Crimestopper CS-2004 WDC - Manuals

Page 2 - TABLE OF CONTENTS; Installation Cautions & Warnings.................................................................................................3

TABLE OF CONTENTS Installation Cautions & Warnings…….………………………………………………………………………………3 Suggested Component Mounting………….…………………………………………………………….…………..3 Wiring……..……………………………………………………………………………………………………….…….4-5 Carjack Wiring………………..……………………………………………………………………………………..……5 Wiring-Mini Plugs………………………………...

Page 3 - INSTALLATION CAUTIONS & WARNINGS; BEFORE BEGINNING; remove vehicle dome light fuse while working on the vehicle.; DO NOT ROUTE ANY WIRING THAT MAY BECOME ENTANGLED; column, or any other moving parts in the vehicle.; CONTROL MODULE / COMPONENT MOUNTING; Mount the red; LED; in a visible location on the dashboard or console.

INSTALLATION CAUTIONS & WARNINGS BEFORE BEGINNING , check all vehicle manufacturer cautions and warnings regarding electrical service (AIR BAGS, ABS BRAKES, AND BATTERY). TO PREVENT A POSSIBLE DEAD BATTERY remove vehicle dome light fuse while working on the vehicle. MAKE CERTAIN TO REINSTALL FUS...

Page 4 - WIRING; BLACK WIRE: CHASSIS GROUND

WIRING RED WIRE: +12V POWER INPUT (15 Amp Fuse) Connect to a +12 Volt source with the supplied fuse and fuse-holder. We recommend the connection to be at the Vehicle’s Battery Positive Terminal. BLACK WIRE: CHASSIS GROUND THIS WIRE MUST BE CONNECTED TO THE CHASSIS METAL OF THE VEHICLE. Scrape away a...

Page 5 - OPTIONAL CAR JACK WIRING: SWITCH; HIDDEN BUTTON or; PINK; OPTIONAL CAR JACK WIRING:

WIRING WHITE/RED WIRE: (-) REMOTE OUTPUT 2 (Optional, Requires Relay) Connects the same way as Remote Output 1 above to activate or control a second AUX device or function. This output will provide a momentary negative signal when AUX 2 is activated. PINK WIRE: (+) CARJACK ENABLE Connect to push but...

Page 6 - DETERMINING DOOR LOCK TYPE:

WIRING – MINI PLUGS 2-PIN PLUG (SMALL): LED INDICATOR (RED FLASHING LIGHT) 2-PIN PLUG (MEDIUM): PROGRAM/OVERRIDE PUSH BUTTON 4-PIN SENSOR PLUG: RED WIRE SENSOR +12V POWER BLACK WIRE SENSOR GROUND * The Sensor supplied with the system does not require BLUE WIRE: NEG. WARN AWAY any additional wiring, ...

Page 7 - POWER DOOR LOCK DIAGRAMS

POWER DOOR LOCK DIAGRAMS UL REVERSE POLARITY DOOR LOCK WIRING + L NEGATIVE TRIGGER DOORLOCK WIRING UL L NOT USED UNLOCK WIRE CUT LOCK WIRE CUT FACTORY LOCKING RELAYS UL L + AFTERMARKET MOTOR DOOR LOCK WIRING UL L POSITIVE TRIGGER DOORLOCK WIRING FUSED +12V + UNLOCK WIRE LOCK WIRE FACTORY LOCKING REL...

Page 8 - STARTER DISABLE WIRING; Normally Closed Starter disable

STARTER DISABLE WIRING STARTER DISABLE PLUG: 3 ORANGE 14 GA. WIRES: (Normally Closed or Normally Open Configuration with ON-Board Relay) Note: read the following configuration options before connecting starter disable! Normally Closed Starter disable is the standard type used with most alarm systems...

Page 9 - JUMPER PLUG PROGRAMMING; SIDE VIEW; TOP OF MODULE; OPEN

JUMPER PLUG PROGRAMMING The jumper plugs are located on the topside of the control module behind a small access door. To change the programmable options on this system, jumper pins must be removed or shorted. See the diagram and chart for alarm configuration options. JUMPER PLUG SIDE VIEW JUMPER PIN...

Page 10 - JUMPER P1: PASSIVE ARMING

JUMPER PLUG PROGRAMMING JUMPER P1: PASSIVE ARMING This option controls the Passive (Automatic) Arming feature. If ON, arming will occur 30 Seconds after the ignition is turned off and the last door has been closed. The LED will begin flashing rapidly and the siren will chirp as a warning that the sy...

Page 11 - This jumper is not used for any alarm options.; JUMPER P9: REMOTE CARJACK FEATURE; TRANSMITTER PROGRAMMING; the parking lights come on solid.; transmitter code flashes 2X and third code

JUMPER PLUG PROGRAMMING JUMPER P8: NOT USED This jumper is not used for any alarm options. JUMPER P9: REMOTE CARJACK FEATURE This jumper controls whether the anti-Carjack functions of the unit can be activated through the remote control’s Button #2 (Unlock). Carjack protection will activate via the ...

Page 12 - ARM; BUTTON 2; OPERATION; BUTTON REMOTE TRANSMITTER: SECURWATCH® TRANSMITTER:; ACTIVE ARMING

#3 #1 #2 #4 SLNT LOCK/ SILENT/ AUX. 2 UNLOCK/ C RIM E S TOPPER AUX ARM DISARM AUX. 1 BUTTON 2 BUTTON 1 BUTTON 1 + 2 = BUTTON 4 (NO BUTTON 3 WITH WATCH) OPERATION 4 BUTTON REMOTE TRANSMITTER: SECURWATCH® TRANSMITTER: ACTIVE ARMING To arm the alarm and lock the doors, press the #1 Button on either tra...

Page 14 - PASSIVE ARMING / PASSIVE LOCK MODES; Doorlock with

OPERATION SILENT ARM/DISARM Use Button #4 (SLNT) for silent arm and disarm (Chirp Defeat). Press and release Button #4 to arm/disarm without the siren chirp. The light flash will be your only confirmation on Arm/Disarm. (Buttons 1+2 w/Watch) PASSIVE ARMING / PASSIVE LOCK MODES If programmed, passive...

Page 15 - CARJACK PROTECTION; on and press and hold the override button for at least 5 seconds.

CARJACK PROTECTION REMOTE OPERATED CARJACK (JUMPER PIN P9) This feature provides Active Carjack protection through the remote control and must be enabled before use through Jumper Plug J9 programming. When the Ignition is on (vehicle is running), press and hold the #2 Button (UNLOCK) for more than 2...