WEN 6321 - Manuals - manualsarea.com

Page 2 - TABLE OF CONTENTS; Technical Data; TECHNICAL DATA; Maintenance

TABLE OF CONTENTS Technical Data 234577891012 General Safety RulesSpecific Safety Rules For SanderElectrical InformationKnow Your SanderAssembly and Adjustments Operation Exploded View and Parts ListWarranty TECHNICAL DATA Model Number:Motor:Speed:Belt Size:Weight: 6321 120 V, 60 Hz, 7A 820 feet per...

Page 3 - GENERAL SAFETY RULES; DO NOT FORCE THE TOOL to do a job for which it was not designed.

3 GENERAL SAFETY RULES Safety is a combination of common sense, staying alert and knowing how your item works. SAVE THESE SAFE- TY INSTRUCTIONS. WARNING: To avoid mistakes and serious injury, do not plug in your tool until the following steps have been read and understood. 1. READ and become familia...

Page 5 - SPECIFIC RULES FOR THE SANDER; Always hold the tool firmly with both hands for maximum control.; ELECTRICAL INFORMATION; GROUNDING INSTRUCTIONS

5 SPECIFIC RULES FOR THE SANDER 7. Unplug the tool before changing accessories. Accidental start-ups may occur if the tool is plugged in during an accessory change. Before plugging the tool back in, check that the trigger is OFF. 8. After changing sanderpaper, rotate the sanderpaper to make sure the...

Page 6 - GUIDELINES FOR USING EXTENSION CORDS

6 AMPERAGE REQUIRED GAUGE FOR EXTENSION CORDS 25 ft. 50 ft. 100 ft. 150 ft. 7 A 18 gauge 16 gauge 14 gauge 12 gauge GUIDELINES FOR USING EXTENSION CORDS Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product...

Page 7 - REMOVING OR INSTALLING ABRASIVE BELT

7 AMPERAGE REQUIRED GAUGE FOR EXTENSION CORDS 25 ft. 50 ft. 100 ft. 150 ft. 7 A 18 gauge 16 gauge 14 gauge 12 gauge KNOW YOUR SANDER ASSEMBLY AND ADJUSTMENTS REMOVING OR INSTALLING ABRASIVE BELT WARNING: To avoid injury from accidental startups, turn switch OFF and remove the plug from the power sou...

Page 8 - ASSEMBLY AND ADJUSTMENTS; ADJUSTING BELT TRACKING; The belt life will be increased by using the tracking adjustment.; OPERATION; SWITCH; cause of the risk of fire from flying sparks.

88 ASSEMBLY AND ADJUSTMENTS ADJUSTING BELT TRACKING The belt life will be increased by using the tracking adjustment. 1. Turn the tool upside down and hold it firmly with one hand. Then start the tool and observe the tracking of the sanding belt. 2. Stop the tool and adjust the tracking of the belt ...

Page 9 - TOOL LUBRICATION

9 OPERATION Hold the tool firmly with both hands. Turn the switch on and permit the rotation of the abrasive belt to reach full speed. Then gently place the tool on the work piece surface. Move the tool back and forth. Never exert excessive pressure on the tool. The weight of the tool applies adequa...

Page 10 - EXPLODED VIEW AND PARTS LIST

Page 11 - Description

11 EXPLODED VIEW AND PARTS LIST Item Stock # Description 1 6321-001 Power Cord 2 6321-002 Cord Protector 3 6321-003 Cord Clamp 4 6321-004 Screw 5 6321-005 Switch 6 6321-006 Label 7 6321-007 Screw 9 6321-009 Right Housing 10 6321-010 Centra Housing 11 6321-011 Ceramic Plate 12 6321-012 Support Block ...

Page 12 - LIMITED TWO YEAR WARRANTY

12 WEN Products is committed to building tools that are dependable for years. Our warranties are consistent with this commitment and our dedication to quality. LIMITED WARRANTY OF WEN CONSUMER POWER TOOLS PRODUCTS FOR HOME USE GREAT LAKES TECHNOLOGIES, LLC (“Seller”) warrants to the original purchas...