Crimestopper CS-2205 - Manuals

Crimestopper CS-2205 – Manual in PDF format online.

Manuals:

Manual

Manual Crimestopper CS-2205

Summary

Page 2 - TABLE OF CONTENTS; Main System Wiring Diagram.......................................................................................................................19; INSTALLATION CAUTIONS & WARNINGS; BEFORE BEGINNING

2 TABLE OF CONTENTS Installation Cautions & Warnings…….……………………………………………………………...………………………………..2 Suggested Component Mounting………….…………………………………………………………….……………………….…...3 Wiring (Connectors H1-H8)…………………………………………………………………………………………………………3-12 . Power Door Lock Wiring...………………………………………………………………..………...

Page 3 - CONTROL MODULE/COMPONENT MOUNTING; For

3 CONTROL MODULE/COMPONENT MOUNTING CONTROL MODULE: The alarm control module should be mounted in a concealed location. DO NOT mount the control unit in the engine compartment. Fasten the module to a bracket or wire harness using the cable ties provided. ANTENNA MODULE: For optimum range and perform...

Page 4 - RED/WHITE WIRE: INPUT SOURCE FOR FLASHING PARKING LIGHT; Normally Closed

4 RED/WHITE WIRE: INPUT SOURCE FOR FLASHING PARKING LIGHT Connect to a +12 Volt source or Chassis Ground depending on the vehicle Parking light circuit. WHITE WIRE: +12V FLASHING PARKING LIGHT OUTPUT (optional) Connect to switched parking light wire at back of light switch or connect directly to one...

Page 5 - DETERMINING DOOR LOCK TYPE:

5 (H 4) POWER DOOR LOCK WIRING DETERMINING DOOR LOCK TYPE: We recommend determining the type of locking system the vehicle has before connecting any wires. Incorrect connection may result in damage to the alarm and/or vehicle locking system. This door lock information is provided as a guide. Your ve...

Page 9 - WIRING 16-PIN CONNECTOR; Negative Dome Light System:

9 WIRING 16-PIN CONNECTOR BLACK/WHITE WIRE: DOME LIGHT Illumination Output (Optional, Requires relay) Negative Dome Light System: Connects to terminal 85 of a relay. Connect terminal 86 + 12V Constant. Connect terminal 87 to Chassis Ground and Connect Terminal 30 to the Negative dome light activatio...

Page 11 - STARTER DISABLE DIAGRAM; NORMALLY CLOSED STARTER DISABLE; STARTER; NORMALLY OPEN STARTER

11 STARTER DISABLE DIAGRAM CUT START WIRE STARTER IGN SWITCH ORANGE N/C = NORMALLY CLOSED NORMALLY CLOSED STARTER DISABLE 87A 86 85 30 87 IGNITION WIRE (From the Alarm) RED WHITE Yellow ORANGE (ignition) CUT START WIRE STARTER IGN SWITCH ORANGE N/O = NORMALLY OPEN NORMALLY OPEN STARTER 87A 86 85 30 ...

Page 13 - WINDSHIELD

13 WINDSHIELD ANTENNA LOCATIONS CS-2205ADVTW1 RECOMMENDED CS-2205ADVTW1 Antenna System Window Mount Antenna Antenna Wire

Page 14 - PROGRAMMABLE OPTIONS; To Engage Option Programming:; interval between 1 second and 2 minutes); Latched output; pressed and will continue until the button is pressed again.; Latched output / reset with ignition; output but will reset or stop when the ignition is turned on.

14 PROGRAMMABLE OPTIONS You can program multiple options in one session if you start with the lowest option and continue on to higher options [if needed] without repeating steps #1-3 below. For example, you can follow the programming steps to change Option #2 to “OFF” by pressing the lock button on ...

Page 15 - PROGRAMMABLE OPTION TABLE; Function

15 PROGRAMMABLE OPTION TABLE Option # CS-2205 Alarm Function TX Button #1 (*DEFAULT) TX Button #2 TX Button #3 TX Button #4 1 Horn Pulse Door & Hood Trigger Only *All Functions No Warn-A-Way No Arm/Disarm Pulse 2 Auto lock with Ignition OFF *ON = Lock/Unlock Lock Only Unlock Only 3 Passive/Activ...

Page 16 - AUTOLOCK WITH IGNITION

16 PROGRAMMABLE OPTION RESET This system provides a reset method to restore all options to FACTORY DEFAULT VALUES as listed in the “Button #2” column of the programmable option chart on pages 18-19. This can be helpful if you have lost track of the option settings on your system, or when you are mov...

