WEN AT6535 - User Manual

1. TOOL PURPOSE. This sander is designed to sand wood or wood-like products only. Sanding or grinding other materials could result in fire, injury, or damage to the workpiece. Using the machine for any other pur-pose for which it is not designed may result in serious injuries, machine damage and voi...

SPECIFIC RULES FOR THE SPINDLE SANDER 11. FEEDING THE WORKPIECE.• Allow spindle to reach full speed before feeding the workpiece. Do not turn on the machine while the sand-ing sleeve is contacting the workpiece. • Be aware of the direction of the spindle’s rotation (counterclockwise). Only feed the ...

1. EXAMINE EXTENSION CORD BEFORE USE. Make sure your extension cord is properly wired and in good condition. Always replace a damaged extension cord or have it repaired by a qualified person before using it. 2. DO NOT ABUSE EXTENSION CORD. Do not pull on cord to disconnect from receptacle; always di...

KNOW YOUR SPINDLE SANDER Dust Port (backside) Table Bevel Knob Power Plug Accessory Storage (on 3 sides of the machine) Spindle Spindle Upper Washer Sanding Drum & Sleeve Throat Plate Motor Ventilation Slots ON/OFF Switchwith Safety Key Work Table Mouting Holes UNPACKING With the help of a frien...

ASSEMBLY & ADJUSTMENTS Before using the spindle sander, you must configure the machine by instaling the appropriate sanding drum, sanding sleeve, throat plate and spindle washer for your operation. Check your packing list against the dia-gram below. If any part is damaged or missing, please cont...

ASSEMBLY & ADJUSTMENTS INSTALLING THE SPINDLE 1. Insert the spindle shaft (Fig. 1 - 1) into the spindle hole through the table opening. Spindle thead is M10-1.5. 2. Using one spindle wrench to hold the spindle seat in place, thread the bottom of the spindle shaft onto the spindle seat clockwise ...

ASSEMBLY & ADJUSTMENTS ADJUSTING THE WORK TABLE BEVEL The work table has the capacity to tilt from 0 to 45 degrees for sanding bevels on your workpiece. For any bevel sand-ing operation, you must use throat plate with an oblong-shaped opening. To adjust the table bevel: 1. Disconnect the machine...

ASSEMBLY & ADJUSTMENTS SQUARING THE TABLE TO THE SPINDLE When sanding with the work table in the horizontal (0°) position, make sure that the table surface is square to the sanding spindle. With the sanding drum and sleeve installed, check the alignment using a machinist's or combination. The sq...

OPERATING THE SPINDLE SANDER 1. Make sure that the machine has been securely mounted, and all accessories have been properly in-stalled according to the instructions in the "ASSEM-BLY & ADJUSTMENTS" section. 2. Plug in and turn ON the sander. Let the spindle reach full speed. 3. Maintain...

MAINTENANCE ROUTINE INSPECTION Before each use, inspect the general condition of the tool. If any of these following conditions exist, do not use until parts are replaced or the sharpener is properly repaired. Check for: • Loose hardware or improper mounting,• Misalignment or binding of moving parts...

PROBLEM CAUSE SOLUTION Sander does not turn on 1. Power cord or extension cord dam-aged or not properly plugged in.2. Safety key is removed from power switch.3. Defective power switch, defective motor or wiring, short circuit or loose connections. 1. Check the power cord, extension cord, power plug ...

EXPLODED VIEW & PARTS LIST 59 65 64 5 1 2 3 4 7 89 10 11 12 13 14 15 16 17 18 11 19 20 21 22 23 24 22 25 26 27 14 15 20 21 22 28 23 22 24 2930 31 20 21 22 32 3334 35 38 39 40 41 42 33 43 44 45 46 36 37 47 48 49 50 43 44 51 52 48 47 53 36 37 54 54 55 35 34 47 56 57 58 60 61 62 63 66 67 68 70 71 3...

WEN Products is committed to building tools that are dependable for years. Our warranties are consistent with this commitment and our dedication to quality. LIMITED WARRANTY OF WEN CONSUMER POWER TOOLS PRODUCTS FOR HOME USE GREAT LAKES TECHNOLOGIES, LLC (“Seller”) warrants to the original purchaser ...