WEN AT6535 - Manuals

WEN AT6535 Grinding Machine – User Manual in PDF format online.

Manuals:

User Manual

User Manual WEN AT6535

Summary

Page 3 - INTRODUCTION; to maximize safety for both yourself and others.

INTRODUCTION Thanks for purchasing the WEN Spindle Sander. We know you are excited to put your tool to work, but first, please take a moment to read through the manual. Safe operation of this tool requires that you read and understand this operator’s manual and all the labels affixed to the tool. Th...

Page 4 - GENERAL SAFETY RULES; WORK AREA SAFETY

GENERAL SAFETY RULES Safety is a combination of common sense, staying alert and knowing how your item works. SAVE THESE SAFETY INSTRUCTIONS. WARNING: Read and understand all warnings, cautions and operating instructions before using this tool. Failure to follow all instructions listed below may resu...

Page 5 - POWER TOOL USE AND CARE

GENERAL SAFETY RULES 4. Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energizing power tools that have the switch on invites accid...

Page 6 - SPECIFIC RULES FOR THE SPINDLE SANDER

1. TOOL PURPOSE. This sander is designed to sand wood or wood-like products only. Sanding or grinding other materials could result in fire, injury, or damage to the workpiece. Using the machine for any other pur-pose for which it is not designed may result in serious injuries, machine damage and voi...

Page 7 - CALIFORNIA PROPOSITION 65 WARNING

SPECIFIC RULES FOR THE SPINDLE SANDER 11. FEEDING THE WORKPIECE.• Allow spindle to reach full speed before feeding the workpiece. Do not turn on the machine while the sand-ing sleeve is contacting the workpiece. • Be aware of the direction of the spindle’s rotation (counterclockwise). Only feed the ...

Page 8 - GUIDELINES AND RECOMMENDATIONS FOR EXTENSION CORDS; ELECTRICAL INFORMATION; DOUBLE-INSULATED TOOLS

1. EXAMINE EXTENSION CORD BEFORE USE. Make sure your extension cord is properly wired and in good condition. Always replace a damaged extension cord or have it repaired by a qualified person before using it. 2. DO NOT ABUSE EXTENSION CORD. Do not pull on cord to disconnect from receptacle; always di...

Page 9 - KNOW YOUR SPINDLE SANDER; UNPACKING

KNOW YOUR SPINDLE SANDER Dust Port (backside) Table Bevel Knob Power Plug Accessory Storage (on 3 sides of the machine) Spindle Spindle Upper Washer Sanding Drum & Sleeve Throat Plate Motor Ventilation Slots ON/OFF Switchwith Safety Key Work Table Mouting Holes UNPACKING With the help of a frien...

Page 10 - ASSEMBLY & ADJUSTMENTS; PACKING LIST

ASSEMBLY & ADJUSTMENTS Before using the spindle sander, you must configure the machine by instaling the appropriate sanding drum, sanding sleeve, throat plate and spindle washer for your operation. Check your packing list against the dia-gram below. If any part is damaged or missing, please cont...

Page 11 - INSTALLING THE SPINDLE

ASSEMBLY & ADJUSTMENTS INSTALLING THE SPINDLE 1. Insert the spindle shaft (Fig. 1 - 1) into the spindle hole through the table opening. Spindle thead is M10-1.5. 2. Using one spindle wrench to hold the spindle seat in place, thread the bottom of the spindle shaft onto the spindle seat clockwise ...

Page 12 - ADJUSTING THE WORK TABLE BEVEL; MACHINE MOUNTING

ASSEMBLY & ADJUSTMENTS ADJUSTING THE WORK TABLE BEVEL The work table has the capacity to tilt from 0 to 45 degrees for sanding bevels on your workpiece. For any bevel sand-ing operation, you must use throat plate with an oblong-shaped opening. To adjust the table bevel: 1. Disconnect the machine...

Page 13 - SQUARING THE TABLE TO THE SPINDLE

ASSEMBLY & ADJUSTMENTS SQUARING THE TABLE TO THE SPINDLE When sanding with the work table in the horizontal (0°) position, make sure that the table surface is square to the sanding spindle. With the sanding drum and sleeve installed, check the alignment using a machinist's or combination. The sq...

Page 14 - OPERATING THE SPINDLE SANDER; OPERATION; ON/OFF SWITCH WITH SAFETY KEY

OPERATING THE SPINDLE SANDER 1. Make sure that the machine has been securely mounted, and all accessories have been properly in-stalled according to the instructions in the "ASSEM-BLY & ADJUSTMENTS" section. 2. Plug in and turn ON the sander. Let the spindle reach full speed. 3. Maintain...

Page 15 - MAINTENANCE; ROUTINE INSPECTION; LUBRICATION

MAINTENANCE ROUTINE INSPECTION Before each use, inspect the general condition of the tool. If any of these following conditions exist, do not use until parts are replaced or the sharpener is properly repaired. Check for: • Loose hardware or improper mounting,• Misalignment or binding of moving parts...

Page 16 - TROUBLESHOOTING GUIDE

PROBLEM CAUSE SOLUTION Sander does not turn on 1. Power cord or extension cord dam-aged or not properly plugged in.2. Safety key is removed from power switch.3. Defective power switch, defective motor or wiring, short circuit or loose connections. 1. Check the power cord, extension cord, power plug ...

Page 17 - EXPLODED VIEW & PARTS LIST

EXPLODED VIEW & PARTS LIST 59 65 64 5 1 2 3 4 7 89 10 11 12 13 14 15 16 17 18 11 19 20 21 22 23 24 22 25 26 27 14 15 20 21 22 28 23 22 24 2930 31 20 21 22 32 3334 35 38 39 40 41 42 33 43 44 45 46 36 37 47 48 49 50 43 44 51 52 48 47 53 36 37 54 54 55 35 34 47 56 57 58 60 61 62 63 66 67 68 70 71 3...

Page 20 - WARRANTY STATEMENT; THANKS FOR REMEMBERING

WEN Products is committed to building tools that are dependable for years. Our warranties are consistent with this commitment and our dedication to quality. LIMITED WARRANTY OF WEN CONSUMER POWER TOOLS PRODUCTS FOR HOME USE GREAT LAKES TECHNOLOGIES, LLC (“Seller”) warrants to the original purchaser ...