Page 2 - Table of Contents; Information
Table of Contents Model Name Descriptions 3 Model Specifications 4 Important Safety Information 5 Before You Start 6 Warm Up Exercises 7 Assembly Instructions 8 Power Requirements 9 Console Functions and General Descriptions 10 Console Layout 11 Program Operating Instructions—Quick Start Manual Mode...
Page 3 - MODEL NAME DESCRIPTIONS
Product Name Definitions Each Smooth treadmill has a model name and unique serial number. The serial number label islocated on the back of the console upright. Model name sample: SMT9.2AB This model name is a Smooth 9.2 treadmill with programming andan AeroBelt. SMT —Smooth Treadmill 9.2 —Series num...
Page 4 - Model Specification Sheet
Model Specification Sheet MODEL SMT9.2P SMT9.2AB Horsepower Continuous 3.0HP 3.0HP Console Display Four Multi-function LED Four Multi Function LED Windows, One Multi- Windows, One Multi- function Dot Matrix function Dot Matrix Pre-set Programs 4 4 Custom Programs 8 8 User Defined Programs 2 2 Heart ...
Page 5 - Important Safety Information
Important Safety Information WARNING! Before using this treadmill or starting any exercise program, consult your physi- cian. This is especially important for persons over the age of 35 and/or persons with pre-existing health problems. The manufacturer or distributor assumes no responsibility forper...
Page 6 - Before You Start
Thank you for purchasing the SMOOTH treadmill! This quality product you have chosen was designed to meet your needs for cardiovascular exercise. z Before you start, please read the Owner's Manual and become familiar with the oper- ation of your new treadmill. z Remember to take the time to perform t...
Page 7 - Warm Up Exercises
TOE TOUCH STRETCH Stand bending your knees slightly and slowly bend forward from your hips.Allow your back and shoulders to relax as you reach down toward yourtoes as far as possible. Hold for 15 counts, then relax. This will stretch yourhamstrings, back of knees, and back. HAMSTRING STRETCH Sit wit...
Page 8 - Assembly Instructions
Minor Assembly Required!The Smooth 9.2P and AB treadmill is shipped in two pieces: the console upright assembly, and the base assembly. After opening the box, remove any packing materials from the treadmill. Do notthrow away any packing materials until the unit is working properly. The treadmill box...
Page 9 - Power Requirements
I M P R O P E R C O N N E C T I O N O F T H E E Q U I P M E N T G R O U N D I N G C O N N E C TO R C A N R E S U LT I N A R I S K O F A N E L E C T R I C S H O C K . C H E C K W I T H A Q U A L I F I E D E L E C -T R I C I A N O R S E RV I C E M A N I F Y O U A R E I N D O U B T A S TO W H E T H E R...
Page 10 - Console Functions and Descriptions
There are five LED display windows on the control panel to provide you with vital feedback information. TIME WINDOW z TIME: Indicates elapsed time after pressing start in minutes and seconds (0-99 minutes, 0-59 seconds) z PACE: Indicates number of minutes to complete 1 mile at current speed. SPEED W...
Page 11 - Console Layout
11 Console Layout, SMT9.2P and SMT9.2AB TIME WINDOW SPEED WINDOW DISTANCE WINDOW INCLINE WINDOW SPEED BAR INCLINE BAR CENTER BRICKYARD EMERGENCY RED SAFETY KEY (Place Here) Program Buttons (5) Power Stop / Start Pause Enter Program IMPORTANT! Please note that the Console Overlay used on the SMT9.2AB...
Page 12 - QUICK START / MANUAL MODE; Program and Operating Instructions; PROGRAM MODE
QUICK START / MANUAL MODE z Plug into a standard wall outlet (110-Volt AC, 15-amp circuit). z Stand on the treadmill and straddle belt. z Press POWER button. There will be an eight (8) second delay after pressing the POWER buttonbefore data can be entered. The TIME window will flash. z Press START/S...
Page 13 - PROGRAM MODE continued
PROGRAM MODE continued Customizing Pre-Set Programs z Customizing programs in P1 and P2 Mode: Each pre-set program can be customized in the P1 or P2 mode. After making the program selection, the top right window (CALO- RIES / DISTANCE) will read “OP.” ”OP” refers to “original program” and is preset....
Page 14 - Program Profiles
14 12 11 10 9 8 7 6 5 4 3 2 1 1 2 3 4 5 6 7 8 9 1 0 SPEED INCLINE 12 11 10 9 8 7 6 5 4 3 2 1 1 2 3 4 5 6 7 8 9 1 0 SPEED INCLINE 12 11 10 9 8 7 6 5 4 3 2 1 1 2 3 4 5 6 7 8 9 1 0 SPEED INCLINE SPEED INCLINE 12 11 10 9 8 7 6 5 4 3 2 1 1 2 3 4 5 6 7 8 9 1 0 Program Profiles The Rolling Hills Program is...
Page 15 - Belt Adjustment and Tension
WARNING! Do not overtighten rollers! This will cause prema- ture roller bearing failure! Belt adjustment and tension performs two functions:adjustment for tension and centering. Your new treadmillcomes pre-adjusted from the factory for tension and cen-tering. Please follow the procedures below if th...
Page 16 - Maintenance Instructions
WARNING! Before performing any maintenance to your treadmill, always unplug the power cord from the surge protector.CLEANINGRoutine cleaning of your Smooth treadmill will extend the life of your treadmill. WARNING! To prevent electri-cal shock, be sure the power to the treadmill is OFF and the unit ...
Page 17 - Treadmill will not start; Treadmill loses power during use.; Treadmill walking belt slows during use; Troubleshooting Guide
Treadmill will not start . 1 Is the Safety Key inserted into the treadmill Console? 2 Make sure the power cord is plugged into a surge protector, the surge protector is plugged into a properly grounded outlet, and the surge protector is turned on. (Refer to“Power Requirements” on page 8) 3 Check the...
Page 18 - Parts & Exploded View
18 Part # Part # 1 Left Side Extrusion Rail 05-0028 12 Front W heel (2) 06-0039 2 Right Side Extrusion Rail 05-0028 13 Uprights for Console (2) various 3 Treadmi ll Belt AeroBelt 04-0010 04-0014 14 Motor Hood Cover Top 06-0040 4 Front Roller Assembly 24-0106 15 Motor Drive Belt 04-0023 5 Rear Roller...