Page 20 - TRANSCEIVER / REMOTE CONTROL PROGRAMMING; will flash 3 times indicating its waiting for the 3; code and lights will flash 4 times for 4

20 TRANSCEIVER / REMOTE CONTROL PROGRAMMING 1. Turn key to the ON position. 2. Press Programming button 4 times, then after a few seconds the unit will flash the parking lights 4 times. Press buttons #1 (Lock) & #2 (Unlock) together at the same time of each transceiver to be learned. You should ...

Page 21 - STANDARD REMOTE; or

21 FIXEDANTENNA TWO-WAY REMOTE #3 #1 #2 #4 LOCK TRUNK PANIC UNLOCK AUX. #1 AUX. #3 STANDARD REMOTE #5 2nd CAR OPERATION 4 5 6 4/5/6 Advantage M C TM II #3 TRUNK #1 ARM LOCK #2 DISARM UNLOCK #4 PANIC Transmitter Button System Function Remark LED Remote Remote Sound Lock Doors & Arm System LED tur...

Page 22 - PARKING LIGHT:; ARM

22 LED display: LED Function LED Function Off Disarmed Zone 1 / Warn-Away Trigger Slow Flash Armed 2 flashes... pause Zone 2 / Trigger on Trunk/Hood Fast Flash Passive Arming 3 flashes... pause Zone 3 / Trigger on Door Switch On (Solid) Valet Mode 4 flashes... pause Zone 4 / Trigger on Shock Sensor ...

Page 23 - Second Vehicle Security Operation:

23 2-VEHICLE OPERATION: (CS-2205ADVTW1) Second Vehicle Security Operation: Your remote transmitter can be utilized to control a second vehicle security system. To program the remote control transmitter to a second vehicle, follow the instructions for Transmitter programming. All programming paramete...

Page 24 - OPERATION; Press the transmitter

24 OPERATION ARMING To arm the alarm and lock the doors, press the #1 Button on any remote. You will hear a single siren chirp and the lights will flash once. The system will arm, the doors will lock (optional) and the starter (optional) will be disabled. The red in-dash LED in the vehicle will begi...

Page 25 - Door lock with Ignition; SHOCK SENSOR BY-PASS; Press the

25 particular zone will NOT be protected by the alarm. All remaining functioning zones will still be protected if the system remains armed. AUTOLOCK/UNLOCK Autolock / Unlock allow the alarm to control the door locks automatically with the vehicle’s Ignition. W hen the ignition is turned on, 3 second...

Page 26 - TAMPER DISARMING; button from 1-9 times, the horn and siren will chirp on each press.

26 TAMPER DISARMING If alarm triggered, upon disarm the system, siren chirp 4 times, parking light flash 3 times. TWO STEPS DOOR UNLOCK (OPTIONAL) This feature will independently unlock the driver’s door only when disarming the security system. Pushing the button a second time within 2 seconds will ...

Page 27 - EXAMPLE: To Override The System With The Password Code 83, you would; THE ACTION OF THE 2-WAY LED REMOTE CONTROL TRANSCEIVER

27 EXAMPLE: To Override The System With The Password Code 83, you would; 1. Enter the vehicle and turn the ignition switch to 'ON’ position. (Alarm will sound.) 2. Within 5 seconds, Press and Release the Program/Valet button 8 times 3. Within 15 seconds of the last digit code enter (the 1 st code), ...

Page 29 - Program Mode For LED REMOTE TRANSCEIVER

29 Program Mode For LED REMOTE TRANSCEIVER Transceiver Button System Function Remark Program Mode - ( ) Button Lock Press within 5 seconds Program Mode - ( ) Power Save Mode Press within 5 seconds Program Mode - Switching code for 2nd / 1st Car Operation Press within 5 seconds Program Mode - + Demo ...

Page 31 - BATTERY REPLACEMENT

31 BATTERY REPLACEMENT Regular Remote Transmitter: If the range of your transmitter deteriorate, it is possible that you need to replace the battery. 1. Remove upper transmitter case. 2. Remove old battery from transmitter. 3. Install a new battery CR2032 (3 volt) noting the (+) and (-) marks in the...

Page 32 - REMOTE TRANSCEIVER DIAGNOSTICS; REMOTE SOUND

32 REMOTE TRANSCEIVER DIAGNOSTICS You may refer to the following statement once the security system with no action while you press the 2-way LED remote control transceiver button, REMOTE SOUND from remote transceiver LED on the remote transceiver Condition One “bi” sound while pressing the button of...