IGN ON, press and hold valet/programming button for 5-6 seconds then turn key off. Unit is now out of valet mode and should remote start. If optional LED i...

25 JUMPER PIN DIAGRAMS Jumper pins are used to change/configure the operation of the on board multi-function output PINK/W HITE wire and the Parking Light W HITE wire. See the diagrams below for Jumper Pin configurations. JUMPER PLUG SIDE VIEW JUMPER PINS JP1 JUMPERS: IGN 2 (DEFAULT) ACC 2 (-) NEGAT...

26 ANTENNA DIAGRAM WINDSHIELD ANTENNA LOCATIONS Blue Plug Black Plug RS-1301/3/4DP RS-1804FM Color of plug andreceptacle must match!! RS-1604TW1RS-1704TW2 Black Plug W hite Plug Transceiver Box & Antenna Data port Data port Data port

27 TRANSMISSION PROGRAM PARKING LIGHTS SWITCH ECU RS-1300DP series ANTENNA/RECEIVER PLUG LED (-) UNLOCK OUTPUT +12 V FOR RELAYS (-) LOCK OUTPUT ENGINE ECU GREEN BLUE RED FUEL PUMP PINK RED BROWN GRAY RED W HITE +10A or -.5A OUTPUT IGN RED/W HITE TACH INPUT ORANGE/BLACK: (-)HOOD SW ITCH GRAY (+12V) B...

DATA PORT DIAGRAM This unit includes DP Technology it will allow you to plug our bypass modules model OFA-10/20/30 directly into the unit by via Data Port. The OFA module cable plugs directly to the Data port on the side of the unit . Please refer to OFA module manual for detail instructions. Vehicl...